CloudValley Webcam Cover Slide, 0.023in Camera Cover for Laptops, MacBook Pro, MacBook Air, iMac, iPad, PC/Computer, Tablets, Ultra-Thin Web Blocker Protecting Your Privacy [4-Pack]

The adhesive is great. The whole thing is so thin I don't even notice it most of the time. Doesn't get hung up on pockets. Slider works flawlessly. 10/10 would recommend 👍 I'd but these again in a heartbeat.

Item as described. The price and shipping are great.

Like them to get privacy from the computer when not using the camera

Pros:- installs very fast and stays on well- manual camera blockage is the best way to know you aren’t showing your boss that it’s 2pm and you’re still in your PJs.Cons:- on my Surface Pro, the different sensors are very close to the camera, and even as small as these are, it was tough to put it on straight and ensure it wasn’t blocking anything.(Tip: I left the camera on while installing, and only peeled 1/2 of the backing away from the adhesion, until I had it placed where it wasn’t blocking).- it’s difficult to tell (because they are black, and so is the camera on my computers) whether the slider is blocking the camera or not at a glance. I fixed that with fine paint pens, coloring in the slider and the backing that shows when the camera is covered. So, when the camera is open, you only see the one dot. When it’s closed, you see the entire oval. You could just slide it to check, but these feel a little flimsy, and I didn’t want to mess with them that much.Overall, I’m happy with them. Cheap, easy, and they look nicer than my pink post it note covering them prior to these.

This is the third purchase of a webcam lens cover and it almost works perfectly. Is ultra thin and doesn’t seams to prevent the MacBook Air 2020 to close properly, but it does added a gap that worries me that could damage the screen since a gap indicates that pressure is concentrated in a spot. What makes it thicker seams to be the adhesion film as shown in the last picture. The sticking film added to the products makes it twice thicker.I also tried other magnetic version considering that should be thinner but the cover falls apart. So far seams to be a good product, made of metal. I wish it could be a little bigger to make it easier to slide, but not so big that it could interfere with the ambient light sensor usually at the right of the camera. It is a little bit hard to slide since is very small, but it might improve overtime while using. However is a good thing that it doesn’t slide on it’s own as reported by other versions of camera covers. If they can make the sticking part thinner the product will be perfect.

The camera cover is extremely thin with a low profile so it won't interfere with how your laptop closes. There will probably be no gap as this camera cover will seat beneath the small lip surrounding the inside of the laptop lid on most laptops. Easy to install. Just take time to see where the camera lens and microphone holes are located and how the cover should be located before you remove the paper on the adhesive. Press gently for a minute so that the adhesive can set on the surface around the camera lens.

I chose this cover because iPads were listed. It has a bigger opening now where the camera is located. ONLY reading the instructions included, did it state there was a problem with some iPads!! Mine is only two years old. It would be NICE if they mentioned this in the description. They Obviously KNOW there is a problem.The first instruction: "Clean the edges of the webcam cover!" :-) I wondered... how did it get dirty? It is packaged and sealed! I think it should have read... clean the glass on the webcam where you are going to attach it. They use this transparent tape to put on the front to line it up and press and hold for a few seconds. That is nice. They don't ever instruct you to Remove the Blue tape covering the Back of the Camcover so it will Stick when you press and hold it a few seconds! You see that if you watch the video. Some people I know do not understand things like that unless explained.For those you cannot read their TINY TINY print. You are suppose to leave it for 24 hours before it is Fully Adhered. Many glues like this take 24 hours to set. Great for an average phone and smaller, older iPads perhaps. I feel they should have added more Details in their Description, and not in the instructions! Because it was a Waste of Money "for me."

After years of using ugly, black electrician's tape to cover my laptop's camera, I am so happy to have found this ingenious little gadget. It's small, thin, and simple, which is exactly what I was looking for. It doesn't impede my laptop from closing at all. The black color of the webcam cover blends in with the black bezel around my laptop screen. I don't even notice the cover because it blends in so well. Because of its small size, it does require a steady hand and good lighting when applying. On my MacBook Pro 16", I tilted the screen so that I could see where the camera was, I lined it up and applied the cover. The webcam cover opens and closes smoothly. If applied correctly, when the cover is open it doesn't block the camera. When closed, it completely covers the camera, so that only black can be seen instead of an image. I'm going to order more for my family. Highly recommended! A+