Jamma Board Standard Cabinet Wiring Harness Loom for Jamma 60-in-1 PCB Board

Good quality Wire feels good and good fit on edge connector

I will not use any other brand of JAMMA harness after using this one. Three reasons: 1.) the wires are marked in English. Admittedly I have the JAMMA pin out memorized but it’s still nice to have English notation. 2.) the unused wires can be pulled out with a needle nose pliers. Usually on these harnesses the metal tabs are molded in but these are more like an insert (and thus are removable). Better than simply cutting used wires because you can put them back if you change your mind. I like neat installation and if (for example) I’m building a single joystick cabinet I’ll pull out the 2P joystick wires and all the other wires I am not using. Less of a rat’s nest when you’re done. 3.) I have had good experience with the seller Holland Computers. Great customer service, etc., so I want to keep giving them my business. In short I won’t use another brand. I’d even pay more, it’s just better.

Took no time to install in my cocktail cabinet. Color coded, clearly marked with numbers and where each wire goes to. Wires are plenty long and the connectors look to be pretty well soldered on. Great price as well.

I bought this harness as it's reasonably priced and used it to wire the WINNT 60-in-1 JAMMA board . All minimally required features for a 2 player arcade are available with this harness. The quality of the wiring is good and does not feel cheap. Inexpensive? Yes. Cheap No. However, take care to make a note of the following and these do not make the product necessarily bad or poorly rated! It simply may not be suitable for your arcade application. 1. This is not a full harness and there are no wires supplied for features that are not supported. Example, the extra #5 and #6 fire buttons. 2. The harness does not do a good job of fool proofing against incorrectly plugging it into the board. You have to make sure that the group of thick Red and Yellow power wires are oriented up and to the top-left corner of the board when holding the board right side up with the VGA Monitor port pointing in your direction. 3. There are no English descriptions on the harness. Covering the plastic plug with masking tape and marking the terminals by looking at the wiring in the JAMMA board manual makes for trouble free wiring. 4. The crimped terminals on the harness are the smaller 3/16 inch female blade connectors. If you want to wire a 4" speaker, you may have to replace the 3/16 connector with the wider connectors that are 3/4 inch type as most speakers come with 3/4 male blade connectors. 5. Finally, the 1- Player and 2-Player button wires maybe identical in color (in my case, Brown) . Therefore make sure you identify which wire goes where so you don't cross wire these 2 buttons. The same goes for both (+) and (-) speaker wires (mine were White). Overall a simple, usable harness that works with a super simple arcade set up!

how these is so cheap is beyond me. it saved countless hours of soldering/wiring if you have a 60-1 or ANY jamma board this is the way to go/ if you cut wires just take your time and doublecheck everything lol had my 1up conversion up and running within an hour ZERO COMPlAINTS

Works as should, have not set up the cabinet but was able to test and works great

This is a DANGEROUS product! It uses EXTREMELY thin gauge wire and hides this by using very THICK insulation. Just see the picture of the wire cross section. Arcade games can easily use upwards of 15A and this will cause the wires to melt and could cause a fire by shorting out your power supply or burning anything flammable nearby as the wires and insulation melt. It is NOT SAFE to use this wire harness for powering any electronics. I would not use this for any purpose. It represents a clear hazard to the user. Buyer beware!

Bought the harness for a custom arcade build so I cut off the plug but the harness is great!

I used it to made an arcade from scratch and all work as well :).