BTF-LIGHTING UL Listed FCOB COB LED Strip Light Warm White 3000K | High Density 528LED/m Uniform Light, DC24V 16.4FT CRI90+ 10mm Width for Home Indoor DIY Lighting(No Adapter or Controller)

Yeah these are awesome. I did a section of the "Christmas" light style, and took them down but these are super smooth looking. like a tube. If you get really close and are extremely critical you can sort of make out the individual bulbs, but these are as good as it gets for tape lights I think. The strips are super sticky and tough. the installation is a breeze. be careful to MAKE SURE you keep red with red and black with black. I swapped them at some point and it took a large effort to correct. Also get a transformer without a fan. I got the cheap one with the fan - sent it back and got the silent one. The fan in the bigger transformers is super loud. I did almost 200 feet of these in a single room. Did 4 loops with wire going back to the transformer so I didn't get a voltage drop toward the end of the loop and they are stunning! love them. I got the 500 watt transformer just to be safe. Im looking around the house for another place to put these. The color of these is perfect too, warm but not yellow and super bright. there is a slight hesitation when I turn them on, but that is not the lights its the transformer.

Very bright and nice! ONE ISSUE OF CONTENTION/CONFUSION: This is going to get a bit long and technical. Bear with me. I'm a noob when it comes to electronics and LED lighting. I'm trying to follow the best recommendations from various websites and Youtube videos, and it's taught me just enough to be dangerous. I'm going to tell you about a misunderstanding I had, in case you are prone to stumble into the same incorrect thought process. For this product both the Listing Title and the product Parameter Table say the 16.4 FT DC24V 336 LED/m strip needs 8 watts of power per meter of LED strip (8 watts per meter x 5 meters = 40 watts total). BUT THEN there is this little paragraph over in the right column in the "About This Item" section called "Power Calculation" which is written in a confusing manner and seems to say "8 watts per meter is not enough for this strip ... it actually needs closer to 30 watts per meter because voltage drop needs to be considered." At least that's how I read it. Looking at it again for the 15th time, another way to read it is "due to voltage drop, you won't actually end up with a total of 40 watts, you'll end up with a lower amount closer to 30 watts." But I took it the first way and thought it was telling me I need 30 watts per meter. And if that is the case, you would need 150 watts total (30 watts per meter x 5 meters = 150 watts). And then you'd want to increase that by a safety factor of 20%, so you'd end up at 187.5 watts (150 watts divided by a 0.80 safety factor = 187.5 watts). Due to this correction/recommendation/misunderstanding I purchased a 200 watt power supply (rounded up from 187.5 watts). But then when I received everything, I hooked up the LED strip, got out my multimeter, and measured the amperage draw: it was only 1.43 amps. Which means the LED strip at full power only needs 34.32 watts (1.43 amps x 24 volts). 34.23 watts divided by 5 meters = 6.864 watts per meter. So the amperage measurement I took with my multimeter indicated my LED strip was pulling even less than the "8 watts per meter" mentioned in the listing, and a *hell* of a lot less than the "30 watts per meter" I thought the "Power Calculation" paragraph claimed! What's my point? If you read that paragraph the way I did, don't worry about buying a 200 watt power supply like I did! It won't hurt anything, but it's WAY overkill. And if you need a dimmer knob, don't get worked up thinking you have to find a knob or switch capable of handling a minimum of 6.25 amps (150 watts divided by 24 volts) or a minimum of 8.33 amps (200 watts divided by 24 volts). You can get away with a dimmer knob that carries a max rating of 2.4 amps. It will work. According to my measurement, the strip only pulls 1.43 amps. And even when you build in a 20% safety factor, it only pulls 1.7875 amps (1.43 amps divided by a 0.80 safety factor = 1.7875 amps). Or if you work from the nominal "8 watts per meter" in the listing title, you only need 2.0825 amps when the 20% safety net is factored in (8 watts per meter x 5 meters = 40 watts; 40 watts divided by 24 volts = 1.666 amps; 1.666 amps divided by a 0.80 safety margin = 2.0825 amps). I know that was a lot of numbers and I hope I didn't lose anybody. But suffice it to say, don't get confused by that "30 watts" paragraph. It isn't saying "30 watts per meter." Base your calculations off of 8 watts per meter, add in a safety factor to make sure you're not maxing out your components, and you'll be fine. Get a 50 watt power supply. That's the one you need. For everybody who knew better, feel free to laugh at me. It's OK. For everybody who was confused like I was, don't sweat it. It happens. Buy this LED strip. It's nice. And pair it with a DC 24 volt, 50 watt power supply. The end.

LED lights were amazing addition to my kitchen. Easy to install and color was great. I connect these to a wireless remote control and worked great. Very durable and sticker is strong, I have not had any issues.

Honestly I was pretty surprised by the quality here I pieced together components to do under cabinet lighting and I used a dimmer switch in conjunction with these lights and you can see that they get plenty bright but you can control them down nicely to provide professional looking under cabinet lighting I put these in an aluminum rail mount with a frosted diffuser and can't be happier If I start having issues I will absolutely update this review

These work great ( as expected)

Very happy how flat & bright

Nice and bright!

It works pretty well but I would expect them to provide me with an angle connection or curve connection

I have used other types of ribbon LED before, this is far superior! I have used the type with individual LED emitters, the maximum density type, but still got "shadows" on the back wall. This has excellent "even" light, and is a great "working" light. I use it personally, and have great reviews from the other kitchen I have used it in now. It will now be the "go to" product for the foreseeable future! I used it inside of channel. In the past I have had call backs with cleaning "kitchen grease soot", I suggest you do as well. Especially near the stove. I mention this for this point, in past as mentioned I have used the "other" type of LED strip, when you put it in channel with a diffuser, the light is reduced so much, it takes away much of the "working light" aspect. it is still okay for ambiance, but not much else. This product does not have that issue. Using the channel & plastic cover will increase the longevity, as it is possible, to clean the diffuser!

I wish it was available in 1000k to 2500k cause that will look like golden rays of the Sun. What you see in photo is just a shorter part of a lengthy led strip. The other lengthier part is on the opposite direction of the room, which i cant capture while capturing this short part.

Great high cri lights, super soft diffuse light and easy to work with (highly recommend their solder free connectors). I saw some other reviews complaining about flicker: I myself also experienced that when dimming the first triac dimmer I had (that should technically be compatible, it was not visible to naked eye up any camera would see fast rolling bars. I just replaced the driver with the VEVOR 60W Dimmable LED Driver and that fixed the flicker issue.

Returned great product, was mistakenly ordered. What the heck Amazon??? I have to pay to ship it back now? This will impact how/if I shop with you in future.

Colour is amazing and brightness is spot on