BEAMTECH H7 Light Bulb, 6500K Xenon White, Fanless In Line, 1:1, Pack of 2 | No Adapter Need, Small Size Design, 1:1 Size

Just a preface... I am using these in my 2017 Honda Accord EX-L Coupe for low beams only. I already had LED H11 Headlights previously installed 2 years ago.. I believe its chip controlled so you can jut swap out the halogens...but...READ YOUR VEHICLE INSTALLATION AND PLUG SUPPLIED INFO FIRST. You may need a new LED capable wire harness and/or plug. I did not. At any rate, the search for these 25W each H11 LED's at 6500k (kelvin, or brightness color) was relatively painless. I saw a set with lots of buyers and reviews from a company called BEAMTECH. Again, they have great reviews, the product looked to be exactly what I needed and the price was right. I ordered this set right then and there. My passenger side LED blew and was unusable. Upon ordering I knew I would replace both sides for a perfect match (and to keep all voltage compatible). I received my package well padded within 2 days with Amazon Prime, as usual. After receiving the item I inspected it and HOPED this would be a straight replacement (would fit the adapter I currently use). I also hoped that at 6500k (the chosen white color) it would match what I previously had in there. To my great delight, IT DID! The following day I set out to do the installation myself, I'm OK with replacing bulbs, air filters and such. I know a little bit about cars. I popped the hood on a hot, humid 85 degree morning. I knew where the proper plugs were already so it was only a matter of removing the old one's first (5 Mins.) Next I opened the new LED's box and once again was very pleased with the quality of the unit and the packaging. The wiring harness was the exact match from old ones to new! I then installed both sides(5 Mins.). Check the operation of the new LED's first BEFORE mounting and inserrting them back into the headlight fixture. I checked and left was on but right wasn't. No big deal there as I already knew LED's ARE polarity (positive & negative) specific so if the LED does not turn on. Just have to reverse the harness plug and bulb to set the polarity correct. VERY EASY. BAM! They both turned on, looked GREAT, AND matched all the other LED's I have installed (fog lights, running lights and high beams are all LED). After mounting the new bulbs back in the headlight enclosure, I was very pleased. They fit perfect and looked great! After the install I lowered the hood, turned on all of my headlights, fogs, and rear again. It really matched perfectly and even drew a clean beam output perfectly on the road. So all in all, tops a 20 minute job! Saved a ton of cash doing it myself too. I then packed everything back up, shutdown the car and back into the AC I went. I want to tell you this...I am so happy beyond words when a plan comes together as easy as this did. I knew I could get pulled over and get a ticket for something this trivial and wasn't willing to take that chance. I barely broke a sweat. So hats off to you BEAMTECH, you have another happy customer! GREAT PRODUCT! Will definitely recommend and come back when I need more.

I was shopping around for a better lighting solution for my 2015 Toyota Camry and stumbled upon this little gem. At first i was pretty spectacle as led lighting for a front facing main light was a new concept at least for me. I looked at the pictures posted by other reviewers and decided to order it considering that at the time of my purchase, the advertised price was only $34.99 per pair which would not break the bank, considering that certain halogen ones that come in a pair at any auto parts store are comparable in price if not more. i was super excited to receive them and was very anxious to try them out to see what all the fuss was about led technology. In my case, i got the H11 bulb which did not require any modifications or cancelers and install took about 10 seconds per side. The light is super bright and a great addition to my projector beam headlights which evenly distribute the light in front and in comparison, the halogens just couldn't cut it. The lights do not bother oncoming traffic and / or raise any kind of codes in the dashboard in my particular case of the 2015 Toyota Camry which have non adjustable beam pattern. I initially wanted to do a side by side comparison but as soon as i installed the light on one side, i just could not resist doing the same on the other side as well and then saved the halogens in the beamtech box itself tucked away in the trunk as backup just in case the new led lights go out. So far i like them and they look very similar to factory installed lamps. Unlike HID lights, these LED lights are instant on every single time and do not pulsate or flicker to cause any distraction or irritation to the eyes on the highway. One thing to note however is that led light is projected differently on different surfaces whether it be a wet roadway or the rear bumper of the car in front of you. In my drive time testing, i noticed that certain paved streets appeared brighter and other city streets and highways comparable or less brighter than regular halogens. Also, i noticed the led light projected on two separate black colored vehicles at night time exhibited very different results with one appearing fabulously brighter than normal and on the other car, it almost felt like my headlights were dim and about to go out. This could be the result of the kind of paint or finish the vehicle or the roadway may have and how well the human eye adjusts to changing light conditions. So far, i have not encountered any issues the performance or with visibility and i am very happy with this purchase. I know that further testing may be required but currently, i like it and would recommend it others as well.

I’ve had a set of Supernova SV4’s in my F150 for a couple years now, spent over $300 on them, less than a year the passenger side diode went out, which was really disappointing, so I emailed the website I originally bought them from, they were great and sent me a new bulb free of charge, the problem continued though as the drivers side diode went out a few months later so I emailed them again and they sent me ANOTHER bulb free of charge which was very unexpected and appreciated. With that being said it’s been over a year now and the passenger side bulb is starting to go out again so I got to thinking… when I initially bought those $320 LED’s I also bought a set of $25 Beamtech fog lights and those were STILL RUNNING AS BRIGHT AS NEW to this day! So I decided to go on Amazon and see what type of low beam bulbs Beamtech offers and I stumbled upon these… a fanless, compact, easy to install in-line bulb that doesn’t need a canbus, so I took the risk and bought them, I figured these are only $40 so they can’t be THAT bright and probably have a really shifty beam pattern, but if they don’t work out at least they didn’t cost as much as a car payment. So I put them in, installation was a breeze, build quality is top notch and they pack a little weight to them which was encouraging, the fit was perfect into the H11 housing too. I waited until night to go for a drive and WOW!!! These are absolutely OUTSTANDING!! I would have never guessed something this small with no fan could be SO POWERFUL AND BRIGHT! These are almost just as bright as my SV4’s lights, beam pattern was SPOT ON, no hot spots and absolutely SILENT. Can’t beat it for this price. If you’re stuck between these and another brand, I would HIGHLY recommend giving these a shot.

I bought both the 9003 and the 9006 for my 2005 Toyota Tundra. These are excellent bulbs, but there's a few things I didn't find covered in other reviews. First, the high/low 9003. No one really explained this, so I will. The bulbs are removable from the locking plates. You install the plates into your headlights, then slide you dust covers on the bulb, then they push in and turn to lock into the locking plate adapters you previously put into your housing. This makes for a simple weather proof installation. The only thing is, the bulbs will push in and lock into the adapters right side up or upside down. I got both of mine in upside down the first try, and the beam looked funky. Easy to tell when you flip from high to low and back. I rotated the bulbs 180 degrees in the adapters and they now are perfect with an awesome beam pattern in my housings. Five stars for the 9003. Now for the 9006 bulbs. These are a replacement for my fog bulbs. There are three things that need to be addressed. First, the polarity of the plugs were reversed for my Toyota. I had to flip the pins in the plugs. Second, they do no lock into the housings very well at all. They were loose and rattled around. I was afraid they would eventually turn and fall out while driving, so I had to make shims to tighten them in the housing. Third, fog lights have a very directional housing, and the bulbs are clocked 90 degrees off. I was getting very low output at first, but once I realized the LED was not pointed correctly in the housing, I found the bulbs are actually a friction fit in the adapters, and could be rotated until the LED is pointing through the reflector opening in the housings. Because of the fiddly fitting and reversed plugs, Three stars for the 9006. These would have been five star lights IF they fit the housings better and it was explained in some fog housings you would need to clock the bulbs for proper output. Now with all of the adjustments and fitting done, both the 9003 and 9006 are excellent. Pure white and very bright. They put my previous Sylvainia Silver Star halogens to shame. No more yellow light here. All in all, these are very white, bright, and high quality bulbs. I really like the fact they use a high quality heat sink instead of a fan, too. Fans fail, heat sinks don't. I just wish the directions for fitment and adjustments procedures would have been more clear. Also, these have only been in a couple of days. I sure hope they hold up to the Florida heat and weather. If they do, these are unbeatable for price and quality.

Truly a great set of bulbs - compared to the halogen bulbs that came in my 2013 Malibu (which were decent) the difference is night and day! Most of my driving is done at night so I usually upgrade to LED anytime I get a new vehicle and I'm glad I did. Very good quality of bulb, and above all else.. a company that stands behind their products! Very bright, installed in less then 10 minutes! I started having a flickering issue with one of the bulbs just prior to a year after buying them and after just a couple messages explaining my issue they sent me a brand new set. I highly recommend these bulbs if you are in the market, you certainly will not be disappointed!

Original review: I wasn't able to get this to completely install on a 2014 Acura ILX while retaining use of the stock dust covers. The lights functioned and looked nice, had a clean cut off. 3 stars because of the products quality. What would usually be metal on a Sylvian bulb was plastic here and not the best quality. (probably from "no-look" attempts at installing for 5 minutes or so) Installation was easy enough, plug and play but if moisture or water enter the headlight housing you're going to have more problems that just having a yellow headlight. I did get a replacement dust cover, but on my vehicle the bulb location isn't centered around where the dust cap goes on and every dust cover replacement has the hole centered. There isn't sufficient space to place a bulb type cover on either. Even if the headlights were removed entirely, I don't see there being enough space behind the bulb to be readily serviceable. BeamTech was more than happy to help me getting a replacement dust cover but at this point it's more trouble than it's worth. In the totality of circumstances, I would not recommend this product for a 2014 Acura ILX with projector halogens. Update 6/23/18: The seller (Beamtech) is really committed to getting this to work out. I've had something like 6 emails with them trying to get it to work on my car. Also, (from reading other reviews) I'm not the brightest when it comes to things. The part that screws on is plastic so it doesn't scratch off the chrome lining where the bulb goes in while you're "no-look" trying to screw it in there for 2 or 3 minutes. Now that I think about it, if it were metal I would have scraped that all off. I attached a picture (not of my headlight but the same one) of what I mean when I say it's off center. Update: 10/2/18: After this sat in my garage for some time, I decided to give this another attempt. I did end up finding a dust cover that worked to my satisfaction (https://www.amazon.com/gp/product/B075SBDGVN/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1). I had watched quite a few videos on different variations of LED headlights and this particular kit had come up as one of the best "sub-$100" kits. That said, make sure you are installing this correctly. That the bulb faces the same direction as a stock bulb is very important. You may think you have it installed but if the bulb isn't facing the right direction you're going to have a significantly lower light output down road. Update 8/26/19: I've had these on the car for about a year now and have had no problems. I would recommend this product. The driver and everything is built into the bulb so there isn't a ton of excessive wiring and parts jumbled into the headlight housing. I've never heard it make any noise in the cabin and it doesn't interfere with the radio.

To start off, I've used Beamtech bulbs for the last 8 years on all my vehicles, including my Aston Martin. They've been solid for me up til this current issue. The issue, I installed these on my 21 Ranger (see photos) to color match my sequential DRL's that are 6500k. Keep in mind to change the bulbs on my truck the entire front end needs to come off, and the headlight housing need to be removed (see photo 2). The first batch lasted about 1k total miles, including day and night driving. So the bulbs were on less that half of that time. They failed, I reordered then replaced them. The second batch lasted around 3k total miles. Maybe a 3rd of those miles were at night where the bulbs would be in use. The failure I've experienced with both orders is shown in photo 4. The correct functioning example is shown in photo 3. What happens is the bulbs have two smd leds, one on each side. One of the bulbs keeps going or, or will flicker. This decreases the light output to half and mimics a headlight being out when inside the cabin. If you go inspect the light outside the truck it looks fine because one of the leds still functions causing it to stay lit up. I've circled the dead smd led in red in the 4th photo, compare it to photo 3 and you can see the difference. This has now happened twice. On the first batch the driver side bulb failed, on the second the passenger side. Keep in mind the intensive labor required to change these for such a simple failure. Due to the issues with these specific bulbs I think I will be looking for a new brand. If things are made right I will update this review. For reference I build custom cars for a living and have a extensive collection of my own as well.

Great quality have in all my vehicles great for off road super bright the only lights I will be buying

Muy fácil de instalar (me tomo menos de 30 min), y no presentó ningún testigo en mi en mi auto. Se nota muy buena calidad de materiales y alumbra tal como se podría esperar, se puede decir que tiene muy buena relación calidad-precio. Espero en durabilidad también cumpla con las expectativas.

Installed a few months ago and the quality is great. Was worried the colours might be too much on the cooler blue side but it’s perfect.

Bought this for my 2021 Subaru crosstrek, the stock halogen bulbs were really bad. Today is day 1 and using them for my low beams. Its very easy to install and has a good beam pattern. There are no fans or external drivers to deal with like many other led lights. It gives off a blueish light which is exactly what I was looking for. I lights up down the road very well without it being extremely bright and blinding other drivers. I read that some LEDs cause interference with the radio but this one didn't it was straight plug and play and very easy to install! Would recommend if you want to upgrade your lights but not wanting to blind other drivers. Amazon said this light doesn't fit my car but it did because I knew my bulb was a h11 so I just matched it with a h11 led bulb.

These work well enough in my 2013 Fiast 500. The one problem is that the LEDs are cannot be rotated - so if your socket places them in any position other than horizontal, the placement is suboptimal. I did a fair bit of testing on my projector housings and dialed in the alignment; there seems to be no off-axis glare produced by having the LEDs off-angle, hence why I'm only docking one star. They're plenty bright, but not blinding to oncoming traffic, and provide enough light to see by at night. High beams are extremely bright (again, make sure you align these well!) and when I flash a driver who's forgotten theirs on the response is appropriately quick.

I love the Outcome on these LED Lights, Better version than Halogen lights. I can see clearly at night on Highways.