Master Airscrew Stealth Propellers for DJI Mini 2, Mini 2 SE, Mini SE & Mini 4K - Black, 4 propellers in set

I like that it makes it easier to see. The noise is definitely different if not quieter.These are a little rough around the edges, I used sand paper and a deburring knife to take the rough spots out. They are a little longer than stock, I noticed, and also don't seem as brittle.For this price they should give you 12 (two spares for CE and CCW).Would buy again though!

Have bought these before and I’ll keep buying them. They are awesome look great and perform great. Try them once and you’ll order 2 more packs asap. They break on crashes like all the rest but they definitely perform better so if you fly like me grab a few extra sets of these and hope you don’t hit things as hard as I do lol. Dji got me covered for the win😅

Edge flashing, (extra edge plastic) for the mini2 needed removal with fine sandpaper, using caution not to remove more than the extra plastic. When spinning the props weigh many times more and both sides need to be as matched as possible.More importantly the new blades fit very tightly and need to be lose enough to straighten out fully when spinning or there is major vibration, motor bearing loading, noise and possible erratic flight characteristics. A tightly rolled up half inch or fine sandpaper works to clear the mount holes if needed.And, noise pitch is different and noticeably quieter, especially when hovering above. If you know to prep the props. There should be no noticed vibration.

I put the propellers on perfectly, double checked even considering there was not clear instructions included. You can tell which propeller goes where by I small line near the spot to screw each near the motor. The drone hovered 5 ft in the air (a little uneven) as soon as I lifted the drone to 15', it immediately uncontrollably hooked in a dog leg right path into a swampy marsh and thankfully for stuck in a tree vs water below to recover. Surprisingly no blades were damaged, so I tripled checked the positioning of the blades and experienced the same results. This time several propellers were destroyed, but the drone survived. I put a back-up set of factory propellers on the drone and it works like a champ again. I've purchased plenty of aftermarket propellers before with no problems, but something about this type is not compatible with my DJI mini 2. I wouldn't take the risk. The feeling of excitement to try an "improved set of propellers was ruined by the experience of almost losing a $600 investment twice. Back to the factory models blades for now. I'd recommend trying these in a padded safe place first if your going to buy them. I even brought them to a local known professional for evaluation, apparently the shape/ sharp angle of the cut in the propellers caused the drone to react the way it did. I don't like to share a negative experience and give items the benefit of the doubt, but want to warn anyone to be safe and would not advise for the mini 2 , perhaps they will work for another drone! Good luck. Otherwise, shipment was great, quality felt great and the appearance was perfect; they didn't work for me.

Shipping was fast and service was excellent.. However, I have been unable to use them since they do not fit the Mini4k.. Perhaps I ordered the wrong size? But the description says they'll fit the mini4k(which is basically a mini 2se/mini2).. I'd still like to try these but in the proper size/specs... Have heard good things about them.. Will be returning them for for the proper size if available..

They fit, and that is the best thing I can say about these props. And, the Mini 2 flies after installing them. The Mini 2 was stable while in the air.I cannot recommend these to anyone, they are NOT quieter than the OEM DJI props, they do sound different, the pitch is lower, but the overall volume is not lower. I fear that there is a lot of expectation bias in most of the YouTubers that say these are quieter, they expect them to be quieter because they are told it is quieter but not a single review on YT actually measured the volume levels.Another issue with these props are the lack of quality control. Three of the four props had a considerable amount of flash around the edges. You would not expect a company that say they are a leader in hobby props would sell a product that looks like it never went through QA.One last issue is that the actual material used to make these props is very fragile and brittle. Any small bump can result in large chunks of the prop breaking.Would I buy these again? In one word NO. Would I recommend them? Again the answer is NO.

I bought these because the description said it would give 3% more flight time and make it 30% quieter. I can tell you that it gave me a bit more than 3% and it made my dji mini 2 sooooo much quieter. I will definitely order these as replacements again.

These don’t seem any quieter than the stock propellers and I really see no advantage to them. They look cheaper in person than in the pictures. They’re also brittle and easily damaged. I wouldn’t recommend these considering the up-charge versus standard replacements.

Bon service

Me gusta el color en combinación con mi drone , el team del ruido en realidad no es notable la diferencia pero se ve muy bien

👍

I’m not sure they are much quieter than the standard blades, but they are nicely made and packaged.

Very posh looking blades, good value, I gave 1 a test fit, yes they fit.