Vacbird Upgrade Vacuum filament dryer Kit with USB Pump, 3D Filament Storage, with 10 Single Roll Filament Vacuum Bags (30 x 34 cm)

Nice simple little filiment bags and sealer. The pump comes with a usb a & c so you can even run it from your phone. The bags are a nice size and easily fit a 1kg reel in. Not a tight squeeze like some others and the pump is simple to use just put I over the blue disk and press the button. I found the easiest way was to make sure it's on a flat surface. The bags are well made and not just a cheap freezer bag with a valve. Would highly recommend it as a inexpensive but excellent way to keep your reels in good health

I was in the process of getting a two reel drier when I tripped over this product The bags are substantial and easy to seal and the vacuum pump is well designed and effective Now, I only need a one reel drier and keep dried filament in these bags All in all, this is an excellent product in that it is simple, inexpensive and effective

Pretty good so far, better than the manual pump. Worked with my existing bags. Supplied bags although take a 1Kg spool, its very tight to get in.

Wasn't sure how this was going to work, but I think it is priced well. I am happy to report back and say it works better than I expected. When applying the pump onto the aperture of the bag it needs a little moving around to get the right spot. But when you've got the right position, it takes seconds to evacuated the bag and get a vacuum seal. What I was looking for was leakage of the bag. But 2 weeks later, none of the bags have leaked. So it turns out this was good purchase. I have LOTS of filament rolls! But after drying, I'm left hoping the little gel packs will do their job. Now they have gel packs and vacuum packing. Also, it remains possible to see which filament is which after sealing. I'm a happy customer. I just need a load more bags now!

I tried this because I've an increasing number of filaments that I swap between. In use, the pump needs to be powered from a 2A capable USB port, something that I didn't immediately spot. Most of my USB wall chargers would therefore not drive it so I had to buy an extra charger. The pump comes with a USB-C connector and I didn't immediately realise that there is a standard USB-A connector (used in most wall chargers) available by unplugging the USB-C connector. In use I found it difficult to get the pump to connect to the valve in the bags and it isn't always easy to get the bag to seal. My other solution is to use desicant (silica jel coulour changing beeds) in a plastic container. The containers come from the local petfood store filled with fat balls to feed the birds - these are cheap enough that the bird feed is effectively free! One drum typically holds three rolls of filament and provides a quicker way to swap and dry filament. I guess the local birds are going to be getting well fed over the winter...

Bags are fine, but the pump is absolutely useless spent ages trying to suck the air out with it and nearly burnt it out 😂😂.

Pleasantly surprised with this. Watching their video, didn't think it would suck that much, but I think they're demonstrating incorrect fitting or something in the video, cause once you get it right, it sucks the air out pretty quick (obviously get as much out as you can first!). The great thing about these is that the valve is flat, virtually unnoticeable, unlike some others with a massive plastic cap - so they fit nicely back in the filament boxes (they always seem tight fit so I didn't want big plastic valves) Some people seem to have trouble getting the 'seal' right, but I haven't had a problem. Just put 3 fingers either side of it underneath, and you can hear the sound change. The pump is very nice too - has a USB-C adapter built in to it, and nice finish, nice cable, and nice fancy rubber cable tie. Bags seem very good too. I have some filament sealed up for a week now, not noticed any leakages.

Bags look ok, as expected. The pump is great! It's USB powered, rather than rechargeable, but that's fine. I bought it as I was fed up with the manual pumps I have, and oh boy what a difference it makes! Easy to use and does the job in 15 seconds or so. Power is via USB-C, or standard USB-A, which is helpful. Very pleased.

Great small and nice pump - works well with all the vacuum bags .

Super produits

Ich bin sehr zufrieden mit dem Vacbird 3D Drucker Zubehör Upgrade Vakuum Kit. Das Set enthält 20 wiederverwendbare Vakuumbeutel in der Größe 30 x 34 cm, die perfekt geeignet sind, um 3D Filament vor Feuchtigkeit zu schützen. Die USB-Pumpe funktioniert zuverlässig und ist einfach zu bedienen, was das Vakuumieren der Beutel schnell und unkompliziert macht. Besonders praktisch finde ich, dass die Beutel wiederverwendbar sind, was nicht nur umweltfreundlich ist, sondern auch auf Dauer Kosten spart. Das Vakuum schützt das Filament effektiv vor Feuchtigkeit, was die Qualität meiner Drucke deutlich verbessert hat. Die Verarbeitung der Beutel ist hochwertig, und die Größe passt gut für die meisten Filamentrollen. Insgesamt bin ich sehr zufrieden mit diesem Upgrade-Set und kann es jedem 3D-Drucker-Enthusiasten empfehlen, der seine Filamente optimal lagern möchte.

Buenas bolsas para filamento, al principio cuesta un poco coger la dinámica de vacío, pero luego lo conserva muy bien y lo mejor, es que es reutilizable.

İş görüyor