Mudder 28 Pieces 3 Pin LED Strip Connector 10 mm Solderless Light Connector L Shape Lights Extension T Shape Solderless Adapter Connectors for WS2811 WS2812B SK6812 LED Strip

These connectors seemed to be fine for the job, unfortunately they didn't work with the strip lights I had (I knew this may have been the case when I bought them) Not a fault of the connectors.

Great, item, does exactly what I needed. Easy to use

As others have commented, they are quite tricky to open (I used a penknife blade to pry the catch). Getting the strip light tape in is also difficult (and will be impossible if the protective tape has been removed from the adhesive backing). So, cut your light strip to length and fit it into the corner pieces before removing the protective backing tape. I found a thin bladed spudger very useful for easing the light strip under the contacts, and the strip is held firmly once the catch is closed. After this cut the backing tape close to each connector and remove it to expose the light strip's adhesive back.

Absolutely terrible build quality none of the pins line up, and the T connector is completly wrong and does not work. AVOID

Bit fiddly. Hopefully they work for a long time.

Exactly as described

I bought these to go around corners for my Tapo light strip. Despite trying in a a few different places, the connections meant that some colours did not work, or did not work at all after the connection. Possibly useful for white LED's but not multi- coloured

Having read reviews which varied from "OK" to "rubbish" then I was hesitant about buying these connectors, but had a need for them and they were about the only pack that were suitable. Delivery was fine (Royal Mail) and in the specified time frame. I did find it hard to open the clips, but that may be as much me as the item itself as once I had got the hang of it then it was quite easy. For me, a downside was that I needed to attach two pieces of existiting strip light to a connector and so the tape was bare, but this proved hard for me (again, probably just me not being that dextrous any more) to get the tape under the connectors and clip the top into place. A few times, one or other side pulled loose. Also, whilst trying to work out how to get the tape in, I had the connector upside down and the three connector pins fell out onto the floor, so that connector now is just for show. That being said, has it done what I wanted / needed it to do? Simple answer is "yes" - I have been able to connect together two pieces of LED lighting and have a full LED strip again. I was tempted to use the corner pieces but as the LED stip works with a slight twist then decided against this in case it caused more problems and I disconnected the new connector again. So, overall, basic but effective and has fulfilled my needs, but these are pretty simple and may not be as demanding as others'. There are three images attached - first of all, the type of tape and the connector required (for me a 3 pin one). The second is a bit blurry sorry but shows the conector with tape in both sides. The third shows that the connection works and that there is a good connection through the connector.

Tolle Magnete

just recently finished up my latest PC build and got a set of LED light strips (Amazon ASIN B08GSCJPMD) for accents inside the case. The LED strips were longer than I needed, and I wanted a cleaner install than 12 inches of loose wire at the junctions for that kit. So I got THIS kit of ARGB 3-pin couplers. The short story: These work! I got my LED strips mount around the inside of the window in my case. I recommend using a powered ARGB hub. The long story: Your motherboard probably doesn't put out enough power to properly run a LOT of LED lights off of a single ARGB plug. I ran into a problem when installing my LED light kit and using this couplers kit. The further along I got, the less the LED's worked properly (I did have a 24-cable motherboard extension kit as well). But the LEDs were doing weird things... They would not light up the correct pattern the AURA software was sending, and the LED strips pretty much wouldn't work after the 2nd junction with these couplers. It's as if they weren't getting enough power. And after a couple hours of trying to make it work using different coupler pieces, trying to modify them thinking it was bad connections (based on some other reviews here), I finally came to the conclusion that they just weren't pulling enough power through the motherboard 3-pin ARGB plug - and I have a brand new ASUS Hero VIII mobo! I finally decided to get a powered ARGB hub (Amazon ASIN B08T1SM5CW) as those draw power straight from the power supply and the only control signal from the motherboard. BINGO! Now with the LED strips and LED mobo cable plugged into the hub and powered by the power supply, all the lights worked perfectly as they should! And all the junctions I used this coupler kit for worked great! Overall these worked great for me. I suspect that others that have issues may be running into a POWER issue, not a connectivity issue. I did make sure the click the white covers down very tightly so they stayed closed. These get a recommendation from me.

Excellent produit facile à utiliser

The pins dont allign with the ws2812b connection points. Either the gnd and the data pin, or the 5v and the data pin make contact but never all three. Worthless product

Fácil de instalar y cumple su función, perfecto.