Aquor RV City Water Inlet, Quick Connect RV Water Inlet Replacement for Motorhome, Camper, and Trailer, Stainless Steel Flush-Mount, Black Cover, ½” NPT (f) x ¾” GHT (m)

When I was redoing the plumbing I replaced the city water inlet at the stern of the boat with this one to have a quick connection and eliminate having to fight with the hose and the 3/4 inch inlet. The quality is excellent and is a close match to the other stainless steel fittings I am using for the washdown, water tank fill, waste pump-out, and fuel inlet (the boat is dirty from working on it and the water inlet isn't changed yet). I chose this product because the cover provides a good seal to prevent contamination from entering the water supply. The previous inlet I tried was not as durable and the cover would not stay in place, and had the 3/4 inch inlet. For a matching washdown outlet I used the Aquor Marine Deckwash. RV city water inlet. That piece is almost identical, but is embossed with "washdown" instead of "aquor". The check valve held properly against the 55psi pump on the boat and the high-pressure city water. You will want to add a 3/4 inch female to female adapter as this only has a 3/4 inch male connector and you will probably find a male hose end at the marina. This is a great value for the clean look and ease of use, and I expect it to hold up for a long time!

Excellent. Just installed this item on my trailer. I got tired of the leaky faucet, and tired of using two pliers to tighten the connection. Although this was a bit on the expensive side, it is made solid and I don't expect to have any problems with it. It needed a nipple to connect to the trailer plumbing, and a hose to hose connector so that the hose would connect to it. But so easy and quick to connect, and it did not leak.

Very robustly built. The wall part is made of impressively solid, nicely polished metal, and the hose connector is very solid with the actual sealing being done by replaceable O-rings. The hose connector being separate gives the big advantage of allowing you to attach it to the fiddly hose threads wherever it's convenient to do so, then attaching the whole assembly to the vehicle with a ⅓-turn. The fiddly hose threads are made slightly more fiddly by the need for a female-to-female hose thread fitting, as the threads on the host connector are male, i.e. intended to attach to the input end of the hose rather than the output. Fortunately the adapter you'll need is available all over the place for a few bucks, or even from Aquor themselves for more than a few bucks.

I replaced my old water inlet with the RV City Water Inlet two years ago and it has been a huge upgrade over the old plastic garden hose inlet. The Aquor product is sleek, secure and rugged design. I love the flush design that is near flat with the panel of my Sprinter RV. The exposed stainless steel looks new like the day it was installed. The design is structurally rugged, basically all metal, with nothing to deteriorate. The use of a design specific connector ensures that no foreign hose is inadvertently hooked up to my fresh water system. It is expensive compared to the typical plastic inlets but in this case you get what you pay for. Thanks Aquor for providing a superior product. John Y

I got this for my Sprinter van that I’ve built into a camper, and it works great to fill the 20 gallon water tank. The hydrant body is solid and very well made, and the hose connector fits seamlessly to prevent leaks. Also, I like that you can control the water flow directly at the hose connector by turning the ball valve. The only thing that was a hiccup was that the I needed to go to Ace to get a female to female hose adapter since the Aquor hose connector fits the wrong end of the hose. I emailed Aquor to inquire about this and they did give me an immediate and thorough response, so I appreciated seeing they have good customer service. The fix was to get the female to female connector, which I did and everything works fine. Minor hiccup. Great product.

This is a well made product. But, for my application I've installed on interior fill for Sprinter fresh water system. I was under the assumption this was going to be a solid solution, but when the hose attachment is removed a small amount of water back-flows. Given this is interior not ideal. If I would have known this I would have stuck with CPC connectors.

I thought it would be hard to install, not the case at all. What I like to point out is the quality, it’s made out of good durable material. I would recommend the inlet come with a nicer cover, paying $85 you would expect a little more. Once I installed it, the fill process was phenomenal. It was easy to connect and starting filling water. It’s the thing you hesitate to buy because of the price, but it’s the valve you end up getting because the rest feel and perform like junk. Free cover holes is what I recommend with this package

I really wanted to like this. Great idea. Only issue I have is when disconnecting, it leaks the water left in the handle and inlet. Probably not a problem if you have it mounted outside but if you have the inlet mounted inside the back door of a van you will have some water to clean up every fill. I ended up printing a drip tray to go under the inlet. (See photo). Other issues is a female coupler is needed to attach to a hose if using for a fill.

The quality is top-notch, and it works very well. I have installed it on an RV as a water inlet. I also purchased the dust protector cap. The only downside I can see to this is that you cannot use the dust cover and the rubber plug at the same time and keep a complete seal. The dust cover also won't shut completely with the rubber plug. So a bit of warning for those wanting the rubber plug and the dust cap. For the rest, the install is straightforward, and it does what it is designed to do with quality and elegance.

Handle broke and now it doesn’t work

It arrived quickly, and I opened it up and it seem very well made. It is heavy metal and the quick connect part is thick plastic. Now to install it and put it to the test

I realized that the spout that came with my Alu-Cab was not as well designed as the Aquor system! I can now fill and drain from this set up! I am very Happy I made the decision to buy this product and have also turned other Alu-Cab owners onto this product and have now installed!

The installation process of Aquor's RV water inlet was straightforward and hassle-free. Clear and detailed instructions were provided, along with all necessary mounting hardware. It is a quality product and its design is remarkable, I suggest to anyone who wants to use it..