Pack of 5pcs 12'' Short Adhesive Table Sticky Measuring Tape | Self-Adhesive Tape Measure Read From Left to Right (Inches)

These tapes are a total steal for the price. The numbers and lines are really clear and easy to read, which is helpful when you're in the middle of a project. I stuck them above the keys of my laptop and they don't peel up at the edges at all. If you’re looking for a cheap and easy way to stay organized, go for it. I got one for my family too. It has inches at the top and centimeters on the bottom. Con: It's not that thick for those who care about that but it serves its purpose perfectly fine for me. Quality overall is great.

Sometimes you need a ruler that stays with what you’re measuring. That’s what I got this for. It’s thin enough when installed that you can put it on something that gets rubbed without it catching. The adhesive works well, and the backing comes off easily so it’s easy to apply. The tapes have the dimensions advertised, so they do the job well

This has is a decent zero center tape, the measurements are mostly accurate although there is about a 32nd of an inch disparity over 12 inches on either side when lined up against a known accurate measuring device (red expensive 🇺🇸 USA MADE rule that is named after a bird). The adhesive quality is questionable and time will tell. The tape isn't thick and shouldn't get caught on anything easily, though time will tell for that as well.

I used this to put gradations on a jig I made to measure the inside diameter of whisky barrels at various points. I'm cutting circles with beveled edges to fit exactly in the barrel, so needed accurate readings. I cut the tape strip down the middle and stuck the Imperial scale on one side and metric scale on the other. They stuck well to the smooth maple sides of the device. I was disappointed that the Imperial side only measured to the closest 1/8", so I used the millimeter side for greater accuracy. I put another of the strips on my circle cutting jig so they were both using the same scale, and in the end it worked very well. Some of the other reviews showed much smaller gradations, though the actual ad truly shows them in 1/8" increments.

Great product

I have an older Jet bandsaw. Bought the Carter Magfence II, but wanted some way to ensure it was parallel to the blade. Bought a couple of these adhesive measuring strips, installed them on either side, and the result exceeded my expectations. By buying these "start from middle" kind, I didn't have to worry about buying a "right to left" and a "left to right" piece. AND I now have measurements on BOTH sides of the blade. BIG NOTE: The description is vague, and makes it seem like they are only 12" long total (6" on each side), but these tapes have 12" on EACH SIDE of the zero, so each piece is really 2 feet long! This makes them a LOT more versatile and even more perfect for my needs (I needed about 8" on one side, and 6" on the other). Also, they are indeed a matte silver, even though the pics make them seem almost white.

I have these stuck all over my woodworking tools. They stick; they stay. They are sturdy but thin enough to have tools slide over them. Examples: Mitre saw, router table, table saw. I've bought them twice, but I think these are slightly better than before. And you get more in the order. Highly recommend!

So I had to login and recheck to verify I didn't accidentally click the incorrect version for my project. A co-worker did point out not to click the CENTER-OUT version, which I am very thankful for that. However, when I opened the little plastic package, I noticed these were printed right-to-left instead of left-to-right like the photo shows. I figured that since there was 5 included, maybe I got a mix-and-match - which I did not. I can use these on the opposite side of the board I am making, but I need left-to-right for the other side. Once laid out off the backing paper, these were measured and showed very accurate to the 12 inch mark.

Didn't put a tape measure to it for verification on accuracy, but they hold up great.

arrived earlier than I expected. I use it with my little hobby cutter and it's just fine, Thank you JPLattes

Pour mon établi de travail

I used the tape to make a thickness guide for my slicer. Worked perfect. Stuck well and easy to read.

I was really happy with these initially. I purchased them for my table saw fence measurements. It worked great for awhile but then peeled off. They are expensive at 8.99 per measurement and I needed front and back with the zero in the middle... So I won't replace them at $20 a set.. I will find other alternatives, it was great but so disappointed that they peeled off.