901 White Seam-Fil 1 Oz Tube

So easy to use. I had slashes--like from knives-- on my Formica. I put a small amount on a paper plate, stirred it with a toothpick until it got thick--just a few seconds. Then, I painted it with the toothpick--using a stroking motion. It dried within 10 minutes. I put a bit too much but used a clean sandpaper block n gently brushed it until smooth. Within a few hours, it was perfect! You couldn't even see where the original mark was. I used the same technique for other marks. I was very happy n very impressed!

There were two chips/gouges in the edge of the formica. That happened when I installed the dishwasher, it bit into the edge of the formica. Lots of people said that I had to remove that entire edge and glue a new piece. Nope.. Seam-fil is the answer. I had to use it in stages, filling up the depth of the gouge/chip. Took two days but the results? No one can really tell it's there. Ok if you got there 1 inch away and looking with your eyes you'd see where it was a slightly different seam.. But who does that?! It's fixed now and been that way for about a year.. Yes I waited to leave a review, it's the real deal.. I just warn you, make sure you have LOTS of ventilation around your work area! It is worse than nail polish remover.. . Had the windows open and a high velocity fan going! But the results are awesome!

My search for a white melamine hole filler found this product. The pros: + Free shipping when I bought a tube. + Pretty good customer product reviews. + Did a pretty good job filling 25 holes on our melamine board! + Comes in different colors & can be mixed to match most laminates. + Can be used to repair nicks, seams, gouges & will hide defects. + Drys, hardens very quickly. + Easy application with a putty knife. + Cleanup with acetone. The Cons: - $12.90 for a 1 oz tube is on the expensive side! - Flammable. - VERY strong smell, as this is acetone based! - This filler will shrink when used on deep holes. Our application required multiple applications, over several days! Closing remarks: ▪ Our water filtration upgrade project required reusing a melamine backer board, which the filters are mounted on. Using this filler was the lower cost option, to replacing the backer board. ▪ There were some deep screw holes on our backer board, so it took multiple applications of this filler over a few days. I applied this filler directly from the tube. The application wasn't too bad, just requiring a sharp putty knife. You want to use this stuff in a well ventilated room, as it smells real bad! ▪ Really no need to buy a special cleaner. This product is acetone based, so full strength acetone... aka, fingernail polish remover works perfectly to remove any residue. ▪ The attached pictures look splotchy, in reality they don't appear that way... perhaps the picture resolution Amazon allows? The finished result was pretty good... completely acceptable to me & I'm very picky. :)

The SeamFil product was easy to use and worked as advertised. For deep chips in Formica countertops, more than one application may be required as SeamFil does shrink a bit as it dries. For cracks and seams between separate pieces of Formica, SeamFil bridged the gaps nicely. Recommendation: watch the YouTube videos before using SeamFil as there are valuable tips on applying the product. My fault entirely: I bought the white SeamFil because it seemed closest to the color of my kitchen Formica countertop which is sort of a faint parchment/bluish color. The white SeamFil stands out glaringly. Perhaps I'll try spilling coffee on the repairs and see if the white can be toned down.

This worked great for repairing my countertop, can’t even see the cuts after applying.

I'm a furniture-maker who usually works in solid wood and ply, but for this project, white melamine was the best choice. I bought the seam-fil to fill and disguise the inevitable chips in the melamine from cutting on the table saw. The seam-fil recommends working it until it is thickening, but that didn't work well for me, so I started using it right out of the tube like the other reviewer. Using either method, the seam-fil doesn't really fill the chips. It turns them white and kind of plasticky looking so the chips are somewhat camouflaged, but there are still depressions in the surface. Also, you need to tape off the good melamine or it will change the sheen of those surfaces. It recommends a specific solvent, which of course I don't have, but I found acetone works pretty well for cleaning off residue (after scraping with a knife)...but do yourself a favor and tape off a clean line. I thought this might be a revelation that would allow me to invisibly seam 2 pieces of melamine together, but unfortunately, it is not. If I had time, I would probably just fill the chips with my regular wood putty and paint the whole thing with plastic paint.

This worked perfectly on a laminated counter top that had knife cuts due to slicing fruit. They are not visible now - great product

I've used this product for years on melamine surfaces on drafting tables. Application was smooth and made for a seamless surface even under the pencil and have had repairs last a decade...and still going