TALON Grips Adhesive Gun Grip for Glock 19, 23, 25, 32, 38 (Gen 1/2/3) – Made in the USA

I bought these in 2015 for my gen 3 G19 edc and they are still holding on (after 9 years the edges are starting to lift). If you want a quality product, then you have found with Talon Grips. Easy installation, great fit, and just plain lasts. They add a great texture and improve the feel of the grip. I'll definitely be buying these again.

Having had some poor experiences with installing sticky products before, I was a bit hesitant to order this grip. However, it was surprisingly easy to attach to my G19. It was forgiving if I made an error in that it was not at all ruined if I needed to pull up an edge to try again. While it comes in one piece, there are slits in a few places to help it conform to the existing grooves on the stock grip. It aligns perfectly to avoid covering the rear of the magazine release and even the Glock logo on the left side side. Per the instructions, I used a heat gun on a low setting to finish molding the grip into place; it indicates a hair dryer would also work if you do not have a heat gun handy. It is not yet clear how well this grip will hold up over time, but the rubbery feel is a marked improvement over the standard Glock grip (which I had thought was fine for the last decade). Given the relatively low cost, I have gone ahead and ordered another one for a different Glock.

The description states in UPPER CASE that this grip is for pre Gen 4 Glocks only, shame on me for not reading the full description. It did sit in a wishlist for some time... meh. That being said it did fit my Gen 4 G23, with the medium backstrap, with a tiny bit of trimming. The grippy overlapped the magazine release by about 3 mm on the left side (w/ Md backstrap) however the right side cleared the release by more than 5 mm. Being a left handed shooter I have the release reversed so I was able to lay the grippy right over top and carefully cut a notch once everything was in place. I also trimmed 1-2 mm off the bottom wings of the grippy's back (once positioned and glued). I haven't gone back to check if TALON has a Gen 4 template but even if they don't I would not hesitate to buy this again for my Gen 4. This grippy improves and extends the original grip surface area in all the right places (read all of the places). The gun always felt good in my hand but now it feels gooder. The construction of this thing is spectacular. From the singe marks on the paper backing it looks to be laser-cut and the precision of the edges confirms that. The instructions were more than acceptable and they give you a neat sticker to stick on something.. probably not your gun. Edit: Duh of course they have a grip for the gen 4. I suppose I'll get the right grip if this one ever falls off but I'm in no hurry

Great grips. As a military veteran, these grips are rugged and comfortable. Highly recommend. Have had them for five years now and still going strong.

Ordered rubber for my gen3 and when the sandpaper version arrived I was upset, but turned out to be a happy accident. Instead of returning, I decided to give it a shot (while I waited on my second order - the rubber grip) and I cannot recommend it enough. Now I do not CC - I live in a remote place where being armed is a kind of requisite (bears, etc) so I cannot speak to how comfortable or not that might be if concealed. But in terms of gripping the gun - especially with dirty/wet/cold hands - it is a whole other thing. Honestly, I'd have said I had a solid grip on my Glock BEFORE applying this thing - but with the granulate wrap it is like perfection. Keeping the rubber one for a back-up, but if you want to make sure you have a tight handle on your weapon in very cold/wet weather then the granulate is the way to go. Tip: just my two cents, but I waited for a hot day and then walked around for a couple hours tightly gripping the weapon (after following the instructions w/ blow-dryer, etc) and it really did make a little difference when it had completely adhered to the grip - feels like it was made just for my hand

Good product, easy enough to put on the gun after watching a few youtube vids. Actually, I didn't think I needed this grip so much, my hands didn't slip much without these grips and my accuracy is pretty good. Still, Hickock45 seemed to like them and...well, it'd been a while since I bought a new gun-related item, so I thought I'd treat myself just after Xmas and try it out. I like it! There is a definite advantage and more positive feel I get with the grip on rather than without, the grip is not so thick that there's a real discernible "squish" to the feel. For reference, I probably had about 8,000 rounds on my Gen 3 Glock 19 without the grip and now have about 800-1000 rounds shot with the grips. While this product's not likely to fix anyone's problems with a poor or flimsy muscular grip (it's better to get some grip strengtheners for that and/or do a lot of pullups/deadlifts/farmer's walks for grip strength) it is nice to have a solid, positive feel on the gun. Only drawback I can think of is the price, $17 or so bucks for a thin piece of cut rubber (albeit very precisely cut rubber) seems a little much, but I do appreciate Talon's making a good, solid product.

Have these on 4 pistols. Love them. Transforms the fit and comfort. Durable as well. In and out of sleeves, holsters, Pelican cases, grip/adhesive still in place. Improved shooting control on some smaller pistols that are hard to hold.

I resisted buying these Talon grips for years because I just didn't think they were necessary. I shouldn't have. The feel of the grip in my hand is greatly improved, much more positive and secure. Packaging was excellent and instructions were clear and thorough. I carefully followed the installation instructions and now it looks like they were installed by Glock at the factory. The only negative (if you can call it that) is that the magazine is now kind of tight fitting. I suspect that this is a result of using a blow dryer on low heat to set the grips as recommended in the installation instructions. I expect that it will loosen up with use over time. While the Talon grips are a more expensive option than other products on the market I like the all one piece, precision fit I got from them.

Hab sie für meine Glock 19x 4,5mm gekauft. passen sehr gut.

Great feeling grip, not cheap at all. I just trimmed off the little tab that joins the sides for a cleaner look and it works awesome on my 19 Gen 4

nice!!

Added just the right amount of grip.