VideoSecu LCD LED Monitor TV Wall Mount for 19" 20" 22" 23" 24" 26" 27" 30" 31" Flat Panel Screen Maximum Loading 66lbs VESA 75/100 Ultra Thin Mount Bracket 1EA

Update: because of my setup I installed the mount side ways so the monitor slide in from the left to the right, because the mount has sorta a v shape going for it, took precise alignment to get it right but everything works and now I just slide my monitor to the left to remove it. Don’t mind dust in photo I’m doing construction In my case I didn’t have a stud to mount it too so I used a spare pice of wood affixed to the wall with toggle bolts and screwed the mount in. With the depth of the wood .75in the total space the monitor sticks out is 5in center and 9 inches on the extreme curve ends of the monitor (very small amount) Best flush mount on Amazon for a large 49inch monitor, very sturdy, best option for save space on a a narrow desk. Simple assembly didn’t even remove instructions from box. In my case my desk is 8ftlong by 19inches deep, with an 1800r curve msi oled 49 inch monitor, after trying other mounts this give me the most room and it’s far more sturdy. Honestly wouldn’t use a full motion for a 49 inch but if they could make one that overs small adjustments that would make installing even easier as if your not good at leveling you could fix it by twisting it level.

Very easy to install. Works great. Fine quality. simply screw the back piece to the wall (on a stud) and attach the other piece to the back of the TV and slide the two pieces together. It's not meant for large TV's, but worked perfectly for installing a 22" in my trailer. I did note that one of the screw holes was a millimeter or so off center from one of the holes on the TV, but it wasn't much trouble coaxing the mounting bolt into place. It comes with a few different sizes of mounting bolts to accommodate the differences in TVs. As has been said, it does mount the TV very close to the wall, so if the TV is also very thin, swapping cables might be tricky. My only warning is that if you are installing this in a confined space, such as close to a ceiling, or in in a cabinet, you will need to have at least 6 inches above where you want to your TV to be positioned in order to slide the TV plate into the wall plate.

Excellent mount to use a monitor as a family calendar. Hugs the monitor very closely to the wall. All you’ll need is a way to hid the cords and it’ll look like it was made to be there. Easy to install and comes with high quality parts. I highly recommend this mount. My monitor is a 32” LG

I purchased three of these to mount three LCD monitors side-by-side. They're very solidly constructed and the hold is very secure. All in all, the product does the job. However, the included documentation was not helpful. For example, the installation instructions called for using bolts that weren't actually included with the product (it came with screws in place of the bolts). Second, it only gave instructions for installation in a couple of different scenarios, neither of which applied to me. Therefore, the instructions were nearly worthless and I had to figure out how to install it on my own. In my case, I mounted the three LCD monitors to a 1"x8" board. To attach the rear mounting plate to the board, I decided to use the four 8mm holes in the "square" pattern on the rear mounting plate. I drilled four clearance holes in the 1"x8" board, one hole for each of the ones in the mounting plate. An 8mm drill bit is preferable for that task, but you could use a similar size fractional bit (e.g., 17/64th bit). Once the holes are drilled, you will want to use four M8 size bolts, four regular M8 size nuts, and four flat M8 washers. These will give you a very secure hold between the rear mounting plate and the board. Because they are properly sized to fit the hole pattern in the rear mounting plate, you will have little to no "play" in the position of the mounts -- this makes the fit nice and snug. Note that the drill bit, the bolts, washers, and nuts will need to be purchased separately from the mounts as this hardware isn't included with the mounts.

I've purchased several brands of TV wall mounts, but this one is superior in all aspects. It was used to mount a 24" Samsung in a guest bedroom. The device comes with all kinds of hardware for mounting the wall plate and the various screws of different diameters and lengths for the TV bracket as required by the TV brand. The outstanding feature is the no rocket science procedure to attach the TV to the wall bracket. Simply place the TV above the wall bracket and lower it into place after the two brackets are installed. The two brackets mate perfectly and it's done. No fancy hard-to-reach screws to tighten once on the wall and no complex self-locking mechanism to figure out. This is important if you need to change to another TV or reconfigure wiring in the future. Just lift the TV up and off the wall, make the changes and slide the TV back in place and you are good to go. The mounting assembly is quite thin, but allows plenty of room to run the COAX cable, power cord and HDMI cable (if required). My new TV is virtually flush to the wall and no bracket is visible. Buy it now and you will not be disappointed, rest assured. Thanks for listening.

I had very little space for a mount and found this one. I had 1-1/2" of space when the door was closed on this Box. The Display I'm using is just under 1/2" thick. This mount is just under 1/2" thick. I need a little bit of room to be able to hit the buttons on the back of the display. You can see the small buttons in the second picture on the top of the display there, which is the left side when looking at it from the front. So I added some spacers behind the mount on the back of the cabinet. it also gave me a bit more room to kind of slip in sideways and down. Because I'm limited on how high I can go inside that box. Another thing this mount has going for it is that it's VESA 75x75 or 100x100, on both the mount going onto the TV and the back bracket. The other 2 I also got, it was either for the TV, but the back mount was something else. Which if you're just mounting onto whatever, may be OK. But this Box was set up with holes for VESA 75x75 or 100x100 also. That was what won this mount over the others I had. With limited room, this mount couldn't have gotten much thinner!!! It also included all the screws and stuff you should need the normally mount your screen. It's well made. Comes with all the hardware you need. The one problem I ran into, I have the display bracket mounted. It's 75x75. I mounted the back bracket also 75x75, and the bolts I guess were hitting over the screws on the display bracket and so I couldn't get it to go down into the mount all the way as they were hitting each other. I ended up grinding the bold heads down to half the thickness they were for the back bracket. Mounted it back, and the Monitor slid into place. More than strong enough still to hold that little display up. If you can, use the 75x75 mount on the display side, use the 100x100 on the wall mount side. Then there's no chance of the screw heads on the one side hitting the bolt heads on the other side. or Visa-Versa. I also didn't use the screws to hold the 2 pieces together to lock the display on the mount. Because it's just too hard in that box to get to the bottom, and it's not going anywhere in that box anyway!!!

I am using 2 sets of these with Dell brand 27 inch Ultrasharp monitors. They would not work without modification. The back of the Dell monitors has a recessed VESA mounting surface. I placed the brackets on the back and screwed them in but since the mounting location is recessed, the 2 brackets would not line up and slide into each other. The mount that goes onto the monitor needs to be raised to be flush with the sides of the back of the monitor but it didn’t come with the proper washers to act as spacers. It came with some really thin washers but even using all of them it wasn’t enough to bring it flush with the back so I had to buy some plastic spacer type of washers to put under the brackets and now they work. Once installed and the security screws installed they are solid and stable, just be prepared to spend a little extra getting spacers if your monitors aren’t flat on the back.

The instructions were pretty straightforward. There are a variety of small screws to choose from to attach the plate to your monitor/tv etc, so you can find the ones that fit yours. I used a stud finder to attach the wall plate to the wall stud as recommended. The screws provided for the wall plate were too long so I used slightly shorter ones that I had - but it was just as secure. This is very solid, secure, and not coming off the wall until I take it off the wall. Well made, simple, perfect for attaching a small flat monitor to the wall above my desk. Very happy with product, arrived quickly and with everything described.

Sturdy and easy to install. Locate stud for added strength. Mount wall bracket, mount the other bracket to tv or monitor. Slides unit in place.

Great light duty mount. Very slim.

Excellent. Super strong.