W10542314 Dishwasher Door Seal Gasket Strike（Improved version）by Romalon Fit for Whirl-pool AP5650274 PS5136129 W10284090 8268888 black

Fit perfectly and stopped my door leaks completely. Easy to install also.

This gasket was easy to install, inexpensive, ($11), no service call needed. Plus Whirlpool has a YouTube video - short with minimal extra "talk." There are other videos. I do recommend starting the installation of the gasket under the locking mechanism attached to your counter. This way you can divide the gasket into 2 equal parts. Take your time installing the gasket into the 2 curved sections of the dishwasher frame. Make sure both sides are flat - not "pulled" toward the interior of the dishwasher. Slowly press down on the gasket as you are installing it into the channel. Once installed, return to the top middle of the dishwasher and press again the gasket - slowly, inch by inch. I tested the dishwasher by placing two small pie pans with paper towel squares at the bottom of the dishwasher right and left sides. I had a drop every minute or so, I then pressed the gasket again using the flat part of a dinner knife handle. NO LEAKS!! Be patient. Good Luck

Fit and worked well

After trying to find a technician come in and take a look at leaking dishwasher for 5 or 6 days I finally decided to take matters in my own hands. Less than 24 hours and $11 later (Amazon Prime) got this door seal, removed the old one, and installed it in about 20 minutes, tops. Ran a few cycles and confirmed that everything works fine now and no leaks. No tools are needed, you just push it into the opening with your fingers and it stays there. It's a bit too long so I had to cut 2 or 3 inches, I think it's by design. 10/10.

Fit perfectly and did it in myself in 15min. The latch piece was useless but didn't need it anyway.

I purchased this gasket after searching for the Whirlpool part number from my dishwasher service manual. The gasket and door strike arrived in good condition. My dishwasher (Whirlpool Quiet Partner IV, model GU2475XTVY0) had a metal strike already, so I did not use it. The dishwasher door did not close properly after installing the new gasket. I suspected I made an error during installation, so I watched many YouTube videos since there were no installation instructions included. I then reinstalled the gasket using all the tips collected from videos: heating the gasket with a hair dryer to make it more pliable, using the rounded handle of a dinner knife to press the gasket into the gap. I triple-checked the orientation. I was careful not to stretch the gasket during installation. No luck. Next, I pulled the dishwasher out from beneath the countertop and used woodworking clamps to hold the door shut against the dishwasher tub. I ran the hottest cycle I could. When the wash cycle was complete, I carefully removed the clamps and the door popped open. Thinking that the gasket would eventually "settle," I clamped the door shut again while my family was out of town for over a week. When we returned, I ran a rinse only cycle as a test without the clamps holding the door shut. The gasket pushed the door open, halting the cycle. (You can tell this happens when the start button LED starts blinking.) I ended up taking the original, worn gasket out of the trash, cleaning it, and reinstalling it in the dishwasher. The door now closes properly again. I can't return the gasket because I had to trim it to length to fit inside the dishwasher. Fortunately, it wasn't very expensive. Bottom line: if your Whirlpool dishwasher uses gasket part number W10542314, this third-party gasket may not fit correctly, and you won't find out until it's too late to return the product. I regret purchasing this item. --- 2025-11-19: Thinking that my door latch assembly might be at fault, I ordered a replacement door latch (OEM part) and installed it this evening, then reinstalled this gasket. My theory was that the door latch had become worn over time and didn't have the holding strength necessary to keep the door closed with this new gasket. Unfortunately, the new door latch did not make a difference–the door still pops open with this gasket installed.

This does NOT fit my whirlpool dishwasher quiet partner ii even though it says it does. It is bigger. Watch out! updated to say, get a heat gun and warm it up. also measure using the old one. Make sure curved aread faces inside tub. It's still hard to force in but I did get the door to close finally. We will see how it works

This seal was about a foot longer than my Kenmore needed. Installation was simple. After removing the old seal and carefully cleaning the grunge and soap scum that had accumulated around the perimeter of the door, I moistened the length of the new seal with water and a little dishwashing liquid. My only concern was that I had not paid attention to the position of the little flap that forms the seal. Should it point outward towards the edge of the door or inward toward the interior of the dishwasher? There were no instructions provided. Perhaps it would have made no difference, but I opted to have the flap point towards the interior. It seemed there was less risk of it getting pinched that way. In any case, it did not leak. And I was pleasantly surprised that the effort required to close the door increased only slightly.