iJDMTOY 3-Inch Projector Fog Light Kit w/ 40-SMD Amber Yellow LED Halo Ring Angle Rings, Universal Fit With Car SUV Truck ATV RV, etc

I make a lot of purchase on Amazon and this is one of my TOP Purchases!!! This one of the few designs with a chrome/stainless ring that I've had been searching for a while. Here are the dimensions as my install was on a flat surface.This look is Awesome as the ring is exactly 3" in diameter lip and the base tapers back. For the best fit, what ever it needs to be fit must insert into the lip well at least 2 7/8" inner. It's a GREAT High End Look. Two separate wiring for (+) and (-) for both the LED ring and Projector and attached to my toggle switch. I have the ring on for daylight or both, but the very brigh daylight (Not cool blue or warm light) LED ring really makes this a great purchase that's found in high end models.

small and very functional add to my old car!

Love how bright they are just the Halo part But then again not worth the money that I spent already went out.

These are pretty sturdy well built units. This is DIY so beware they will require retro fit. The brackets that come with them are pretty much useless and the included light was a waste. I changed out the light for an led upgrade and the results are great. The halo eyes are very bright and will make great daytime running lights.

They are very nice but do not fit my car as stated. I would have to do alternations to get them to fit.

I have 2014 Jeep Wrangler with smittybilt bumper which has a 3'' fog lights. I bought this because of the good reviews but unfortunatly it is very bad.Pros:1- The LED ring is nice and bright2- plenty of wires in lengthCons:1- The screw for negative wire that is also holding the bulb striped with no force applied = no was to connect negative wires2- the box came with only 2 screws and 4 holes for bracket3- it is very long that it may hit the tires in some cars4- the bulb doesn't have a rubber seal and is 100% NOT waterproof SERIOUSLYThe bottom line. If you want to install it you have to modify a lot to make it fit

It’s made with high-quality plastic and it is very well-made fit perfectly in my 2005 Nissan Altima SE

I have not installed the unit yet because I'm waiting for other parts so this review is purely on build quality and what you get. Because of it not being installed yet is the only reason it's not getting one star. First off, the reflective front housing for the halo lights is not metal, it's extremely cheap plastic and is easily broken if you tighten the screw or bracket around it. Second, if you end up using an aftermarket HID kit or LED kit, which is the biggest reason for getting these over other fog lights with prebuilt in lights that aren't very bright, it becomes not waterproof anymore due to the way the 9006 bulb screws onto the back. Because of this, I would recommend a high quality LED kit that is made to be waterproof because I'm not sure how long HIDs would last when splashed with water from the rear area. Third, the black paint coating on the metal housing is extremely easily damaged and will probably come already flaking off near where ever there is friction or two pieces meeting such as where the screws are located. Fourth, the equipment comes with two, count them, (2) sets of screws. If you look at the images, you can clearly see what the bracket looks like and I would expect to use at least two sets of screws for EACH light but nope, I was told by the seller that the screws are for the center hole only and I need to use the screws from my factory lights. Isn't the whole point of universal aftermarket fog lights is to put them on cars that didn't have factory ones installed? Or even in this case since it's "JDM", what about people who also have aftermarket bumpers that have no oem parts? Seriously? I wouldn't attach these to my car with a single screw in any case. There are no instructions at all showing you how to even attach the bracket onto the lights at all and there are no extra holes for screws. I ended up removing the screws from the sides near the cheap plastic clips holding on the front face and squeezing the bracket on over that and putting the screws back on over the bracket and plastic silver clips. Clips that have bent and creased because of the tension on the screw. Tension that is required if you don't want the light to swivel up and down randomly since a car is meant to move and encounter bumps. There are literally no other mounting locations on the housings themselves so I don't even know how to attach them using the "center" hole using a single screw. Even if I could, the other end of the bracket made of two prongs wouldn't attach anywhere on the car anyway. This is what I'd expect from a set of fog lights at less than half the price, and they're out there. I expected better quality than this from both the product and the seller for the amount paid. Less than $5 worth of metal and crappy everything else including an incomplete mounting system that was done on purpose doesn't justify the price.