HumanCentric VESA Mount Adapter Compatible with Asus Monitors MX239H, MX259H, MX279H, MX299Q, MX25AQ, and MX27AQ, Does not fit VX Series

$15 is a fair and reasonable price. I believe this is about half the price of the prior iteration. Bottom line... does what it should. Other notes: The monitor does sit higher than other monitors, which have a built-in VESA mount, due to the fact this mount isn't very tall and the VESA mounting holes wind up near the bottom half of the monitor. But that's probably a mechanical trade-off, as any taller mount would increase the moment arm and make it almost impossible for a monitor arm's tilt not to tilt downward, due to gravity. As it is, I had to tighten the tilt more than normal due to the design of the ASUS monitor's support arm. There's a little give on the mount, when mounted and in use. Makes fine tuning a bit tough. But once it's set, it's stable. The contact area, where the back of the monitor's mount contacts the mounting slot on the adapter is not fully flushed. The back of the monitor's mount is slightly curved, while the adapter slot is straight. This is the primary cause of the slight instability, when trying to fine adjust the mount. The contact point between the monitor mount and the adapter is too small. These are nit-picks. This is a fine solution to an ASUS design flaw (i.e. not including VESA mounting holes). Thank you, HumanCentric!

The bracket works on a MX27A (similar to the MX27AQ listed above). The sheet metal is a little thin for the cantilevered monitor weight so they wiggle when the supporting table is bumped. As mentioned in other reviews, the included screw that mounts the monitor base to the bracket is too short. Use an M6x15 if only using a flat washer or an M6x20 if using a flat washer + split lock washer as I did.

Works great. The monitor has a slight, intentional give that makes it easy to adjust, yet it feels completely secure and stable once positioned.

Not too much to say. It fit like a glove and doesn't feel flimsy. Goes on with no issue and was decently priced

It does the job and works sufficiently. However, the screw that came to attach the mount to the monitor did not fit. The good news is the screw on the existing mount worked. While this does work for my setup, it does not mount or hold it as securely as other mounts. This is made for specific monitors, but it feels a little "wobbly" and while it holds it firmly in place, as you move the monitor, it takes some time to get it properly in place compared to other mounts. That is just one of the trade-offs when you have a monitor without a VESA mount. So yes, this does the job, but all my future monitors will have a built-in VESA mount.

It works as it says it does, but it could use a little more to make is a tad bit sturdier for my use. I swing the monitor around a lot and always feels flimsy.

Works as it should, just a bit expensive in my opinion.

Use the bottom screw from the display and not the one that comes with this mount. The latter is shorter and bit scary to trust the display weight. Everything else is great. The product feels so well built that it almost feels like an official product.

hatte von diesem Artikel 2 passt alles super musste nur ein zurück senden da der andere bilschirm von montur her ähnlich war aber leider schraube zu kurz. kann ich trotzdem empfehlen mit prime in der Regel am nächsten tag da.

Acquistato per attaccare un monitor Asus con una "gamba" verso il basso a un supporto a braccio. L'adattatore è un grosso pezzo di metallo (e in quanto tale direi abbastanza sovrapprezzato), e ahimè fa quel che può. Alla fine, sono soddisfatto del lavoro, ma il sistema che ho installato è un po' instabile. Se possibile, anziché appendere il monitor, considerate una base che ruoti su cui appoggiare il supporto originale.

ASUSのMX239Hをモニターアームに付けるために購入したけど今のところ問題なし。 少なくとも可動しない固定タイプのアームなら重さで下向くとかは起きないのではないかと。 金具分だけ少し前に出ること以外に欠点は無く、それもアームなら少し後ろにすれば解決したので。 今時VESAマウントの無いモニターは少ないと思うけど、そういう不幸？なモニターだった場合の解決法としてこの手の金具は選択肢としてアリかと。日本語のレビューが無かったので参考になれば幸いかな。

It's a bit large and you can see it under the monitor at certain angles but it's not too big of a deal breaker. Very easy to install and seems robust, doesn't give you too much freedom for thicker cables through the slots tho. To install just unscrew the bottom of the stand and remove the ring, screw the bracket on by reusing the screw.

O produto tem óptima qualidade mas, para quem precisa de um adaptador para fixar um mini PC a este monitor ASUS MX239 mantendo o suporte de secretária original, este não é o produto que procura. Este produto só serve para adaptar o monitor para um suporte de monitores articulado VESA.