NewYall 8 inch Sync 2 Navigation Radio Touch Screen Glass Digitizer

My daughter's 2012 Ford Explorer Limited touch screen wasn't working, though the video display seemed to be fine. After watching a few YouTube videos, I ordered this touch digitizer to replace the original one. Much better than the $1000+ the dealer wanted to fix it. Prying off the side trim was tricky but doable. Just be careful and get some plastic pry tools. The side trim comes off from the inside edge. The top clip needs to be pushed outwards, the others just pop off. The larger trim (with AC vents on top and control buttons on the bottom) then comes off easily though be careful with the top. There's one plug to remove the large trim unit. The screen unit comes off with four 7mm bolts. One of the plugs comes off easily, the other I was afraid I might break it. So rather than unplugging the screen unit from the car, I left it all connected and removed the four M4 Philips head screws on the back of the computer/heat sink (heavy part in back with fins) and separated the screen unit from the computer unit. It just snaps off if you pull it straight off. Four torx screws (2 top and bottom, T10 I think) allow separation of the screens from the screen control unit. There is no need to remove the 4 T15 Torx screws on the sides, they just hold the mounting brackets that attach to the car. Remove the metal frame to get access to the touch digitizer. I disconnected only the digitizer, and left the screen ribbon cable connected because I couldn't tell how best to detach the screen ribbon cable, and it wasn't necessary. Then, using a single edge razor blade, I separated the screen and the touch digitizer by running it around the screen between the digitizer and the LCD display, and then used the razor blade to remove the sticky tape residue from the top and bottom edges of the original screen. I didn't bother with the sides, since the new unit only has sticky tape on the top and bottom edges. After removing the protective film from the back, and then exposing the sticky tape, the screen fit right in place. The new digitizer plugs in where the old one was. I then removed the protective film from the front, and put it all back together with the 4 Torx screws on top and bottom. The screen unit then snaps back into the computer/heat sink base, and attaches with the 4 M4 screws removed earlier. It then mounts to the car with 4 7mm bolts. Plug the large trim unit back in and reattach it, and then check that it all words before replacing the side trim. It worked first time.

Replaced broken touch screen on 2016 Explorer Sport which has sync 2. Cheap and next day delivery. You do have to cut old touch digitizer off the old screen. Just use a sharp blade it’s very easy. Don’t let this scare you away. It’s an easy install. Worked flawless for a couple days so far and screen looks brand new where you normally wouldn’t have noticed it didn’t look new anymore. This is only the touch screen sensor, your screen should still be working this is not a new sync screen that you are purchasing. Your screen still needs to be on and works behind a broken touch screen, that’s how mine was broken before this repair.

Doesn’t fit a 2016 king ranch f150, maybe I should’ve got the sync 3 screen?!

This was a direct replacement for my 2015 F150 with the sync 2 larger radio. Touch screen is working again. Installation was easy, just some screws and buttoning everything back together. The digitizer works well, it is a little shinier than OEM I think, but not in a bad way, I actually like it. For the price, I have zero regrets as of now, hopefully it lasts for a while. Much better option than upgrading to sync 3 for $700.

Worked perfect for my 2011 Ford Explorer Limited. Touch screen would not work at all and after watching a youtube video on how to install it works perfectly. Probably spent about an hour total to get it setup.

Perfect replacement, a lot cheaper than buying a whole radio and it works, bought this over a year ago and the radio still works great

Easy to install and seems to be a quality screen. I’ve had it installed for a few. On the now and it works perfect. Only con is the screen is very dim in the daytime and you can’t see the screen when you wear polarized shades.

Installed on 2013 Lincoln MKS: Relatively easy install, especially if you’re familiar with tech repair. Works exactly as it’s supposed to. It also looks a lot better than the stock digitizer that comes with the system.

Precio vs calidad muy parejo. Cambié mi pantalla sin problemas.

Bought for a 2014 f150 with a dead touch screen, the screen displayed just fine but the touch didn’t work. You don’t need to buy the adhesive strips that they suggest bought together because this screen comes ready to install. Did it super easy and the screen worked just fine after, no recalibration of the touch required

Hice el cambio del touch screen porque ya no me funcionaba. Este funciona perfectamente.

Package is will protected, double sided tape in place, connector fit in the plug without issue, and worked immediately without needing to calibrate.

Se ajusto perfecto a la pantalla de edge 2011