Diablo Steel Demon Cermet II Saw Blade - 6-1/2" Diameter, 48 TCG Teeth

I do not often review products, however this saw blade has changed the way I work with steel. I thoroughly enjoy fabrication and welding. Prior to this saw blade I made most of my cuts with a torch or cutoff wheel. This has made it so much faster and easier to cut straight lines on full sheets of steel, especially when paired with a cordless circular saw. I have not worn one out yet and will add to my review when I do. Attached are a few pictures of a some 1/8” flat stock I cut to show the side profile. Crisp clean edges, no sharp burs. Excited to see what else this product can do.

I can not believe how well this thing works. I use metal roofing materials often, and have cut them with several different methods. I saw these in a local store, but it wasn't in the size I need for my cordless saw. At nearly forty bucks, it wasn't gonna be an impulse buy anyway. Since I decided to go for it, though, I am crazy about it. My 18 volt saw struggled to cut metal with my previous blades, and it really went through the batteries fast. I haven't used this blade on an extended project yet, but the ease with which it cuts tells me that those problems are over. I haven't had it long enough to attest to its durability either, but I expect that it will be around for a while. This just based on the lack of stress that the blade and saw experience during use. It just seems to sprint through a cut and be looking for more. At long last I have the right tool for the job!

I bought this blade for my Milwaukee cordless metal saw. I used it to cut some 1/8” angle and flat steel. It worked great. I knew my old blade was dull but I didn’t realize just how bad it was. This new blade cut the steel very easily. I did notice there are already a few chipped teeth but that is more likely because of me than the blade. A good metal blade for the money.

Cermet blades are awesome for cutting steel. Turned my small wood only saw into a metal cutting beast. Just go slow. Great value. Long lasting.

This little fella survived about 30 mitre cuts through 16 gauge 2" square tube, mild steel. I would say this is a bit outside its intended stock, so I can't really be critical, but at over $1 a cut... I put it in my circular hand saw and the first few cuts went like butter. The cuts were so smooth and clean, they were a breeze to weld up. Once this blade died, I used an abrasive wheel in an angle grinder and of course the gaps widened. I probably am going to spend in argon and welding rod what I would've on a new blade. Six of one, half-dozen of another. I think if you had a smaller mitre saw this blade would work really well. I have a 10" chop saw and this blade just would not have reached the table. I think it would be a great blade on thinner material though. Wish I'd had one when I was doing my metal roof, although those slivers....

After watching several video demos of this blade cutting steel I can say without hesitation after using it, this blade is amazing. I cut tabs off of a stainless steel shower corner shelf like it was butter. The blade did not heat up or mark or otherwise distort the shelf. I also made an exacting trim on the same corner shelf piece effortlessly. I didn’t think it even possible to cut 1/4” thick metal with a cordless 6-1/2” circular saw but it with this blade

These blades are amazing. One of the best I’ve worked with. I don’t feel like it lasted too long but I really did beat these up. Will definitely use these again. I also have an aluminum blade that worked great as well. In a smaller power circular saw, it can bind a little…but slow and steady, great great saw.

Had to cut 3/16 steel and was not sure this would work. Not a problem, just like butter. The steel was not hot when cut. Used a 6.5 inch blade on my 18V Makita saw.

Me sorprendió corta muy fácil el metal ya lo use para cortar tubos eléctrico, ptr de 1 1/2 incluso placa de 1/4 de grosor y corta muy bien lo que si recomiendo es usar una careta para cortar ya que si desprende rebabas al cortar y con los lentes no es suficiente protección

El paquete fue recibido un día antes de la fecha de entrega, super recomendable el discole daría más estrellas pero solo puedo 5, compañeros no se arrepentirán si hacen la compra vale la pena invertir Seguiré comprando este producto definitivamente

El filo de los dientes muy bueno