Edge Supply Walnut 24 x 96-inch, 3M Peel and Stick Wood Veneer Sheet – Self-Adhesive Wood Veneer, A Grade, Smooth-Finished – Versatile for Furniture Restoration, Cabinetry & DIY Use

Pros- good wood quality. Prepped project substrate with three coats sanded polyurethane that provided smooth surface for excellent adhesion of 3M PSA. Veneer cut easily with box cutter/heavy scissors leaving very clean edge. Veneer flexed nicely in vacuum press to adhere to waterfall edge and curves. Cons- eighth of an inch gap between edge of veneer and adhesive in some spots. Probably would have been okay without, but added bead of glue anyhow. CAUTION- you basically get one shot at getting placement right once you remove the PSA backing. The PSA adheres instantly so ensure you’ve got your veneer cut and placement right BEFORE you peel. Excellent product that I’ve already purchased again for next restoration. It’s a little pricey, but I didn’t want to mess with glue required for less expensive non-PSA veneers- anything to reduce the number of variables for my first veneer project. Very pleased.

The item description is wrong, this is not peel-and-stick. It is PSA, pressure-sensitive adhesive. It is slightly tacky and easy to work with, then apply pressure to set the adhesive. So far, no failures. Vaneer grain quality was excellent and similar to the picture. Very pretty product and very easy to use. Shame about the poor item description.

This is such a great looking, beautiful veneer. Easy to use, I put it on a vintage speaker pair (AR4xz) and left the original vinyl covering on. The adhesion is superb and the look is fantastic. I used a clear acrylic to preserve the natural (light) color of the walnut rather than darken it with typical varnishes or other applications; the results are superb.

This stuff is great. Used it to renew the cabinetry in a campervan conversion. It's so thick that it hides any blemishes (like raised screwholes, etc.) in the surface it's adhered to. It took "dark walnut" colored Danish oil beautifully, and was finished with a coat of beeswax. I started with one roll and ended up ordering many more. My only grip is that the adhesive doesn't extend all the way down to the cut edge (which is exactly where it's needed the most). There is a centimeter or two strip along the edge without adhesive.

I’ve ordered this walnut edge banding twice and have been impressed with the quality. The grain pattern is consistent with natural variations, and the veneer is thick enough for minor sanding if needed. It’s easy to apply with a standard iron (cotton setting works well) and adheres strongly across surfaces like plywood and deglossed laminate. Just be careful not to overheat, as it can cause the adhesive to run slightly. Durability has been excellent with no peeling or lifting, even on multiple projects. For trimming, both manual edge trimmers and a router with a high-quality flush trim bit work smoothly. The product is versatile for furniture projects, and even beginner woodworkers will find it straightforward to use. My tip for best results: ensure the surface is well-prepped and dust-free to maximize hold.

Ruined a vintage china cabinet that I was restoring. I properly prepped and cleaned all surfaces and used a j roller to press the veneer on. I relaxed the veneer ahead of time and acclimated the furniture and veneer in the same space for 2 days before installation. I’m so mad about the time I’m going to have to spend to peel the veneer off and see if any of it is salvageable. I was in the fence about using adhesive backed and I should have gone with a separate glue down veneer. I’ve lost days worth of time due to this mistake of a purchase.

Easy to work with and packaged well, but the pressure marks ruined the finished look of my project. I’ve invested too much time and money into it at this point to start over. After sanding for days, carefully avoiding burn-through on the veneer, the wood looked significantly lighter—until I applied the finish, which made the defects “pop,” and not in a good way. My project is a very expensive antique, so I have no choice but to live with it, but I wanted to make others aware. Unfortunately, I only just found the other reviews from people experiencing the same issue.

The wood was beautiful and worked very well. The adhesion was good. (I first applied a finish to the raw plywood to ensure a smooth surface, as recommended.) It took stain well and the finish was a good match to the solid wood frame I used. One note - the first shipment I received had a machine mark - a scratch - that was all the way across one end of the veneer. Otherwise it was fine. I called Amazon and they immediately sent a replacement roll and issued a pickup for the roll with the scratch. Great job Amazon.