Corefix Connect 6x Heavy Duty TV Wall Fixings For Dot & Dab Plasterboard

I used these TV Wall Fixings to mount a 32” flat screen TV on a wall that I had installed insulated plasterboard on, and I couldn’t be happier with the result. They provided an incredibly strong and secure anchor point, with absolutely no movement, sagging, or any signs of strain — even after the TV was fully mounted. Installation was straightforward thanks to the supplied drill bit, and the quality of the fixings gives real confidence that the load is properly supported. If you’re planning to fix anything heavy to insulated plasterboard, these are an absolute must. Solid performance, great value, and total peace of mind — exactly what you want when trusting a product to hold your TV! Highly recommended.

These fixings are seriously impressive. I’ve used them on soft thermal blocks commonly found in UK housing, and they still hold incredibly securely, which gives a lot of confidence when mounting heavier items like TVs or shelving. Installation is straightforward with the included drill bit, and once fitted they feel completely solid. The design really helps bridge the gap between plasterboard and the softer blockwork behind it, which makes a big difference compared to standard fixings that can feel unreliable in these walls. Even in less dense materials like thermal blocks, they don’t loosen or shift, and everything feels locked in place properly. It’s one of those fittings where once it’s up, you don’t think about it again. Easily a 5-star product — especially impressive in modern UK housing materials where many other fixings struggle.

Perfect fixings, It is a challenge drilling through the soft plasterboard then trying to align the drill as best as possible when going through the cinder block behind due to its uneven construction (the drill will want to wander) but these plugs worked perfectly highly recommend for dot and dab walls, nice and strong, would recommend buying more than you need if using for the first time though just in case.

A godsend but.......not as easy to install as they make out Firstly, you should drill a hole depth a bit deeper than they recommend. This is because rubble/debris falls and collects at the back of the hole thereby shortening the hole's length, and this results in the plug and/or the screw bottoming out (not being driven in all the way). The instructions, in the form of 'pictorials', do recommend blowing air into the holes to clear debris before inserting plug and screw, but doing so isn't always possible. The next issue is that sometimes the hole is tight which means you have to bang quite hard on the plug to knock it into the hole. This can result in the head of the plug collapsing/crumbling before you have driven it in all the way. Also, hard banging can lead to damage to the plasterboard. Next up, is the issue of the plug head. This has a large flange/shoulder which has to be knocked quite hard for it to sink into the wall so as to be flush with the wall surface. So that's yet more banging; not good. Of the six fixings I put up only one of them went in 100% smoothly just like the adverts and review demos. My advice for a totally hassle free application is to do as follows: ~ buy a compressed air canister before you start ~ to be on the safe side, drill hole depth a lot deeper than recommended (for 95mm fixings, drill hole depth to around 110mm) ~ make the back end of the hole a tiny bit wider (you can do this by using a drill bit one or two sizes smaller in diameter and then wiggle it around at the back of the hole) ~ use a countersunk bit or drill bit the same diameter as the plug's flange to create a recess just deep enough to accept the flange without you having to hammer home the plug too much in order to make it lay flush with the wall surface. Once those preparations are made this kit will be effortless to install. Once installed these fixings are incredibly strong. I didn't bother to test the claim that one of the two brackets I put up to support my oven, can take 70kg. However, it's clearly a neat and effective solution to the problem of securing heavy items to a 'dot and dab' wall.

Perfect fixing everytime. I’ve used these throughout my entire home. I’ve had every radiator replaced and used these for the brackets and for tv brackets also. Perfect for new build homes with dot & dab walls onto breeze block.

Excellent product floating shelves went up no problem solid one happy wife

After trying to use the wall fixings supplied with the TV bracket I ordered it became apparent that they would not work with my dot and dab installed plasterboard wall (on to blocks). After a fair bit of research I found this product and it worked a treat. The screw heads were wide enough for them to work with the washers for the wall bracket and there is absolutely no movement from the 30kg TV. The screws sit in the plastic raw plug and a metal tubular sleeve which is so simple to install and gives a very secure fix. They say 4 screws will support over 100kg and that seems a very reasonable claim. The fact that you get a drill bit included makes this purchase great value for money. Was so happy with the purchase and for any other heavy objects, this product will be my first port of call!

Whoever thought of these fixings should be awarded a medal, my last two houses have dot and dab walls, in my opinion these are the only fixings to really work, I’m only a diy guy but five stars all round.

Macht was es soll

Pas encore installé mais je pense que c’est un bon achat

Super Quality ... used to anchor through insulated plasterboard onto block.

Great for drywall with block behind

This fixing works perfectly for dab and dot walls. But a bit expensive.