Niviy Static Cling Non-Adhesive Window Film Frosted Glass Bathroom Door Decoration Privacy Covering (17.7"x 78.7")

I love this privacy film. So easy to install, and I love that it still lets in some light. I put this on the transom above our deck door to stop the bluebirds from pecking at our window. They would see their reflection and think they had to protect their territory. From day one of putting this up, no more pecking or bird poop on the sill.

Provided the privacy we were looking for. Easy to install and cute to look at.

Très facile à poser et très joli.

Very nice design, easy to apply, and adheres well to the window. I love the way the light filters through the film and reduces glare and heat. I'm not sure how durable it is but it's a good value for the money and provides privacy.

Ok, this is an honest review based on hours of research in choosing the right film to give privacy in our bathroom without blocking too much light. The ones that look like stained glass are very pretty if that's the look you want? However they are not actually colored it's a prismatic effect from the sunlight shining on it. I'm not looking for that I want privacy not glistening rainbows. Then there's the pattern ones with birds and the like. Some of these offer privacy and some don't, choose carefully. As this is my bathroom/guest also, I'm not looking to make the window a focal point of design. So I ordered privacy film with a slight floral pattern (trying to please wife also). That being said my careful research paid off. It met my expectations. Now for the second part of my review the installation. Lots of things to address here. First I will address the naysayers who's film didn't stick. Your wrong you installed it incorrectly. How do I know, well I'm a semi retired professional wallcovering installer and own my own wallpaper installation company. I'm a licensed contractor with over 40 years experience of hanging wallpaper every day and trust me when I say the process is similar. First of all examine your product keep it in a warm room for at least a day not your unheated garage in winter. Examine the product and determine which direction you wish to install, vertical (easier) or horizontally. Cut the film about half to 1 inch bigger on all sides. Don't cut to fit beforehand. The product has a film on the back that MUST BE REMOVED or it will fall off and you will be using scotch tape and complaining here. The smooth side not the textured side is the side that will stick to your glass which will be on the inside of your home, not to be installed on the exterior side of glass. So now you have your pieces cut correctly and are ready. But first you must thoroughly clean your glass and remove all contaminants especially flecks of paint, dust, dirt etc even invisible microscopic grain of dust will cause bubbles, similar to that protective film you badly applied to your phone so paid the guy at the mall $20 to do correctly. I recommend using isopropyl alcohol or other cleaners such as paint thinner or even acetone (nail polish). After that use vinegar and water or at least Windex. Get a nice pump fine mist spray bottle add water and a drop of detergent shake and spray the glass thoroughly and evenly. Keep a towel handy to wipe up drips and all the goo from the window sills you never clean. Apply film and slide into position butting one long side to the edge of glass or trim.gently use a squeegee preferably one with a no scratch felt side to push bubbles to edge and out. You can buy these on Amazon or big box stores or use a flexible wallpaper plastic or heck even a credit card will work. Once you've got 90% of the bubbles out except at edges use your plastic FIRMLY TO crease the edges. Take your snap of blade knife and run the knife and plastic along the edge, lift up the corner you can't cut and cut with the knife or scissors (better) that last 1 inch. Rinse and repeat. You will have a few small bubbles. Check your cuts where the bubbles are and it's probably trimmed too fat and putting pressure on the film which causes it to bubble, re-trim using the knife on the inside of the plastic this time. You may get 1 or 2 small bubbles. Don't worry wait a couple of days and it will shrink and suck in to the glass adhering tightly. You can also make a tiny, tiny cut into a bubble with your blade and smooth down if you like, but please don't poke with a pin or you will have a permanent visible hole. After several days you will think that a professional like myself installed it for you and you can pat yourself on the back as you have saved yourself hundreds of dollars on installation and can volunteer to do all your friends and neighbours windows. Your welcome, good luck !!! I'm Gary and I install "Ultimate Wallcovering" in Southern California, and I approve of and recommend this product. Remember....measure 3 times cut once !!!