Chemical Guys, Headlight Restore & Protect, Clears Cloudy Lenses, 16 oz

I've been using this product for a while, but have never written a review. This product does work, and in the world of "Polishes" and trying to figure out which grade or grit you need, this is nice cause it's just the right grit rating to do a complete job relatively easily. To Start: PREP0: Open the hood of our car or truck, that ensures you get the best access to the headlight lens, including the top. PREP1:Obviously make sure the lens is clean, which you can do just using window cleaner or after you washed the car or took to the car wash. PREP2: You want to remove the first line of "Haze" here's a trick, use WD40 or Ballistol.. Simply spray it onto a microfiber cloth and wipe down, you'll notice it takes off a layer, but not ENOUGH to make the lens clear, but it DOES help and sort of "Pre lubes" the surface a bit. ---Note -- IF the lenses are severely oxidized, like it's very rough and pitted to the touch, and almost completely faded out, you may need to do a wetsand prep using something like a 3000/5000/7000 grit sandpaper, THEN start the Chemical Guys' polishing routine with this product. This product won't remove that harsh first layer of oxidation, or it will take forever, as it's a very medium to medium fine polish. If you have to wetsand first, use a spray bottle of distilled water, wet the lens thoroughly, then first go with 3000 and work up to 5000 and maybe 7000, constantly lubing with water and wiping off the excess with a clean towel. After you go through the 3 stages then apply this Chemical Guys' polish routine. But, for most people they won't have to do this. But if you have to do this, prep3 is critical below: Masking. PREP3: TAPE: It's best to get some blue or green painters type masking tape and tape off the light from the painted areas of the car. Don't over think it, it's not like you're painting anything, you just want to mask off the painted areas from the headlight to keep the bonnet from bumping the paint. And from the material getting into areas you don't want to.. PREP4: HAND POLISH: If you're using a foam bonnet or a microfiber bonnet (or a towel) this will take longer, but you have more control of the "product" and it doesn't fling off. Simply put some on your foam bonnet and polish it in. Keep working it, and sometimes you can have a spray bottle of water to lubricate it a bit, and continue to work it in. Wipe it off, try a second coat doing the same procedure. Remove the tape, Let it DRY, then use a clean cotton cloth to remove the excess.. Cotton will not create the static like Microfiber does and it won't remove any protect layers of the product, leaving it treated, as this Chemical Guys' headlight restorer does have a UV protectant in it. If you don't have a cotton cloth, that's okay, just don't press too hard, just lightly buff it and remove the haze.. Voila.. Clear. PREP4A: MACHINE POLISHER. If you're using a rotary polisher, whether it's a large bonnet type designed to polish, or a smaller one, like a special tool that holds a 3" flat bonnet, or a smaller bonnet (Like the ones you use on Drills, the round type) you have to be a little more careful applying the product as it'll fling off and make sort of a mess. So you put it on the flat or round bonnet, spread it around on the bonnet and the lens and SLOWLY work it in, don't go full blast or you could possibly burn the plastic or the paint surrounding the headlight.. So you want to be careful not to hit the painted areas. HENCE the masking. Work it in slowly, and then gradually increase the speed.. You don't have to press real hard, as that just makes the bonnet lose control a bit.. Just a nice light pressure and allow the rotary device to do the work. Also, you can rest assured your polishing bonnet has probably absorbed some of the material, especially by the time you get to the 2nd headlight. That being said, you can continue to polish a bit without having to apply more product. This product seems to not dry too quickly and has a slight oily texture to it so you can work it in looking as though you don't always have to have a fresh "Haze" of the product on the light lens.. Again, if the bonnet is fairly saturated with product you should be good. Again, like above, you can also spray some water on it and continue you on that way as well. Be sure to avoid hitting the painted masked areas as much as possible, bumping them slightly won't really hurt it, but when you're increasing the speed just be sure to avoid them, you don't want to "burn" the paint. Remove the tape, let the product dry to a haze, and slightly wipe clean with a cotton or microfiber towel. Tip: I buy high quality paint brushes, like 2", 3" wide, the stubby kinds, which are great for after a procedure like this to wipe around the light lenses, to get any chalked product out. If you have an air compressor that's a bonus too. Just use the brush around the edges, then hit it with an air compressor.. Should look great. Like these: https://www.amazon.com/Wooster-Brush-Q3211-2-Shortcut-Paintbrush/dp/B099KL78FB/ref=sr_1_6?dib=eyJ2IjoiMSJ9.SUZ3kYDsniTGpWjAgfwOX1LQJ_Yq8wMpc0b83Zaw7faaGpmqa2xEHA1lQlXw8WCpNNesowQGa4tnPmKzSFUxH4WeQ-PxOS2JiXDG5OTNhlJEeCY26NFkoXBmclsJqhfi_V40EU8qRkS1Ma1pG7dJj_YrBToUPaKAtvF_K_rStd0c9Nw1bx6ZzDcodmc5RYwWr35jsUugVCnPN4B1GPu0DDxfKqTf9zxIzakWAGvtjGiZbORcA_bS276zEYyIe-AowBrSuZC0KrZ29lePdIzQagGLolWCuvOC7LTBLINBWe4.wRl7tSfIBoecdoW846dL8XItJGA-99c2tpA8mgHC09c&dib_tag=se&keywords=stubby+paint+brushes&qid=1733415295&sr=8-6

I recently tried out Chemical Guys GAP11516 Headlight Restore and Protect, and I must say, I am thoroughly impressed with the results. This product truly lives up to its claims and has exceeded my expectations in every way. First and foremost, the professional-grade restoration provided by this headlight restorer is nothing short of remarkable. With just a simple application, the advanced formula effectively removes the faded, hazy appearance of my headlights, revealing the pristine plastic beneath. The difference in clarity is astonishing – my headlights now shine with the brightness and clarity of brand new ones. What sets Chemical Guys Headlight Restore and Protect apart is its all-weather protection feature. It's not just a cleaner; it's also a protector. After restoring clarity, it seals the surface, safeguarding against harmful elements that cause yellowing and oxidation. This ensures that my headlights stay clear and vibrant for longer, even in harsh weather conditions. Perhaps the best part about this product is its cost-effectiveness. Instead of shelling out money for expensive replacements, a simple DIY with Headlight Restore and Protect rejuvenates and maintains my headlights, saving me both time and money in the long run. But the benefits don't stop there – safety is also a top priority with this product. Improved visibility means safer driving, especially at night or in adverse weather conditions. Regular use of Chemical Guys Headlight Restore and Protect ensures that my headlights remain clear, enhancing my night vision and overall road safety. And let's not forget the ease of use – applying this product was a breeze, even for someone like me who is not particularly skilled in car maintenance. Plus, I've been using it for several weeks now, and I'm thrilled to report that my headlights have held up beautifully without any signs of yellowing or deterioration. In conclusion, if you're looking for a reliable and effective solution to restore and protect your headlights, look no further than Chemical Guys GAP11516 Headlight Restore and Protect. With its professional-grade results, all-weather protection, cost-effectiveness, and ease of use, it's no wonder Chemical Guys is the go-to brand in car care. Trust me – you won't be disappointed!

My headlights (2006 Corolla) were not as severely yellowed, as many I have seen. There were some rough patches that diffused the headlight beam. In the past, I used plastic polish that required a lot of pressure and time to clean by hand. The Chemical Guys headlight restore is a good product and is basically a compound that abrades the oxidation on the headlight surface. I decided to use strong hand pressure with a microfiber cloth. I removed the majority of the oxidation and the headlight surface appears nearly new. My recommendation for badly oxidized headlights is to use a polisher or a drill with the proper polishing attachments. This Chemical Guys restorer is a good product. It is not a miracle product that you wipe on and the surface is instantly renewed. It does require time and effort if done by hand. The proper polishing tools with a powered tool is recommended for badly discolored lights.

I rarely write reviews, but I have been disappointed by so many headlight restoration products that I felt compelled to share that THIS STUFF REALLY WORKS! Frankly I was skeptical, but since most Chemical Guys products that I have used have lived-up to their hype I decided to give this a try. When I read the directions and saw that sanding might be required for the worst case headlights I thought "Yep, here we go again!" I tried this product on a 2015 Lexus SUV, a 1998 Porsche Boxster, and a 2004 Chrysler Crossfire. It produced dramatic results the first try with each vehicle, and in the case of a truly hazy headlight, the second application finished the job perfectly. It did not take a lot of heavy scrubbing or buffing, and produced equally good results when applied by hand and with a machine buffer. I am a car guy and somewhat obsessive about clean well-detailed cars. There might be some headlights that this product won't restore, but it sure as heck worked on mine. I highly recommend giving it a try! And - NO - I wasn't compensated for this review in any way.

Product made my headlights look new and crystal clear in seconds. My lights were maybe 35% clouded. Rubbed a few drops vigorously over about a 10” square area until the product turned clear and started to dry took a second cloth and buffed lightly to remove excess. I have a dodge with large headlights so I repeated the process 3 times to get the whole light. Change the portion of your rubbing applicator cloth each time because it will become clogged with the removed damaged layer of plastic. I recommend masking the surrounding surfaces to prevent any possible damage from any over wiping or drops even though the whole process is simple and was very clean. I was very pleased with the excellent results and could do this to another five vehicles or more with what is left in the bottle , which makes the price of purchase well worth spending. Definitely a permanent addition to my detailing chemical supply list.

Works great clears the scratch's and fog instantly, however it does not last beyond a car wash? I am using micro fiber to apply and clear once the polish has fogged.

I was extremely surprised how well this product worked. I have a 2010 Highlander whose headlight covers were practically opaque. I tried other products that provided multi-step procedures that had little or no effect on the plastic. When I saw this advertised I took a chance and ordered it. All you have to do is apply a quantity of the product and hand scrub it in with a soft sponge or cloth. As it starts to dry just wipe it off with a clean cloth and the magic happens. I don’t usually write reviews but this product is a 5 star winner.

I have an 11 year old truck that is beaten by the Texas heat. Headlights were hazed and I was pricing replacement's which would have cost several hundred dollars, even more if I went with OEM. Tried this as a last resort and glad I did. It took an about 5 passes but lights are significantly better. I wish I would have taken before and after. I may try it on my brothers truck and if I do I’ll submit photos.

Realmente es magnifico, sin usar taladro o set de lijas deja un acabado espectacular.

Okay... so you've been surfing for a headlight restoration kit, and you see all these products that want you to do all kinds of sanding and polishing to restore your headlights. I have used a kit like that before--and it does the job. However, it takes a lot of work, and if you're not careful you can damage your headlight lens. I wanted something that could be used without sanding, and I ended up here. The process is dead simple... Put some of the product (which has a creamy texture) onto a microfiber cloth or similar, and then rub it on the lens. Once it has been worked in, use a clean cloth to remove any excess, and to polish the lens. Total time is 5 minutes. I'm attaching images from two vehicles I treated. One is a Ford Freestar (2007), the other is a Honda Civic (2009). I literally spent 5 minutes on each lens. If you have a buffer, that would be handy, but it's not essential. I did this on a sunny day, so that the lenses would be 'warm'. While I don't know if it matters, it certainly doesn't hurt. What I did notice was that the product worked best on lenses that were physically smooth. It's hard to see in the images, but the Freestar lens had more 'abrasion' marks, and didn't clean up as well. The smoother the lens, the better the outcome was. So if your lens has a lot of scratches on it, the performance of the product may not be as good. As for longevity, I have no idea, since I only did this a couple weeks ago. However, I've driven in the rain, and the lenses are still as good as they were when I applied it. In the end, it was certainly worth the money I spent for it--if for nothing more than the convenience of not spending a couple hours sanding my headlights. This is not a product for someone who wants 'perfection' though. The result is very good, but I suspect a kit with sandpaper would be able to get them 10% clearer. However, if you just want to get your lenses clear, you'll likely be happy with the performance of this product.

good

A perfect magic product it clears the headlights like a magic.

good product