MOUNT PRO Dual Monitor Wall Mount for Max 32" Screens, Up to 19.8lbs Each

I am very pleased about the quality of everything regarding this mount. On top of it feeling like a good quality mount, it was also packaged very neatly, came with detailed instructions, came with a template, and was not difficult to mount the monitors onto it, all of which are things that you sometimes do not find on other monitor mounts. On top of all of that, the price is not bad at all when comparing what some other sellers/retailers want for their mounts. It was very easy to install it and really only took me about 15 minutes after finding my tools. They are very strong arms that offer good flexibility even in the weird position that it was installed in, and the person who I installed it for is very happy with the way it sits and how adjustable in basically every direction the screens can be. Both monitors are 27 inches and still have room to move around. The mount is certainly a little bigger than others, but not by much and I believe that is an expected tradeoff when getting a dual arm monitor mount versus a single arm mount. And while it is bigger, it is not extremely heavy which was helpful for the installation, and it does hold up two moderately heavy monitors with ease. All that being said, I'm very pleased with the mount and when it comes time to buy more, I will definitely seek out this one again. I would also expect the single arm version of this to be a high quality as well and will also seek out this company for a single arm version.

I used a 1" thick 12x18in board to bridge two studs to allow me to mount exactly in the center of my selected area. I used two Philips 32" Curved Monitors which are each 22.1 lbs. (be advised the rated load for the mount is 17.6 lbs.). It all came out wonderful. I have a row of three monitors on a wall with these two monitors mounted above it. I can even pull the top two monitors forward and down or push them back so they are up an out of the way. I do agree with the seller's notice that all angles will not support the two monitors to be flush in the center (no gap between them). It's going to come down to finding that right angle for the curved monitors to meet and covering up the background with a neutral color so the board in the back doesn't stand out. I found that at many different elevations, if I adjust the monitors forwards or backwards, then I could make them come very close to each other. I did struggle a little with managing the arm adjustments, but this is because I am exceeding the weight limit supported. The arms fluidly move my monitors up down and back/forward and then hold that position without any effort (once I got the right tension settings set).

This was very easy to set up and it's very sturdy IF you mount it to a stud like the instructions say. Common sense would say you couldn't mount in drywall even with anchors because moving the monitors would significantly weaken the anchors. I like the built in cable management caps under the arms...nice added touch. I would definitely recommend this wall mount!

Pls see images: I have two Dell Monitors. Once everything was done, it worked out well enough, but I wouldn't choose this item again, and I cannot in good conscience recommend it for anyone who is not a very skilled handy-person or who wants to set up an easily changed arrangement. 1. As can be seen, I use my monitors with one centered, the 2nd angled to the side. To make this work, I had to mount the arm offset from center because the arms are not long enough by about 1.5" to do this otherwise. I expected this, so it was not a major problem because the wall is a support wall with 16" centers on the studs, and there was one near where I needed it. 2. The real problem is the top-end two-bolt arrangement used on wood studs. You absolutely !_MUST_! ensure the bottom bolt is precisely centered on the 1.5" stud and plumbed (leveled) correctly, or one of the top bolts will not embed in the stud properly [in case you don't already know, most wooden 2x4s are typically ~1.5"x3.5", NOT 2x4]. This could be a major hazard if an electric wire or a water pipe is stapled to the stud because you could end up drilling into or screwing the bolt into it. {To do this safely, use a reliably accurate digital stud-finder that shows centers, check 3 times, then use a level to mark the centerline. After that, use the supplied template to ID the bolt-hole centers and push a large nail or small cross-tip screwdriver through the sheetrock until it meets resistance. Push a little harder to see if it embeds in wood a bit more. If it stops hard, DO NOT force it, try a different spot. You can putty the holes later.} 3. The other design problem is that on sheetrock, the bolts will tighten the base into the wall material if turned to far, causing it to sink unevenly and damage the wall. Basically, to avoid the problems above (and make this a lot easier) I mounted a piece of 1"x7" hardwood on the wall using 4ea 3" sheetrock screws centered on the stud. Then I centered the arm base at the height I wanted and bolted in on. The bolts are long enough to go through to the stud, but not so long they will weaken it (imgs 2 & 3). BTW, the bolt heads are metric and a socket wrench is the best tool for this. *** The non-construction/installation problems I have with this thing are: A. The arm height tension can be tightened or loosened, but the arm position, height, etc. cannot be locked. I assumed the hex wrench adjustment would allow me to lock the height, but all it does is adjust the tension. Also, the front-facing left-right rotation cannot be locked. I can lock the front-back tilt adjustment, but not left-right rotation. Because of this, every time I move the monitors, I need to adjust the height and position, and the adjustment is neither smooth nor easy. As can be seen, I intend to push them against the wall when I need the space and pull them back into place otherwise. It takes about 5 minutes of fiddling and adjusting to get the position, height, and rotation as shown in the first image. Not in itself a major problem, but not what I wanted. I will be making a fitted bracket to put at the top to make this easier. B. Two small issues: - The plastic lower-arm wire-hiding covers are cheaply made and one of them broke when I gripped the arm. I wasn't trying to remove it, just move the arm around (which is a real PITA BTW when there is no monitor to counterweight it). The upper-arm plastic covers are also not easy to install w/ 3 thick wires (USB, monitor, & power) and more would likely not fit well. - The top of the screw that secures the monitor to the arm is really stupidly designed. I have large hands and fingers. The oval shaped screw head is really difficult to grip in certain positions, so I ended up having to use pliers to turn them—another fine example of fixing something that wasn't broken. *** Other than all of that, it works pretty well and does the job okay, but as I wrote, I would do this differently if I had to do it over.

Fantastic mount. Installs in less than 10 minutes!

The mounts themselves are pretty solid, but for anything other than a pair of 32” displays, this setup will leave a horrid gap in the middle for a 50/50 monitor angle split. See photo attached. Since this is a wall mount, the arms themselves cannot physically swivel further back that parallel with the wall, preventing articulation needed to conjoin two monitors smaller than 32”. Universal size support hurts anyone not running the largest physically supported display size.

A must have

I really like the dual monitor mount and works well with my 32" monitors but needs to be mounted direct in front of the desk for a good range of motion. I had it in a corner and with a multi-position desk to sit or stand and moving the monitors to work with that scenario didn't work as well. The only other issue is tightening the monitor so it is straight as it tends to lean down, so had to pull the bottom of the monitor out more and tighten it up and then it falls back into a straight position.

It is a quality product with nice finish and most importantly it is fully adjustable for arm tension in two axes for each arm. I suspect that the reviews where customers said the monitor was dropping hadn't adjusted the arm tension

ثباتها حلو من عيوبها تعطي ميلان في الشاشه بسيط ولا له حل المشكله ، والعيب الثاني في الصور الواضح لي اني يمديني احرك الشاشه ك عموديه او طوليه ويوم جات اكتشفت ان ما يمديك

ist eine gute Hilfe den Arbeitsplatz aufzuräumen und praktisch zu gestalten...

Doesn’t work well for big screens at an inside corner (arms aren’t long enough), but they work on a straight section of wall.

I have 2x 32" monitors mounted on this and it's solid as a rock. I have a stand up desk and it's so nice (and easy) to adjust the positioning. I've used now for some time and I had to make my first "tightening" adjustment, the provided tool makes it easy.