amFilm 3D Curved Tempered Glass for S22 Ultra Screen Protector Samsung Galaxy 5G 6.8 Inch, Fully Compatible with UltraSonic Fingerprint Scanner and S Pen, Upgraded Easier UV Gel Application(2 Pack)

TLDR: Stop shopping around - this is the protector you should get for your S22 Ultra (my wife has the S22 version and it's also great). UPDATE: After 6 months of having this installed I just accidentally tested this protector by dropping it on pavement screen first. The screen protector was so badly damaged I thought for sure my phone screen was toast. But I was wrong! My phone is perfectly fine. Combine that level of protection with the fact that after all these months there was no air bubbles or peeling - this is definitely the best screen protector I've ever seen. I have used several different types of screen protectors over the years. But lately they have just been awful. The last one I bought for my Note 20 was so bad I sent it back. Too bad too because I dropped my phone a week later, which is how I ended up with the S22 Ultra. This protector exceeds in all the important ways: successful installation, fingerprint reader compliant, and protection. First, the installation is not quick. Set aside 15 minutes. It's okay though - take your time and it's hard to screw it up. No air bubbles to iron out. No corner that's not flush. None of that. The guide they provide to facilitate installation makes this install lengthy, but in the end, you have a screen protector that fits PERFECTLY! Second, the installation actually takes the fingerprint reader into account. There's no weird circle or air gaps. I did have to reprogram my prints. But after doing that, the reader works just as well now as it did pre-install. Finally, this provides a nice shell of protection and is secure around the edges. I'm not going to drop my phone just to test this, but so far, no scratches and I feel better knowing my screen is safer now than before. I have tried at least 5 different types of screen protectors over the last 2 years (between my phone, my work phone, and my wife's phone) and these are so much better than the competition I feel like they should be in a different product category. Nothing else even comes close.

I've tried many screen protectors over the years, this one is leaps and bounds better than its competitors. I watched the installation video 3x. During the process, I was doing this on my office desk and my cat jumped onto my lap at the worst time, (this 3 legged cat wanted to help) got the UV adhesive everywhere but on the screen. The way you remove the UV adhesive if it gets on the floor, if it dries, is with the UV lamp. But mine got on the floor via a freak event, totally my fault So I tried it again but his time on a granite countertop with my 3 legged buddy on my lanai. 2nd time it went flawless and it came out prefect, I didn't need to recalibrate the fingerprint reader, thanks to the kits installation metal fingerprint dome cover, this kit is well thought out and the mechanism to instal it is simple to use, and idiot proof if you follow the instructions, but not curious cat proof. No bubbles, no flaws, you cannot even discern if it has a tempered glass cover, nor does it compromise sensitivity, the S-pen works in normal and air mode at the same distance as without the screen protector. I asked amFilm if they would allow me to buy two more tubes of UV adhesive for future use since this was a two pack, instead they sent me a new kit, what a great company (and product) PS I needed a quality screen protector, as I just bought a stingray cellphone case, normally I use a Otterbox Defender Pro. While this stingray case is stunning, it offers almost no protection, so this tempered glass screen is needed. My newly adopted 3 legged cat is sorry he screwed up the first go, but cats do what they do.

The video shows them installing the screen protector very easily, however, if you are like me and very anal about perfection when it comes to your electronics then you are going to take as much care as possible to install anything onto your electronic device (whatever it may be, in this case it's my Samsung S22 ultra Flagship phone). So for it to still come out incorrect is quite disheartening. When I purchased the screen protector it stated that if I showed proof of purchase then they would send me another screen for free if the install had any bubbles left on the screen. Well the very first one that I installed did exactly that, on the top portion of my screen there was a bubble and even though watchig videos and taking the companies suggestion of giving it 24 hours and the bubbles would work themselves out, it did not. So I was stuck with a awful looking bubble on my phones screen, now for some that may not be a bother, however, for me who loves his electronics and wants perfection out of his devices, whether it may be aesthetically or not, that is far from what came out. I told myself that this may have been my fault that it came out the way I did it so I did not write a review as I am now, instead I just followed the companies suggestion of registering the product and stating what had happened and that they would send out an extra glass replacement. Well I did that and I NEVER received the extra glass. Well months went by up until last week when due to me dropping my phone I had to change out the glass. I was excited because I had told myself that this time I would be able to make it perfect (Note: The first install wouldn't allow the fingerprint sensor to work, and I placed the weight on there as the company video showed). Videos I watched showed that the screen removal was very very easy, like eating a piece of cake. Well, what the videos don't show you is a screen protector that needs to be replaced due to breaks in the glass. God forbid if that is the reason why you have to replace the screen for, because let me tell you, it was a complete nightmare. It literally took 4 different 2 hour sessions, 100% alcohol, gloves (to keep from little broken glass pieces going underneath your nails) and a lot of patience to remove the original screen which hadn't even been smashed into pieces. Simply the top right corner had cracked a bit. So now for install 2, I watch the video again, I even went as far as doing this after a hot shower so that there wouldn't be any LINT, DUST OR ANY OTHER DEBRIS in the air. I followed the instructions EXACTLY! I was excited to place the new screen onto there, I saw visions of a smooth and beautiful screen WITH a finger print sensor that would work this time around! So I began my task at hand, *Warning* Graphic Content Warning, proceed at your own risk. I went as far as not wearing any clothes just to make sure Dust or lint would not come off of me onto the screen, then I began the lengthy process of applying the glass screen protector onto my S22 Ultra (The process probably takes a lot less time to install if you're not a perfectionist like me) I followed the instructions exactly as they do it. I watched the video simultaneously and was pausing the video as I needed during each step. So once again I get to the portion where I need to remove the tabs from the top and bottom slowly to allow for the glass to sit onto the screen, well just like the time before I removed the tabs slowly and as the screen sits onto the main S22 Ultras screen and you see the glue begin to spread and the glass sucks onto the main glass, suddenly at the middle of the phone and another off to the right, one below that one and to the left 3 total bubbles form. Now keep in mind that these bubbles are NOT at the same place the last one was. So all in all I have to say this product does not apply easily as they state and it surely does not remove easily (however, I'm not sure if they made that statement or not. The removal is my personal opinion.). Also, when I applied the second screen the phone dropped from a height of about one and a half feet ( I was sitting down, leaned forward on a lazy-boy playing a game and I dropped the phone, No more then a 2 foot drop, and the second time it cracked at the top right corner. Oh and I have a Speck case that is drop tested). I hope this review will get the attention amfm and they will make this right with me, as I never received the initial screen that I sent in for. I followed there instructions as well, yet nothing. I will update the comment when and If they reach out to me. Would I recommend this product to friends or anyone for that matter, at the moment NO! Am I happy with the product I spent 40 dollars on, NO! It's all in their hands from here on out. Thank you

I have to say that I'm a huge fan of amFilm in the past and this product does not fail to deliver in almost all aspects with this screen protector. Only a few minor flaws holds it back from 5 stars First off, the packaging is fine. No complaints BUT the glass does have tiny little stand offs that freaked me out the first time I saw them (I thought dust got underneath the glass somehow). The friendly customer service reps explained what they were and I'm happy to report the stand offs do melt once the glue touches them. The install process is mostly straightforward but a tiny bit more convoluted than I would want. In my experience most glass protectors have some kind of tray you set your phone on with the camera cutouts so it can lay flush on your desk. Instead this one opts using two foam tabs you have to stick to the back of your phone that keeps it level and then an additional tray to align your phone. It also requires you add glue to both the top and bottom of your phone, then sliding two wedges out from underneath the protector and into place. While anyone who is experienced with UV glue installation would probably be able to get it right, I do worry a bit about the install process and can definitely see it as a bit daunting for a first time installer. Good thing it comes with two! The UV light is very strong but lacks an auto off timer. This means that you must babysit your phone during the curing process and the UV tray can get very hot if left on for too long. An auto off feature would have been nice but I never left it on longer than recommended. Finger print reader works just fine. Not as sensitive and fast as bare screen, but a tiny trade off for the increased layer of security. I've had some other comeptitors products and honestly this one feels great in comparison. Once installed the screen looks mostly great. The cutouts work perfectly with the case I'm using (Spigen Cryo) and I've had the screen on now for over 2 weeks with no signs of peeling as I did with other cheap competitors products. However, I did notice light haze and streaking underneath the glass the first week or so after installation. I also observed a very noticeable yellowing around the fingerprint reader. While it is very faint in my picture, in real life it's pretty obvious under bright screen conditions (but gone if watching videos or playing games). It's mainly visible when browsing web pages, texting, or scrolling through social media. Most of the streaks and hazing went away after about a week but the yellowing has persisted and does not seem to be improving. Other than that screen clarity and color reproduction feel almost as good as bare screen. At the end of the day the flaws are minor and I'm happy with my purchase. The protector helps provide me peace of mind. I definitely recommend amFilm's protector over the competition.

When I bought my last phone, an S10, I also bought an amFilm glass protector. It was great, but the fingerprint reader sucked with the protector on. Fortunately, this time around I was super extra careful and got a near-perfect install, including the fingerprint reader! Installation - 3/5: Installation was the same as the S10 protector. There are a lot of steps. I've included tips at the end. I double checked the positioning of the UV glue application spots, triple checked the bubble level, quintuple checked that there was no dust or lint, and very very carefully pressed on the protector and very gently repositioned it (<1 mm) to where I wanted it before performing the UV cures with a timer. Screen/bubbles - 4/5: No bubbles, dust or lint whatsoever! Just a few small spots near the status bar where there's some very minor discoloration on bright solid colors, but I rarely notice them. I actually used three dust removal stickers to get rid of even the tiniest speck of dust I saw on the screen, which worked out great. No bubbles whatsoever if you apply the glue properly (READ/WATCH THE INSTRUCTIONS FULLY). Touch sensitivity - 5/5: No issues with sensitivity, and didn't need to increase sensitivity. Fingerprint reader - 5/5: Most importantly, the installation went so well I didn't even need to redo my fingerprints. I did for posterity, but it works just as easily and quickly as it did with a film protector or no protector on. TIPS: - WATCH THE INSTALLATION VIDEO TWICE BEFORE STARTING - To reduce dust, set a bright light behind the phone so you can look for even the smallest speck. Use the stickers generously. Work in a low-dust area, or run a humidifier/shower. - When applying adhesive, make sure the phone is perfectly level or it will run a little. Apply glue where the instructions recommend. Apply the protector evenly. - Make sure the protector is seated within the tray before pulling the stops out, as it might catch on the side. - The protector might be slightly off-center, so you can wiggle the protector very slightly (<1 mm) or tilt the phone to center it before UV curing. - Test the UV light first. I used a battery pack so I could work away from a power outlet. - Don't forget the second cure after removing the weight and fingerprint sticker. I think some people forget to so they end up with circles/crystals/bubbles around their fingerprint reader. - If you have issues with your fingerprints, remove and re-add them to your phone. Do so while your fingers are dry (wash with soap, dry, then let air dry) for best results as dry fingers cause the most issues usually.

Hopefully you read the reviews before you buy this. Putting on these hard protectors always makes me feel like I'm doing surgery. Why does it have to be so complicated!!!! First, if you buy this, look at the UV light before doing anything!!!! Plug it in and make sure it works!!!!!!! If it is missing the slide button like mine did in the image, then return it! If you didn't see this review and you already have the glue on (like I did) then skip down to the bottom of this review. I'll tell you how to get it working. The kit - It has everything you need except for a USB-C cable. Make sure you have one close by and it is long enough to reach your flat surface. The instructions are OK, but need some more detail. Put a paper towel under the phone before the glue. There was too much and it got on my table underneath. On that note, I put tape on my ports and buttons because of the glue run over. Might save you some headache. Hate to see what would happen if it got in your USB-C port. If you look at of my images, the tabs slide in the grooves and the arrow on the tab is facing up. Run them back and forth before putting on the glue. Some small plastic debris flakes off. Use the sticker to remove them. Important - when you empty the glue on the phone, keep it very close to the phone so air bubbles don't happen in the glue. Also, inspect the glue closely. If you see any dark specs in them, try to use a qtip to remove them. They are pieces of plastic from the glue vile. If you leave them you will see them under the screen. Pull the tabs slowly and evenly at the same time. Watch to make sure the glue spreads to all areas. If you see air bubbles anywhere, let it sit awhile. Sometimes they will move away. If you still have air bubbles, do not use the UV light yet. If you have to lightly press on the protector then you should. If you still have air bubbles, you may have to lift it or use the 2nd kit. After I used the UV light the screen worked perfect with no touch sensitivity issues. My finger prints worked just as well as it did without it. I did not turn on touch sensitivity in options. HOW TO MAKE THE UV LIGHT WORK WITHOUT A SLIDE SWITCH - Like a few other reviewers, I was sitting there with the glue on my phone and no switch on my UV light. I took a pair of pliers and found the contact on the electrical board that lit up the light. I held it with the pliers until the UV light set the glue. You can see in the pics that I damaged the plastic squeezing the contact with the pliers. Hope this helps. It's a good protector with poor execution on the UV light and instructions.

First, I have used several brands of screen protectors. There are basically two kinds. Ones like this that bond completely to the screen, there are only a few of this type or ones that use adhesive on the edges. Most of them are the second type. The quality of that second type vary greatly. Their customer service policies also vary greatly. Most of them are very hard and difficult to scratch with metal objects like keys, a few use cheaper glass that scratch easily. They vary in thickness, so some crack more easily than others. Some are cut accurately and fit well, while others can interfere with the camera or haveclios that catch on clothing or even skin. But there is one thing they all have in common, they leak moisture. Some will get moisture under the glass just from facial sweat. Some will get moisture if you drop it in a full sink or a swimming pool. ALL of them will flood of you go into the water with them. I fish and go rafting. Every screen protector I have had has leaked if submerged for more than a few seconds. This screen protector, which is bonded to the screen, does not leak, even if I take underwater photos with it. But there are more advantages with this type. If the screen is adhered only on the edges, there is a tiny airgap between the protector and the screen. This makes the screen less sensitive. This may not be a huge issue if you are just tapping, and even swiping will usually work, but if you have a pen, stylus, or finger print reader, it gets worse. Most people eventually do recalibration and adapt themselves to the loss of sent sensitivity. HOWEVER, that tiny gap also creates an impact with the screen and some types of drops will still break the screen. Without exception, I have broken the screen on every phone I have owned over the last 10 years. Some look asted a month, a few lasted a year, but because of my active lifestyle, I have never traded in a smartphone without damage... Until now! The bonding agent on this screen protector remains slightly flexible. I have dropped my Samsung S22 Ultra countless times. The phone is still perfect. The screen protector itself lasted over a year and a half. Eventually it cracked. But bits of the protector remained on the screen and continued to protect it until I was able to replace it. Removing the old glass was simple and I think I may have spent 20 seconds removing all of it. The bonding agent remained on the protector and the phone was spotless. I put a new protector on using the cleaning pads in the kit and no further effort was necessary. Nothing has ever worked as well as this. I can't speak for the Whetstone brand, Wich uses a similar technology as I have never used that one, but thisisthe best I have ever used. The curve is perfect to my phone. The cutouts are also perfect. There is a a fraction of a millimeter margin between the protector and the phone frame. It is very tiny and allows you to attach a case.to your phone. In spite of some comments I have read, you will not notice it when you use the phone and it does nothing to compromise the protection. I would say the gap is about the the thickness of a business card. Once you are using your phone you will not notice it and not a single person who has handled my phone has noticed it. In fact one person after seeing the scratches on my phone case asked why I was not using a screen protector and I had to show them the margin which the had not noticed. Of course everything has a downside and this product is not an exception. That down side is the installation is not as easy or as fast as the other type and one must be careful to follow the instructions carefully. When I received my first kit, which includes two protectors, it was defective. There was not much adhesive is one of the tubes and no matter how long I waited or how I tipped the phone, I could not get coverage. I would estimate that the second tube had only about a third of the adhesive as the first one. On my second attempt, the tray would not release the sliders and when it let go it made a big mess and the bubbles could not be removed. So I had to contact the company. No problem. Perfect customer service and they immediately sent replacement glass and the supplies to install it. I had trepidation but it was unwarranted as the install was a snap. I threw away the old guides as the new ones were smooth and easy to use. Pros: Excellent customer service Nearly impossible to see once installed. Does not affect screen sensitivity. (I did not turn screen sensitivity on nor recalibrate). Will not flood. Superior protection Does not shed glass splinters if broken Cons: Installation required carefully following instructions Written directions could be written better (Definitely watch the video). Installation takes 5 to 10 minutes (Vs others which take 60 seconds) Not the least expensive solution available. So what will my next protector be? Without any doubt, this one again. In my estimation it is worth the few extra minutes and the extra cost.

Application instructions are easy to follow and once complete the protector is practically invisible on my screen. No bubbles or peeling and I have had it on for months now. Touch sensitivity on my screen is great. I drop my phone all the time and there's barely any evidence on the protector. One thing of note is that sometime after I put it on I was trying to scrape some crumbs/dust out from the creases of my case by the edge of my screen and my nail accidentally slipped and pulled up a tiny bit of the upper corner of the protector, which I was unable to stick back on because the sealant had already been separated. But what I can say from this mishap is that the protector leaves no residue on the screen at all as the glue sort of becomes like a gel once it's dried. Also, having cut off the piece of the corner that was peeled off so that it wouldn't catch on anything and peel further, that corner has not peeled back further at all, even though it has been compromised. So even if a piece gets peeled off, the rest of the protector will stay on just fine, and I think that speaks to the quality of the glue and material. I haven't had to replace this one with the second one they provide in the box, and honestly I'm not sure if I ever will. EDIT Nov 26 2023 (original review in Jan 2023): I still have not replaced it, peeled corner and all it is still on my phone. I've dropped and scratched up my phone throughout this time and there is one noticeable scratch and 2 or 3 more subtle ones, as well as a second area where I dropped it and the protector cracked and chipped off a tiny bit on the side of the phone as it collided with stuff on the way down, but not enough to bother me to replace it. I mean seriously this protector is a TANK.

TLDR: Excellent, very high quality screen protector, 100% recommend, but you MUST FOLLOW INSTRUCTIONS! My biggest criticism: adhesive buildup did fall off of the applicator nozzle and into the adhesive bubbles, but that problem was easily fixed fishing it out with toothpicks. This screen protector is excellent. The tempered glass feels very similar to the s22 ultra's gorilla glass, and there's ample room on the edges to accommodate most if not all cases. You have to follow the instructions exactly! It is absolutely essential to make sure the screen applies correctly and that the application lasts. Every piece of dust must be removed, and after making sure the screen was 100% clean, the application process went very smoothly. Another thing, there may be adhesive buildup around the nozzle of the applicator that can fall off and sprinkle into the adhesive bubbles, so clean the nozzles before using them! But if it happens, use toothpicks to fish the pieces out, I did so and got excellent results despite the hiccup. Again, make sure every single piece of debris is removed from the screen, small pieces of dust that you miss will inevitably make their way in, but that's unavoidable. Another tip: add another 30-45 seconds to the last half of the curing process to ensure the adhesive cures fully. Long story short: pay attention, be meticulous with following the instructions, and you'll have an excellent experience with this screen protector. Bubbles are often due to user error/missing debris that have fallen onto the phone prior to application, and lack of adhesive durability may be due to inattention to the instructions of the curing process, so eliminate those variables as much as you can. You have to be very precise and follow the instructions exactly. For the fingerprint sensor, as expected you will need to reprogram your fingerprint for the best results, and press with a bit more pressure when unlocking your phone, but it is something you do not notice after a day or two of regular use.

I've pasted Whitestone dome glass on my wife and my s22 ultra the first day when we got the device, and is having fingerprint unlock issue since then. But because of the premium price we've paid for the glass, we thought to turn on face unlock instead and let the glass stays on the phone for at least 5-6 months before we changed to another one. However, the fingerprint unlock issue had been such an annoyance that I changed to a local brand, which many reviewed that the fingerprint unlock works, but it doesn't worked for me. I bought two pieces, one for my wife and one for myself, end up I used up both pieces, they are not any better than the Whitestone dome glass. I saw amFilm while searching in YouTube on reviewed for tempered glass installation for s22 ultra, and decided to give it a try. Amfilm didn't disappoint me, it is definitely the best ultrasonic fingerprint unlock compatible tempered glass you can find for s22 ultra! I found that the unlocking speed is no different from naked screen, I'm so happy that I bought amFilm! 😄

Fingerprint is working as mentioned.

Es excelente el producto, bien puesto pareciera que no trae nada el celular. IMPORTANTE! Poner dos botecitos de pegamento a cada cristal, de lo contrario se despegará al poco tiempo. Recomiendo ver la guía de instalación de YouTube de DOMEGLASS y no la de este producto, porque van a quedar burbujas, no presionen la zona de la huella con nada porque marcará error, ni siquiera con la pesa de metal que viene en el kit, mejor dejen que se seque bien unas 8 horas antes de presionar el sensor, ya con eso no tendrán problema alguno.

Great screen protector. Works well and although there's a lot of steps in the process, it was quite easy to apply it. One has been in use for 1+ year now and has only started cracking/peeling recently, although I want to point out this user has dropped their phone on tiles many times. The second one has been in use for 3 months now and not a single issue.