Rockler Crosscut Sled for Table Saw with Adjustable Fence

This crosscut sled is awesome. It works great on my Ridgid R4520 10 inch table saw. The set up is a breeze and they make it very easy to get a .001 inch accuracy in seconds. Can you build a better one to suit your needs and probably be more accurate? Sure I'm guessing you can. But for the price, the accuracy and the ease this is well worth the purchase.

I got my sled today 8/26/19 set the sled up maybe took 15 minutes. Calibrated it on my table saw and did some practice cuts. I did a 90 degree 45 degree and even a 22 1/2 degree all were perfect. As i did these cuts I checked them with my digital level and angle finder. All three cuts were right on the money. The variance was very impressive within thousands. I do not think I could have built one with that kind of tolerance. Very impressive product. I will by from Rockler again. If there customer service is as good as there products this is a fantastic company.

This sled is a godsend! I've never had more accurate cuts. The inclusion of the adjustable miter, hold down clamp, and sliding stop is genius and makes every job 100 times easier and faster. It works great on my portable rigid saw, with a few addendums. 1. If the bottom of the hold down is not perfectly seated in the channel underneath, it can and will scratch the table surface. 2. It would've been nice if it came with a right-to-left reading ruler installed on the fence. I had to search for a while for one that was short enough that I wasn't wasting 4 ft, but long enough to span the fence. Not an easy find. This I believe is something Rockler could easily remedy. 3. This is probably the biggest gripe. While the sled works great on its own, the drop-off side is almost a must-have. For the high price, it should be included. The decision to sell it separately, by Rockler, almost smacks of greed. Otherwise, I am extremely happy with it and would still recommend it to hobbyist and pro alike.

This is a great addition to my table saw. It appears to be built a little light but time will prove whether it is adequate or too light.

Works great glad I bought it

I have made a couple cross-cut sleds, but with my new saw I wanted something that could function both for 90 degree cuts and miters. Like other things I have bought from Rockler, this is well thought out, solid, works great, and is just a little more expensive than I would like. I bought the drop-off sled, which for me is a requirement to get a nice zero-clearance edge. I made some quick adjustments by tightening the screws on the bars to eliminate play, and was off to the races. It works, it works fast -- if it holds like other Rockler stuff I've bought, the money is well spent. If you need a cross-cut sled and for whatever reason don't want to make one yourself, this is solid -- recommended.

A sled is a useful table saw accessory and Rockler items are usually high quality. I've got limited experience with sleds and this is a good addition to my workshop. I'm concerned that the MDF table may have moisture problems, since I'm located in Florida and my woodshop is in a converted garage. As expensive as this unit is, it would be preferable to have something other than MDF as the main element. For now, it's functioning properly, but I'm not ready to recommend it to others until it's durability has been proven.

Right out of the box accurate! After setting the tension on the miter bar and trimming off the excess off of the sled. I used the five cut method to check for square. Right out of the box it was -.00007937 /inch out. That’s crazy close! Didn’t have time to build one so I bought this one. Really happy with how accurate it came. A little expensive but still happy. Highly recommend.

Out of the package very easy to set up. I tested the 0 stop and it was +-1/256 per foot off. 5 cut 6" Perfectly usable and better that I could do to try and make it better. For those complaining about a right table, just make your own. 1/2 inch plywood and you are done. If you are purchasing this, odds are you have made your own xcut sled in the past. Cons. The Flip miter stop is useless. It cams to the right when you tighten it up and it has a > 1/4" gap at the bottom. Your best bet is to make your own right table with a miter stop. Especially since a left stop is not all that useful and you will be relying on your fence to make accurate cuts.

it’s cheaply made at a premium price, not as accurate as they say it is, if you tighten up the bearings in the mitre slots, it’s very hard to push, if you loosen them off then you get sideways slop