iGreely 10 AWG SAE to 5/16" Ring Terminal Battery Cable, UL1015 Tinned Copper 2-Pin SAE Quick Disconnect Connector, Battery Lead for Motorcycle Automotive Car RV Marine Solar Panel 2FT

I bought them to use with my deep cycle batteries on my travel trailer tongue. I also have spare deep cycle batteries I carry in the back of the truck that I use with the trailer or take along when I go tent camping so that I can run some 12V items I take camping. I use the same type 2 pin connectors on those items that are on the fused harnesses. It makes it easy to plug and unplug the batteries without having to loosen the nuts on the battery terminals. I used similar trolling motor connectors but I had to add fuse holders and ring terminals to those. These harnesses are all in one.

This worked really great for my fuel tank set up. Installed easy and enhances the battery life on my fuel tank

I used this to have a way to easily connect my portable solar panel with integrated charge controller, to my RV coach batteries.The batteries are physically under the steps when you enter the RV, so the alligator clips won’t really fit, and there is high likelihood they would contact the underside of the metal step and cause a short across the battery.These allowed me to have something that both fits cleanly with minimal obstruction to other stuff, and route the wire just far enough i can safely plug in to the solar panel plug.FYI, if you are using this with a Zamp portable solar suitcase, they come with either alligator clips or an SAE plug that would plug into this. Since Zamp reverses the positive/ negative on the SAE connecter to their unit, (the female point is the positive side), i needed to get a polarity reverser fitting or else it would be connected backwards when you plug it in to this. The good thing is that this has a built in fuse with 3 sizes of fuse included that you can match up with the size of the solar charger. So you have some protection if you connected it backward. If you own a Zamp panel and wanted to be extra safe like i was, i connected up the alligator clips to the panel connection first so i could figure out using the colors of the alligator clips which side of the plug was positive and which was negative, then i put a mark on the plugs to record that. Then when i connected the little jumper that connected to their port and had a SAE fitting on the other end, i could see for sure which side was negative and which was positive. Thats how i knew i needed a polarity reverser to connect to this.Not that theres anything wrong with this item, as it is standard design to accommodate most things like battery tenders, etc. Zamp just has a different connection and as such i needed the little polarity reversers that are a couple dollars to use this item with their stuff.Can’t emphasize enough to not rely on the fuse to protect your equipment from damage and yourself from electric shock. Always be careful of what is touching what when near battery terminals and always be 100% sure you are connecting positive and negative leads correctly. I have damaged equipment in the past which is why i am extra paranoid now.

This was for my motorcycle. I love it except that I thought the fuse holder was larger than it probably needed to be. I managed but it was tough getting the fuse holder to fit into the limited space on the motorcycle.

The quality seems great, the fuse holders and wires are very large and solid, which is expected with 10awg.The only issue with it using it on a vehicle is the polarity is reversed, the male side on the SAE connector should be the ground side, that way if it comes disconnected the positive side is protected and won't short circuit to the frame on a vehicle. I assume the reason they did it this way is because if the SAE connector was connected to a solar panel then the wires would be correct to charge a battery off of it. I wrapped the wires completely in Tesa tape so that the colors are no longer visible, and marked the fuse holder and SAE connector with a paint marker and then connected the wires to the opposite battery terminals than what the colors would suggest. The only way that it was possible to swap the two wires was because both sides have the fuses.

Permanent connection with battery tenderworks perfect

Heavy duty, fabricated ends to easily connect to battery. Bought 12 or more before and learned to only get 12 or heavier gage, this is 10 gage and is the best by far.

Got here quick, easy to hook up, works like a champ

Very well made. Will be using to power a 12 volt water pump during fishing season :)

works ok now I got the plug around the right way

Good quality. Nice to find the thicker 10 gauge wire for SAE connectors. I leave this connected to the trailer battery and hanging just out of the lid for fast access.