SAPLIZE Bike Handlebar Grips, Ergonomic Design, PR02 (Black, Black Rings)

I installed these on my wife's and my bikes (3 total). I read that some had trouble with the screws stripping when installing. Therefore, I used vice-grips to squeeze the clamps (using a rag so as not to scratch the aluminum collars) 1st before I snugged the screws. These are comfortable and reasonably priced grips. I have a few hundred miles on my mountain bike using these grips and they stayed in place and feel good! Also, on one of my mountain bikes, I had limited bar end space so I cut 5/8" off the thin side to reduce these handlebar grips from 5" to 4 3/8". With a little ingenuity, you can cut the rubber and the hard plastic inner tube and still use the aluminum clamp.

I didn't use this for a mountain bike, I used it for a cheap, broken broom handle grip! It fit perfectly! IF you use it for the same purpose, carefully measure the diameter of the broom handle at the top after removing the bad grip... this happened to work perfectly, but it DOES have to fit slightly snug so it can slide up and down to install. BEFORE you add the GEL, figure out how you want the grip to be positioned for comfort because it's not symmetrical. i.e., turn left/right and pretend you're sweeping is all. I used some super glue GEL to secure it on the handle (slide it down a few inches from the top of the handle, apply a small amount of the GEL to the handle towards the top and slide it back UP so that the top tightening ring is FLUSH with the top - make sure the BOTTOM ring is the first thing to go onto the broom handle of course! Tighten the set screws, don't overtighten, no need to! Apply a small amount of GEL around the top edge of the handle opening/ring, gently tap the insert into the opening with a hammer (or even a flat-surface meat tenderizer!) and your'e done! Note: You could use the other grip further down on the handle to hold with your "lower" hand I suppose, I didn't bother. The main selling point of these grips overall is the apparent QUALITY of all the materials used including the packaging! If this all sounds to complicated to do, it really isn't -- better solution than throwing away the broom -- it's better than the "original" by far!

The only reason I didn't give these 5 stars is they seem a little hard to fully tighten down. They still twist. But I don't want to strip the screws so I'm being conservative when tightening and maybe I just need to really give them some torque. Overall very happy. Great price

Easy to install

I have an older mountain bike and the bar grips had deteriorated. I like the style of these much better as they allow me to rest my palms. They are comfortable, went on easy and look good.

They seem decent. Fairly comfortable. Rubber is a bit hard and I'm more into sticky rubber. Was going to keep them but can't get them to stay secure no matter how hard I tighten down on the screws. Will send these back and try another pair of better quality.

I bought these for an aluminum cane. The fit and comfort level are great.

These are probably just fine but cannot be installed on bikes with GripShift, twist-style shifters, or on bikes with bar end extensions. I rated 4 stars because I could only examine them - they could not be used on my bike.

Se ven de súper buena calidad y son muy bonitas. Sin embargo, no le quedó a la bicicleta specialized (para edades entre 8 y 12 años) de mi hijo que es rodada 24 porque el manubrio es más corto y estos puños son muy grandes que funcionan para bicicletas por ende grandes también, quizás de marco xs y/o rodada 26 en adelante que los manubrios son largos. Es una lástima, porque la verdad se ven muy buenos. Tuve que hacer devolución del producto y todo muy bien. Pero si los recomiendo!

Confortable et facile à installer!!

Buen producto, dan una buena sensación de agarre, son cómodos y evitan el estrés de la muñeca. No recomendados para down hill.

Los tornillos se barren muy fácil, los puños son muy comodos.

Yup, the smell is horrible and it won't come off. Stay away!