FEETECH 35KG Servo Motor 7.4V High Voltage Waterproof High Torque RC Servo Full Metal Gear Digital Servo, Aluminum Case, Control Angle 180° for 1/8 1/10 RC Cars, TRAXXS x4, Baja, RC4WD, GTR and More

TLDR; No regrets for less than $30 shipped Tough lil servo will probably last for ages on 6-7.4v. Just watch your mounting clearances & make sure the bottom section doesn't get crushed. Over-all mounted height was the same, but mounting tab height wasn't quite clear in the description. This one is about 5mm taller from the mounting tabs to the bottom. (ITEM DESCRIPTION HAS BEEN UPDATED 👍🏾) It's a little taller than my old servo, so small (metal) spacers are needed between the servo mount & chassis of the Arrma Typhon 6s that it was purchased it for. My old brass inserts were used inside the rubber insulaters that came with this servo because the ones provided were too small for my vehicles mounting hardware. But for the price I'm not disappointed. Shipping was quick. Ordered before noon & it was at my door in about 24 hrs via USPS using Amazon Prime. I'll update later after a few runs. UPDATE: Still doing great after a few on-road runs @ the 6 volts the BLX185 BEC circuit puts out. Upgrading to an external BEC for more torque & speed outta this. Even if I upgrade later to a quicker servo, I'll still keep this as a backup. UPDATE #2: The servo eventually failed because of the way I mounted it. My spacers between the chassis & the servo mount were not solid & that pressed the bottom of the servo into the chassis defeating it's waterproof seal for the circuit board. That being said, I will probably buy again. I have since upgraded to an aluminum servo mount & will use metal washers to adjust the height if necessary. Another update: I tore it apart and cleaned it up... It works. Now to see what it does on 7.4v. Yet another update: Now using in my Kraton 4sV2 that's a bit heavy with a larger motor, chassis brace & big tires. Also running it with an external BEC @ 7.5v it's working flawlessly. Originally was used without a servo saver in an Outcast 4SV2 & experienced no issues at all. Installed a servo saver in the Kraton 4SV2 & the servo saver couldn't keep up. Had to modify the servo saver with a heavier spring. Final update: Decided to run it on 8.4v with my Kraton 4sV2 that a bit in the heavy side... That was the final blow. I think it's dead now. But I've had this servo for a few years & tortured the hell out of it. I may still tear it down & check it out. But when it's disconnected, it turns easy one way & with resistance the other way.

Really an excellent servo upgrade for the Kyosho Fazer. Its a little taller, and the horn is thicker, but the servo is fast, strong and looks great. 100% recommend.

Had this on for awhile after I cooked my stock Traxxas steering servo (shocking ik) I was a bit hesitant but after abusing this thing as much as I could it's still kicking strong! If your running a trx4 I highly recommend upgrading your axle mounts to brass at the same time I thought I killed this servo but turns out I snapped a mount!

Does have plenty of torque but not as quick on the speed but I do recommend it for a replacement servo

Work great

2 out of 8 died after 1 hour of periodic useage at 7.4V; it was the motors in both. The motors were RF-130SH 21100 EDIT: 2 more died after 2 hours of useage at 5.1V; piece of brush came loose in the motors. EDIT 2: FeeTech support has been timely to my support emails :D

Can't complain.. a little squeaky but all the tourqe is there when needed.. ran through a bec for its full potential.

Great little servo ... but it is "almost" too big for the Traxxas TRX4M crawlers. I say this because I had to file the case down ever so slightly to get it to fit. But now that it is installed my grandson is delighted that his favorite RC car is back in service. The question now: Will it last longer than the original Traxxas servo ... which only lasted 30 days or so of more or less continuous duty at the hands of a 7- year old boy.

Buen servo.

With these budget servos, no need to spend this much, sb around $30 usd….don't buy.

No llega a 180 grados 120 tal vez