JETech Screen Protector for iPad (10.2-Inch, 2021/2020/2019 Model, 9/8/7 Generation), Tempered Glass Film, 1-Pack

This is the second JETech glass screen protector I have bought and installed. The first was for my work iPad mini, and this one is for my larger, personal iPad Pro. This is a buttery smooth, high gloss glass protector that goes on very nicely! The sticker hinge system works quite well as long as you are careful. The process is in the instructions, but goes like this: Stick the stickers on the back half on and off the iPad. Position the screen, then fold the hinge stickers over onto the screen. Stick another sticker on the opposite side to lift the screen off and out of the way, folding like a book cover with the hinge stickers. Clean the screen with the provided wet wipe, the dry cloth and then use a sticker to remove dust. Remove the film from the side that will contact the glass. Fold back over and lay it on the screen. Press from one side to the other to get out the bubbles / air. Done! A piece of advice. Spend some time dabbing the screen with the sticker to remove the dust. Spend more time than you think is necessary. The cloth leaves a few bits behind and the environment will deposit some dust. Do it in as clean a place as possible because you want the screen to lay down with no dust. If you see a piece (I had one) lift a corner gently and use the sticker to grab it by sliding the sticker underneath to get it. The results are spectacular. Beautiful screen that protects and allows the iPad screen to shine through. Works great with the Apple Pencil. Flawlessly. (If you don’t mind a slippery drawing surface. It’s not like paper. I don’t mind this. If you want a paper like feel, grab a matte finish protector. Not this one). I love my Otterbox. It has saved me countless times from damage. But, I despised the plastic screen protector that comes with it. Solution? Remove the plastic by hitting it with a blow dryer around the adhesive (inside the cover) and gently lift the screen out. At the right temperature most of the adhesive will lift off with the plastic. A little Goo Gone and a paper towel will take care of the rest. Put it together and it fits perfectly. Now, my pristine glass will remain so, and I don’t have to worry about dust under the screen cover ever again. Take your time installing, dab ALL the dust away before the final flip, and you won’t be disappointed. Great price too. Thanks JETech!!

The product was a perfect fit on my 12.9 I Pad Pro. Easy install and everything was included for the installation.

Great instructions and went on easily. My screen is cracked on the edge and near the button so I could not get a perfect seal but it's my damaged machine that was the problem - iPad 4 Ps an iPad four with the old iOS is not good to browse the Internet, the tech is just too old :)

Excellent quality. Fit my iPad mini model # perfectly. Provided everything needed for proper installation. Would definitely recommend.

Update: after a week, I found my iPad on my couch face up with the screen protector shattered. It looked like it took an impact from the very left edge. Not sure what happened exactly (I was home alone working and nowhere near it) so I can't blame the protector for randomly failing nor can I give it credit for saving my screen either. There was no damage to the screen. After using the iPad without a protector for a few days, I noticed that I preferred having this one on because while it's glossy, it's still much less fingerprint prone than the screen itself and it has a smoother feeling as well. I still had the same installation issues where the various application stickers wouldn't stay, reported it through the Amazon app and got a replacement (so 3rd one now). I used scotch tape for hinges and also to lift the screen instead of the supplied stickers and had much better success with this 3rd and final application. So, in my opinion the only stickers you should use are the ones to pick up the dust. Those work great. However, if you replace all the other application stickers with scotch tape, I think you'll find you'll have much better success. I'm finally happy with the product so I'll give a few stars back. Original review: The protector itself is great. Can't really tell it's even there. My gripe is with the application process. You are supposed to strap it down on one side with two strips of adhesive so that the protector can be lifted from the screen, the screen can be cleaned, then you can peel off the plastic from the back of the screen protector and finally apply it to the screen. This sounds like a great method to apply it straight if only it would actually work like it's supposed to. There is another strip of adhesive that you are supposed to stick to the outer part of the screen protector so you can use it to pick the protector up off the screen to clean it as I mentioned earlier. This strip of adhesive was not sticky enough to lift the screen protector up or lay it back down so I had to use my bare hands instead. Luckily I managed to salvage the install but I felt really lucky. Might not be so lucky next time and it could've been a disaster. I like the protector so I may buy this brand again in the future but I'll probably replace that strip of non-sticky adhesive with some scotch tape which I'd hope would be much more sticky and work better. Other than that, it's great.

Slightly smaller than the screen but worked great. YouTube video for install super easy.

Worked perfectly. This appears, so far, to be very sturdy and a quality product at a reasonable price. I recently installed a tempered glass protector on my iPhone 5s and loved it. When my one year old film type screen protector became loose at two corners and began lifting, dust and bubbles were getting underneath so I decided to try this glass protector on my IPad Air. I removed my old screen protector, using the "good" side that was still very sticky to lift off any dust. Then I cleaned the screen with my own alcohol swab (not included but think that it should be). I highly recommend this step if you have any swabs handy. I did remove my IPad from its case and then used the little dust catcher sticky thing that came with the protector and went over the screen again. The dust lifter provided was the size of an iPhone though. I think a full size dust lifter would be better but it worked fine, so no points off for that. Then I gave the IPad screen a number of final swipes with the provided cloth. I removed the protector from its envelope and attached the two little red tape guide things on either side of the middle of the top side of screen protector. These are handy to position the protector over the IPad screen as you maneuver it into the righ spot. Next I peeled off the backing marked "1" and began my installation. It took me less than 30 seconds to position the piece over the two circle cutouts on top and bottom of the Ipad screen to my satisfaction. I wanted to make sure that it would land perfectly centered over each one. Then, I carefully lowered the protector and, voila, the thing just installed itself without a single bubble. There was no top film to remove which wasn't needed anyway as there was no need to use a squeegee or credit card to install and/or remove bubbles. I ran the cloth over the whole thing for good measure. It looks beautiful and everything performs as if it wasn't even there. Easiest iPad screen protector I ever installed. I would highly recommend this product so far. If it protects and stays in place as well as my iPhone glass protector does, then this will continue to be 5 stars for me.

It fit as it should and was easy to place. It came with a card that made smoothing it down a breeze.

I don't normally bother writing reviews for my purchases but I'm so impressed by this screen protector that I thought I would this time. I've bought and applied many different screen protectors of different kinds for various devices over the years and found that this one has gone on the best. Absolutely no bubbles!! I was very nervous because of the size of the screen (12.9 inches) that I would have difficulty but it went on perfectly at the first try. It comes in a very sturdy box with a cloth for cleaning, a blue sticky sheet for removing dust (which was perhaps a bit smaller than I would have liked but I can't complain about the results) and a couple of sticky tabs to help you align it. The protector itself is an absolutely perfect fit from edge to edge (barely a quarter of a millimetre smaller than the original screen) and around the home button and with about 0.5 to 1mm clearance round the front camera. For this reason it is important to get it lined up right and to do this I ignored the instructions (which say to put the tabs in opposite corners and lower the whole thing down onto the screen in one go). Instead, after cleaning the screen, I lined up the protector, with the protective backing film still on, and stuck tape onto the front of the protector that wrapped round the long side of the iPad and round to the back of the iPad to make a kind of hinge at the top and bottom of the long edge (making sure the tape was pulled quite tight). I used the two sticky tabs supplied to stick on the opposite edge to use as handles. I lifted the protector out of the way and used the blue sticker to remove any dust on the iPad screen. Holding the protector by the tab handles I peeled off the protective backing (trying to keep the underside facing downwards as much as possible to avoid dust falling onto it) and used the tab handles to lower the protector into place while pulling to keep the sticky tape hinges tight to keep everything aligned. The result was perfect! Before I applied the protector the iPad screen tended to be a complete fingerprint magnet and a constant smeary mess. But the protector is absolutely brilliant. I've been using it for a few days now and haven't cleaned it once but I can hardly see any fingerprints. The clarity and sensitivity seem great too. I would thoroughly recommend this product.

Just I need to tell you it’s on of the simplest products I’ve ever used in terms of installation. Finally got a well-designed screen protector without finger prints marks and easy clean.

Ürün elime 3 günde geçti bukadar çabuk geçeceğini tahmin edemedim sevindim. Ayrıca fiyat performans ürünü. İlk denememde sorunsuz taktım. Hava kabarcığı bırakmıyor. Kesinlikle tavsiye ederim. Firma çok ilgiliydi. Parmak izi de bırakmıyor. Paperlke tercih edecektim ama görüntü kalitesini bozduğu için etmedim. İyiki bunu seçmişim.

Questa pellicola JETech è esattamente ciò che cercavo per il mio iPad Pro 12.9" di seconda generazione. Facile da applicare, ben confezionata e con una qualità che si nota subito. 🛡️ Vetro temperato 9H Resiste ai graffi, anche quelli più aggressivi. Ho provato con le chiavi in tasca: nessun segno. Lo spessore di 0,33 mm è perfetto per proteggere senza compromettere il touch. 📱 Alta trasparenza e sensibilità Lo schermo resta luminoso e reattivo. Nessuna interferenza con Apple Pencil o con il touch. Sembra quasi di non avere nulla sopra. 🧼 Installazione senza stress Niente bolle, niente polvere. Basta seguire le istruzioni e usare il kit incluso (panno, adesivi, guida). In 5 minuti è perfettamente applicata. ⚠️ Compatibilità da verificare Attenzione: non è compatibile con i modelli 2018 e successivi. Solo per iPad Pro 12.9" 1ª e 2ª generazione (modelli A1584, A1652, A1670, A1671, A1821). 💡 Conclusione Un prodotto semplice ma efficace. Se hai un iPad Pro 12.9" del 2015 o 2017, questa pellicola è una scelta sicura e conveniente.

çok hızlı geldi, ürün de çok kaliteli. tavsiye ederim.