VVIVID Epoxy High Gloss Black Carbon Vinyl Automotive Wrap Film DIY Easy to Install No Mess (1.5ft x 5ft)

I bought this black carbon fiber wrap and really like it. It’s easy to install, and the glossy black carbon fiber finish looks very elegant. It’s flexible, applies well to different surfaces, and gives a professional-looking result. Great for DIY projects and for adding a stylish touch to your vehicle or other items.

Good stuff, easy to work with.

Product is very nice, I was happy with the appearance, unfortunately I found it much harder than it looked to apply. I tried my best to use it on a door panel, but could not get it to stick in one of the corners. But the worse was that small specs of material will leave a tiny bump visible on the outside. Obviously you need the layer perfectly clean. In my case it was very difficult to have a perfect application layer because of a thin layer of some substance that I just could not sand off fully. I will try again later on other surfaces and parts that are more suitable and easier to learn on.

First off got to say I got this specifically because carbon fiber parts for my car are hard to come by and Incredibly expensive so when I saw this stuff with the high gloss I pulled the trigger on it and got a few rolls and I'm very pleased with the results. I did my shifter console plate and my t-tops on my 86 Trans Am and the stuff at first was a little Troublesome to work with but once you get the hang of it and figure out where to start and where to work to it goes fairly easily especially since it's not like window tint where once it's stuck at you're done you can actually pull it up and retry and refitted a few times and applying heat to it helps Flex it around Troublesome curves you just have to know what spots to hit the heat with and what spots not to otherwise it will contract and expand in the wrong places and then you'll end up getting a crease and it will stick to itself. And then with the larger role that I had that was five foot by 6 foot I took on wrapping a fiberglass hatch and came out looking like it was bought as a molded carbon fiber hatch , took about 3 hours but if you're patient there is literally no limit to what you can do with this stuff . Make sure you got a good quality heat gun don't use it too much in one spot and have a really really sharp razor blade

Can't go wrong with this wrap, and especially considering the cost. Very satisfied

Product is no good the adhesive is terrible it’s peeling off after a day off installation. Im very disappointed because it looked so good after installing. Also it bubbled a lot after installing. The corners shrunk a little bit in the areas i stretched the material so in the pictures you will see it not covering the whole thing because of it.

So I have used many different carbon wraps over the years even way back when it was not a thing. I have to say They have come a long long way. This is definitely one I recommend to my clients as a great beginner’s project. I tell my clients to always leave a little extra then use the heat gun and smooth it out. It will shrink and it can stretch nicely. It is somewhat forgiving. It was extremely wrinkled right out of the box. Sadly that whole area was a waste even after using heat gun. For straight areas this works wonders and you will get a great finished piece. For arches dashes and around gauge clusters you need to leave a little extra so you won’t be left with short edges once it sets in. I found it easy to work with However the three stars was because of the lifting in some areas and excessive shrinking in rounded areas and because way too much of the product was creased and needed to thrown out. The epoxy black was my favorite, the matte grey was awful to work with and looked like a matte cheap sticker.

I've never liked vinyl carbon fiber, it always looks very fake and cheap. However, I really wanted some trim pieces in my car to be carbon fiber. I searched around and stumbled on this product. I decided to give it a go, along with 3 other brands and I would simply pick whichever I liked best. I had never heard of VVIVID before so I wasn't expecting too much. Holy cow was I wrong. As soon as I took all the vinyls out of the box, I immediately knew which one to use. This stuff looks great, it has depth and reflects light more like carbon. I was so impressed with the looks that I packed up all the rest and sent them back. I just spent the past few hours wrapping some trim pieces with it. It is quite a bit thicker than most other vinyls, so it will definitely take some heat to get it to do what you want. Some people say it doesn't stick, but they must not have watched the companies installation videos on how to activate the adhesives. It is designed not to be too sticky at first so you can reposition it easily, then you activate the adhesives with heat according to their instruction. I had no problem getting it to fit very complex curves and corners. It seems to stick very well. IMO, you need to get the "VVIVID Epoxy High Gloss Black Carbon fiber", their other carbons dont look as great as this does. All in all, I liked the end result so much that I logged onto Amazon at 1 am to write this review. :D

Looks good but needs heat to stick

Caché très bien fait une belle finition

No batallamos para forras los bo, súper recomendado 😍

Really happy with this carbon wrap. Used a heat gun to wrap carbon around door handle, easy to use and looks great!

Check out a few DIY guides on youtube before trying it out. It'll save you a lot of money.