Spyder Signature GMC Sierra 1500/2500/3500 99-06 / GMC Sierra Denali 02-07 / GMC Yukon 00-06 / G

looks and works great, ended up soldering mine in, do not like quick connects, so the install took me a little longer. The only thing I did not like was where the up and down adjust was located, had to keep removing the headlight to adjust it, but it's not a big deal. once its set, its set. It is 100% better than the oem denali headlights I had bought, and had installed in my 05 Yukon. I hated the operation of the oem headlights, liked how they looked. I should have just installed these to begin with. Only question is, is that can the halo's and led's be hooked up to the DRL's instead of the parking lights? All the install instructions I found said to hook them up to the parking lights. Just makes more sense to me to have the halo's on when your headlights are not on. I don't usually drive around with just the parking lights on. Only change I made was to or some better lamps. the low beams it comes with are really yellowish. I ordered some Phillips diamond vision 5000k lamps for it, I did not want to go HID. hopefully they work out great. all in all, very happy with the purchase. looks great on my Yukon, and work great too. update: don't get the Phillips diamond vision 5000k lamps, they suck, look white when looking at them, but on the road at night, they cast a blue hue and you cant see as well. ended up using a razor blade and scraping off the blue coating.

I know i got an extremely good deal on these halo lights from amazon.com. They even came with instructions. Also u can go online to see how to put them in. Once you go halo it will be hard to go back to stock. Besides, most of the time, when u have a vehicle from 2002 like i have, they are gonna make something better when it comes to parts so i might as well have upgraded. They look really really good, but i like the look better when the rings are the only lights lit. These lights can run u 400 bucks, shop around be patient its worth it. For a while it took me a few minutes to understand what all the wires were operating, also i never used the new wire connectors before until today, and they made the installation that much easier. Total installation took about an hour but if including time it took me to figure out what the wires were for , it can take an hour and ten minutes. I own a gmc yukon xl 2002 model. When u get to wiring the LED's(white and black) and Halo ring(red and black) the Blue wire is the flasher(on the parking lightbulb), and the dark brown wire is the continuous power wire(middle wire on the bulb). The black wire on the bulb is the negative. I will post Pics. BTW so far im the only one in my area that ive seen with them, so yes yes yes yes. ok Im done

Build quality: These headlights look nice but the plastic is thinner than the original lights. The lense is thin but workable as these don't vibrate while driving on paved roads. Haven't driven offroad yet. The halos are dim and uneven. The bulb is on the lower side and the halo dims towards the top. I don't care for them and won't be connecting them. Installation: GM makes headlight installations very easy. However these lights are difficult to align with the rod holes. Adjustment: You must remove these headlights completely to adjust them. Doable but takes time and patience. The Up and Down marking is wrong. It is opposite from what is marked. The Left and Right is correct. Operation with Halogen Bulbs: These lights are pretty good. The hotspot is where it's supposed to be at the corner of the slant and there is good little dispersement to either side. These lights are adequate with halogen bulbs; however I'd recommend using some Philips CrystalVision. Operation with HIDs: With some 35W Kensun 5000k HIDs, everything becomes brighter. There is no change to the beam pattern or area of light concentration. I can't see any vibration however Verdict: These are nice but I will be running these with HIDs without the halos.

These took a little figuring but not bad. They fit absolutely perfect and look bad ass. There are 3 hot wires and 3 grounds. They come with one new bulb installed and you just clip that in the second takes the oem bulb. The wiring comes in when you take all the hot leads and connect them together. Then you run a tap from your day time running lamps. So not only do you have the drl. You also get the light up halos ( which look pretty sweet) and 3 led marker lights. I took my time and sodered the wires and used heat shrink tubing and zip ties to keep it all tidy. The black ground wires I crimped a loop connector and heat shrunk it. Then right behind the light ,pulled a bolt connected the loop ground and it grounded out perfectly. Each light took about a half hour to install Correctly . Combined with led turn signals and a billet grille it Gave my 2007 gmc sierra classic a awesome face lift.

The headlights look awesome and are very heavy and appear to be good quality. My problem with them is they didn't fit on the first try. They are larger than OEM lights around the edges and because of this I had to use my dremel to shave off edges so the mounting pin holes would line up. Otherwise the edge of the light pushed on the fender and pushed the light out of alignment. I also found the mounting pin bracket closer to the radiator was not seating properly and I had to shave that down as well to make the unit fit with the factory pins. I did this so that all my gaps would be even on the lights. The first time I mounted them the bottom of the light had a huge gap and protruded from the truck because the pins were not seating into the lower mounting holes due to the poor fitment at the edges and brackets. Be sure to take off the fan shroud while installing these because it makes seeing the brackets and where they are catching a lot easier so you know where to trim. I'm still working on wiring the halos and LEDs, if I find any problems there I'll update this review.

Updating my review: These are great! I have an old 2001 Yukon and with the stock headlights you really cannot see to drive it at night. I looked for something to improve that and ordered this product, after researching things. These work great. Even with the stock H1 bulbs that comes with the fixture. This really makes a 100% improvement. You can actually see to drive at night. Next, I may upgrade to LED bulbs, down the road. But again, even with the bulbs that came with it, it makes an incredible different on this old vehicle. Additional note: These really do just swap out. Pull out the 2 rods that hold the old fixture in, remove the old 9005 Hi-beam bulb from the old fixture and then insert these new ones in. These come with an H1 low beam bulb, but you will need a 9005 hi-beam bulb to put in it. Took less than 5 minutes to do both. There are numerous wires, but you do not have to use them, if you are just wanting high and low beam headlights, just swap out the fixtures and that's it. If you want the extra stuff like the halo lights, turn signal or parking lights, then you will have to wire those in.

Our 2001 Yukon Headlamps were faded and cracked. The Spyder Auto PRO-YD-CDE00-HL-C headlamps worked perfectly and provide superior lighting of the roadway. The installation was very straight forward. To connect the LEDs and the Halo lights you will need to determine the correct wires from the parking light/turn signal light lamps. In the 2001 Yukon, there are 3 wires, the blue wire controls the turn signal light (do not use this wire), the brown middle wire controls the parking lights (use this wire to connect the white and red wires from the LEDs and Halos) and the black wire is the ground wire (use this wire to connect to the black wires from the LEDs and Halos). Use a standard blue wire splice connector (http://www.amazon.com/Morris-Products-10774-Splice-Connector) to connect the wires together... I also wrapped them in black electrical tape. You will be reusing your existing high beam light bulb which works great too. Also, before you start make sure that you are installing the Left headlamp / Right headlamp on the correct side of the car... after wiring up the first headlamp, I discovered it was the wrong side of the car... darn. Also, when making the wire connections, be sure the wires are routed behind the grill and not on the outside. I hope this was helpful.

I thought I wrote a review to this and posted pictures earlier, but I guess I did not. I like the lights they work very very well. My issue with these lights is that the halos around the lights are not noticeably bright enough during the daylight hours. I would love to have them lit, bright enough as daytime running lights. During the night they look very good for during the day at a distance, they can barely be seen. My other issue is that the bright lights are not good! Usually regulates the beams are beautiful cover a lot of area and you can see further down the road which is very enjoyable for night driving. The bright lights are not good at all the regular beams work better than the bright lights does. When switching to the bright beams, the lights seem to go a bit further, but the Intensity in the beam direction is not a good quality. If you do not use your bright lights often and not concerned about the halo brightness then this is a good purchase. Don’t get me wrong. I do like the halos at night time you look very awesome and it even has the three LED blinkers on the side which you can connect to your blinkers, or you can connect them to your daytime running lights as I did along with the halos. you can be creative when connecting these lights to your vehicle

Great headlights, they look very nice. Easy to install. Ony thing, that could be done better is, the adjusters for the light could be in a way better spot where you can actually access them, instead of having to remove the light make your adjustments and reinstall. That gets very annoying very quickly. Other then that lights are nice looking and have made a big difference in about of light that comes from my truck now. I would recommend these lights, despite the adjustment issue.

La entrega se retrasó unos dias, pero llego en perfecto estado.

Good fitment. Will need to be aimed ,which is a bit of a pain. Will accept hid. And projects a good light pattern. Not blinding to other's. High beam pattern a bit off. But rarely use them having hid in low beam. Over all a good product.

Easy to install, look and work great with HID's, Easy to adjust and aim the beams where you would like, nice cut off line.. Haven't wired in the halo rings or LED's at the moment yet.

Perfect fitment on my GMC Yukon 2001. You gotta be ready to do some wiring and buy additional electrical components in order to plug the leds and halo. But overall very satisfied with the look and the clarity. With some led bulbs it is very bright and has a clean line.