BTF-LIGHTING5 Pin 32.8ft/10m 18AWG RGBW Electrical Extension Cable LED Strip Light Ribbon Wire Connection 5 Core Cord Line for 5050 Color Changing Flexible LED Tape Rope

I recently wrapped up a project that involved setting up outdoor RGB LED light strips. Going against the usual advice from manufacturers not to cut the strip, I found myself with no other choice for my specific setup. The real trick was to install the wires discreetly while keeping the lights working perfectly. After trying out a few different options, I stumbled upon the BTF-Lighting 32.8ft/10m 3 Pin 18AWG Extension Cable, and honestly, it was a total game-changer for the project.This particular extension cable is tailor-made for WS2812B, WS2811, WS2814, SK6812, and other similar RGB LED strip lights. Its versatility makes it a great fit for various LED projects. What really impressed me about this cable was its dependability and how user-friendly it was. I was initially pretty hesitant about splitting my LED strips, but this extension cable made the whole process seamless and stress-free.I was genuinely impressed with the wire quality. It’s 18AWG, which is sturdy enough to handle the power needs without causing any voltage drop-off. This means the LED lights work just as they should. The length of the cable, at 32.8 feet, gives plenty of room to work with, allowing me to route the cables just where I needed them, no compromises.If you’re in the market to extend your RGB LED light strips, this is the only product I’d feel confident recommending.

As described, strong wire when needed to pull on it a bit.

Very good quality. Used to build a LED strip light parallel circuit.

a advertised

Pictures hopefully help. Overall happy with how it all went together. Note that this wire did not fit with the 5-pin connector. The wire with the LED strip and connector kit has a thinner insulation then this wire. I ended up soldering the wires together and using some heat shrink tubing to protect the connection. Connection to the controller was really easy as was a small hole in the bottom of the kitchen cabinet to rout the wire trough. Here are all my details as reference.WOW, what can I say - an application and product that work together and was very easy to install. That does not happen all the time. I decided on BTF-Lighting for everything to keep it simple. Reaching out to their customer support was promptly replied to with a design to fit what I wanted. Opted for the brighter strip as this is task lighting under the cabinets in both the kitchen and laundry area. Only snag I had was the wire did not fit into the connectors, just some quick solder and heat shrink tubing did the trick. Installed the controller inside the bottom of the cabinet, power supply on the top shelf of the cabinet to prevent little hands from reaching it. Attaching the controller to the app could not be easier as was the attachment to the remote.Controller, WB5 - attached to IOSPower Supply, BTF-LIGHTING AC100-240V to DC12V16.5A Max198Wremote, BTF-LIGHTING LM096 RGB RGBW 4 Zone Touch RF RemoteLED strip, BTF-LIGHTING 5050 RGBW RGB+Cool White(6000K-7000K) 4 Colors in 1 LED 5mChannel, Muzata 5Pack 3.3FT/1M Sliver LED Channel System with Milky White Anti-UV Sun Protection CoverOverall very happy with how all worked together for a rather easy physical install and a super easy software install and connection in IOS, I would for sure do this again in the next house.

I used this to to connect several 5-conductor 10-amp 13-foot RBGW+ COB LED strip lights to each other and to a 40-amp 24-volt power supply. Soft vinyl insulation bends and strips easily, very fine stranded CCA copper coated aluminum wire, wire gauge seems accurate. No complaints.

The quality is very poor, and it’s not made of copper wire.

I used this for custom headlights. I was running hundreds of LEDs per headlights. Now anything over 18ga can be tricky to solder to the pads of the LEDs so I did double runs of power, single run for data, and double runs for ground. Transfers plenty of power, runs data perfectly (blueghozt module) and it's not too difficult to solder down.