Kreg KMA3700 Accu-Cut XL - Universal Track Saw Guide System - Cuts up to 100" Long - No Clamps Needed - Make Straight, Cross, Rip & Angled Cuts Easily - Circular Saw Guide - Woodworking Tool | Universal Track Saw Guide System, No Clamps Needed, Make Straight, Cross, Rip and Angled Cuts Easily, Cuts up to 100" Long

Worth the hype. We are thrilled at how well this works and has become a critical part of our construction toolkit. Awesome for when you dont have easy access to a table saw

So much easier than getting that first plywood cut on a table say, even with help. The zero clearance edge makes set up fast. I don't even draw a line, just two measured dots and set the edge there. Drew a line and flipped it around for a second line to check the straightness in it as off 1/32 at the middle. Nice. It actually does stay put without clamps like the video. The aux clamps might be nice as the rubber ages, but so far so good. I store it in 4' sections on it's own shelf. The 4' length still stays put for those plywood cuts.

Craig always knocks it down at the park and it was cheap enough.Not to break the bank. just mount your favorite saw to it.And get a perfect cut every time.

Pretty good. Can use some Drawer tape to get the slide to snug-up to the rails, once this is done you get VERY straight cuts. YouTube Videos are out there showing the process. Trimmed out windows with it, zero gaps. Would recommend.

The Kreg Accu-Cut works better than expected. I get clean cuts of plywood with no splintering and perfectly straight cuts. This is a great addition to my cutting tools.

I got this to brake down full sheets of plywood and to rip a straight edge on rough cut lumber. It comes in handy to make large angle cuts also that I can't do on my table saw because of space and safety reasons. I like the way it breaks down for easy storage and is so quick to set up again when needed. I made a hold down clamp to hold the far end down so it will not shift when making long cuts. For short cuts you can get away with out clamps But if you have them its always better to put them on. I have even used it to make cuts when I had my table saw set up already for another project but then needed another piece of plywood cut down to a smaller size. It's well made and I like the start base to set my saw on after I have made a cut. It helps to keep from marring your stock from setting the saw on top after cutting. The good thing is after you get it you don't have to keep buying things to make it better it's a complete package Track saw base and clamps then you are done. You wont go wrong with this one.

I am SO glad I bought this track. Building cabinets I finally have highly accurate cuts across long sheets.Many complain about 1.) sled slop/wobble, and 2.) track alignment.1.) add a thin strip of low friction tape ($5 on amazon for 5 yards) to the sides of the channels on the bottom of the sled where it makes contact with the track. Instant no slop smooth movement.2.) align with a quality aluminum 6ft level. Have another person help hold the track pieces tight to the straight edge while you tighten the set screws. You really need a third hand for this, & it turns out perfect with no issues. Slightest amount of loosness while screwing set screws will result in a small gap & inaccuracy,I do wish the set screws used an Allen wrench instead of philips screwdriver, but use a#1 size Phillips & you won’t have an issue.Great track, so happy with it!

I bought this because I couldn’t afford a table saw. But WOW. This is so much safer than fussing around with a sheet of 4’x8’ plywood on the deck of a table saw. It doesn’t fill all the needs so I did eventually get a table sawThis is a quality tool. A lot less expensive than a Festool which we used at work. Pretty much just as good. So get it. Get enough pieces to do the work. Label the underside of each. Find a create a safe place while not in use. I paired it with a Makita 8” radial saw. And a really nice blade.

Works great love it easy to put together easy to use. The only issue I had is just for the type of thought I have it doesn’t clamp 100% perfect onto the slider just because of the type of base it has but other than that I think it’ll be fine with any other saw it could have adjustable arms a bit longer for the type of saw I have so I clamps it better

Had quite a few 4 x 8 ft sheets of OSB to cut up, and this made it much easier and a lot more accurate. My Evolution circular saw fitted perfectly. Nice and easy to set up and use.

Rectifico que si trae la mica y por eso le doy 5 estrellas

自作も含めいろんなガイドを試しましたが、その度に満足のいかない結果に残念な思いをしてきました。どんな道具にも使いこなすにはコツが必要で、しかしそれを習得する前に丸のこを使うのが億劫になっていました。ところがこのアキュカットは、そんな私でも一発でコンパネの長挽きに成功。丸のこを使うのが楽しくなりました。唯一越えるべきハードルは、説明書が英文だということ。でもそれはスマホに入力すれば和訳してくれます。そうやって地道に説明文と向きあうことで、より商品が理解できるというもの。おすすめです。

Super produit très utiles et rapide à monter expédition plus vite que prévue content en tout je le recommande