Front Bumper for 2013-2018 Dodge RAM 1500 (Exclude Rebel Trim) Pickup Truck Front Bumper Guard with 2 LED Fog Lights/Splash Guard Can Add 30” LED Light Fine Textured Black

Can’t beat the price. I have been trying to buy an ironman4x4 bumper for my Ram, but after months of it being out of stock, I decided to pull the trigger on this ironbison bumper. I am extremely impressed with the quality, especially considering the price is about a third of what the Ironman bumper costs. The powder coating and welds look great. I am more than happy with this purchase after being hesitant to buy this bumper because of the low price, assuming the quality would be poor. I couldn’t have been more wrong!

I needed to replace my 2014 Ram 1500 OEM bumper and I wasn't digging a lot of the of the aftermarket styles I was seeing. I didn't care for the under-bite look of most of them, reminded me too much of Bubba Blue from Forrest Gump. I liked the look of this one best, and I still think it looks good and I felt it was a fair price. Cheaper than a new flimsy OEM. This bumper is solid steel and heavy. It comes very well packaged. It's got a nice rugged kind of finish. I've had it almost 2 years and it has worn well. I think it is of good quality and I didn't have too much trouble installing it, but a second pair of hands helps, especially aligning it to the body panels. But as others have stated, you'll have to figure out wiring up the fog lights. They do include their own separate wiring harness for the lights which includes a switch you can stick on your dash or steering column, but not really the cleanest installation. And of course you'll first have a bit of wire routing to do through the firewall. OR, you can just snip off the plug ends from the old OEM lights, splice onto the new lights and just plug it into your existing harness. This is what I did. BTW, the fog lights are pretty bright, they light up that section of road directly in front of you very nicely, but you'll have people occasionally flash their brights at you. Just make sure you angle the lights correctly and check periodically that they haven't loosened up. That should satisfy all but the most sensitive drivers out there. I really wanted to be able to give this bumper 5 stars, but 2 issues held me back. 1. I wish the skid plate was a bit larger and hung lower or angled differently. It's an aesthetic thing. 2. The fog lights cause some interference on certain radio stations. Not a deal breaker for me, but it's something to consider. I either change stations or turn off the fog lights. I tried clip-on ferrite EMI noise filters, but it didn't help much. At least that's what I've experienced. YMMV

Fits perfect and looks nice but light pods went out after a hour of use

This product really met the need for me. I had an option to replace the OEM or save some cash and buy this product. Today I received the bumper and was initially impressed with packaging. All was packed tightly in foam and all hardware logically separated and sealed. The instructions were very clear. Despite having watched a few videos beforehand I still ended up referencing the instructions. They were complete with photos and quick and easy to follow steps. I started and assembled the bumper first, I would recommend. Once the whole thing was built I attached the lights and zip tied the pig tails to the bumper. With an extra hand we removed all 6 mounting nuts and bolts. Tip: if you remove the bumper to trim fascia and headlight plastics first you can remove most from above in clear sight. Once the old was off we easily installed the new. We installed it just finger tight and then put the grill and headlights back in, made sure our bumper adjustments were set then tightened the mounting nuts down. Finally I clipped the wire pigtail from the OEM fogs behind the Y in the line, that way I still had wires available for the new fog leds. I then used some solder sleeves to hook up the lights to their respective pig tail end from the OEM plug harness. I covered those in some heat shrink and then took my new clean bumper harness and plugged into the OEM clip. This way there is no need to wire to battery and run an extra switch blah blah blah. Easy peasy and the new LEDs function like the OEM lights. Simple install, very clean, great welds and powder coat all around. Even down to the thoughtful slip spacers on the internal bumper nuts. Each receiving threaded hole on the bumper was greased as well. Like just everything you could hope for when opening a steel manufactured good. Buy it, you’ll love it

I made the mistake of buying this for my 2018 ram rebel 1500! It actually fit and lined up but I had to make some adjustments and go away with the upper trim pieces. It looks good also wiring the fog light to previous fog light harness

Overall pretty good bumper. Somewhat easy to install. You will need two people to install it. The only downside was that the wiring harnesses for the new fog lights do not match the OEM harnesses so you will need to do some fancy wiring yourself. Overall pretty good.

Bumper came with bad threads on one of the wing holes and the side pieces that go under the headlights don’t line up good with either the lights or the fender if you put them close the the fender it’s leaves a huge gap with the headlights and if you put it close to the headlights it leaves a huge gap with the fender

excelente producto, queda exacto, como de fábrica y cambia radicar el frente de la guagua

In the process of installing and the trying to install a Auxbeam Led Strobe Light Bar 30 inch. As you can see its 2 inches off. Sadly, IronBision Website also states its a 30 inch bar, so I do not fault seller. Making come custom brackets to make the light work. Also, if you to keep the grill in front of the light bar, likely going to require some grinding, as the mounts for the gill get in the way of the light bar. I want grill to protect the light and think the Amber option on the light would look good through the grill.