KBS Coatings 8114 High Gloss Diamond Finish Clear Watercolor Aerosol, Covers 35 sq ft, 16 Ounce (Pack of 1)

I have had my disappointments in KBS products. The 2k Max is a good coating BUT it only comes with a moderate reducer and that will not work in hot climates at all. It must have a slow slow reducer. The fact they sell it with a moderate reducer in hot climates is flatly a ripoff. They should know better. I have told them. Those who work with clears know this is the single most important factor. Clears require surface melt. In a hot climate, using a moderate reducer, all you get is orange peel.That said, the Diamond Clearcoat Single Stage Gloss is an underrated Clear. It is a single-stage in a world of "YOUTUBE PAINT EXPERTS" OMG, that do nothing more than echo two-stage clears based on one idea which is cross-linking. The concept of crosslinking is that once cured you can spay something on top of it. That is a fallacy. Spray clear on a prior clear and you could get lift off and peel from hell. And sometimes with 2k clear, it can peel off in sheets for crosslinking on the surface of a prior coating and not adhering. 2k Clears can surprise in a very bad way.I don't care what two-stage you use, you can easily get a solvent reaction while wet. The Diamond single stage is moisture cured and I have never had it react to a cured surface including INDUSTRIAL ENAMEL. Try to remember that Picasso loved industrial enamels. They have a richness lacking in any other kind of paint. I digress.The Diamond Clear in the spray can be used to remedy bad or non-adherent clear. It can be used to spot flaws after spotting in some basecoat or paint coat. It is amazing how well it does in these kinds of applications. On Youtube the idiot will tell you to sand down the entire door panel for example. I say that's nuts. Spotting flaws works great. Breached edges are where you get into difficulty.It is possible with the spray can to get a little overspray. That is where the 1000 sandpaper comes in. It will smooth the miro orange peel easily. If you are going to do large areas then buy the Diamond Clear in a pint or quart and use Thinner or Xylene ONLY and 10%-15% is normally adequate. DiamondFinish Clear can be thinned up to 30%. Thinning helps it flow but it also helps it drip. Remember Xylene is a solvent so it can react with undercoats. So I don't recommend thinning. Just keep your wet edge and it will melt nicely. Any overspray can be easily tamed by 1000 sand and an orbital DA.While KBS claims it is clear that is not actually true. It has a slight amber cast if put on at 2 mils thick. In Hot climates, I encourage 3 mil thicknesses and sanding before buffing with 1000, 1500. and 2000. That will make buffing to a marvellous plastic shine and enough thickness to block UV. Try to remember that Clear obtains its UV protection by thickness, not some pretend additive to block UV. No such additive exists. So it must be thick. Hot climates are full of cars with peeling clear. Hoods get direct sunlight and under the hood the engine gets hot. So go thick in a hot climate.I say that Diamond Clear single stage is vastly underrated due to a large amount of noise made by the "car painting youtube crowd." These are clowns that think a $500 spay gun makes you a pro. There is no truth to this or a thousand other myths. Diamond Clear single stage is just as good as 2k clear and less toxic, less dangerous to use, and if you have a screw up you can STOP. With 2k you have a paint gun full of catalyzing clear that has to be used OR WASTED.I am an artist... I leave you with this sentiment... that you may all be artists in your own way.... and being an artist means you must find your own way...“A man who works with his hands is a laborer; a man who works with his hands and his brain is a craftsman; but a man who works with his hands and his brain and his heart is an artist.” Louis Nizer

I just wanted a light coat of clear to adhere firmly to bare aluminum (6061-T6) that I sanded to 2000 grit. I didn’t need a mirror finish, but a finish with some shine. I need protection from corrosion on the aluminum tubes and fittings for my ultralight glider… not from weather so much but from handling since it will be a fair weather machine. Researched for months and found this stuff… it is AWESOME! It’s light, goes on really nice and levels beautifully (it’s thin so spray light coats). I used their spray cans very effectively and it dries fairly quickly to touch ( about 2 hours) but cures up to 2 or 3 days. All the aviation folk said to use epoxy with a UV coat over it, or to use Cortec VpCl-373. Noooo way. This KBS diamond clear is so much better at adhering to bare metal! And frankly, I love the smell after it has dried over a day or so! Those complaining about the smell are way to sensitive… it is not bad at all and is only slightly smelly after it cures, but goes away over a few weeks unless you put your nose up to the metal. Not even an issue. This stuff is tuff flexible and glossy, even with a light coat or two. HIGHLY RECOMMEND!!!

Sent as a gift for buddy who does custom fishing lure painting. He liked it.

I used this clear for an automotive repair on my cars quarter panel and it was over a silver base coat. the paint was mixed to match and from an auto store in a spray can, I applied it on a dry 80 degree day in the shade as directed I used three medium coats at 15 minute intervals and allowed it to dry for about 1 hour. I then applied the diamond clear spray can as follows 1- single coat 1- double coat 1- double coat and 1- triple coat to gloss it without runs about 15 minutes between coats, there were no issues over the base coat. You need to watch the spray to be sure of overlapping the coats but otherwise it is like any other spray can paints. I used an automotive respirator with organic vapor filters as I was outdoors, I read somewhere this may contain some Isocyanates but, I am not certain and you need to be careful, It is advised you need a fresh air setup and not many people have that, also long clothing and gloves would not hurt but I'm not an expert. The clear was allowed to dry for a couple weeks and I sanded it with 1500 and it buffed easy over the silver color, the only issue I have so far is the clear has a yellow tint and it shows against the other panels and it stands out. I don't know how it will hold up or if it will yellow even further only time will tell? My take on the product is if you need to spray a stand alone item or something that does not need to have to be a perfect match you should be ok, I personally will not use it for any more for automotive work as you need a crystal clear for that! The best I have used so far in a spray can has been spray-max 2k and again it has the Isocyanates to deal with, maybe as time goes on they can improve this product to make it crystal clear as a 1k product? It is a decent clear with a longer shelf life, it was just not a good fit for my purpose and quite expensive, I hope this was of some help?

This works better than the liquid unless you got a sprayer

Good

This stuff is incredible. It is crystal clear. Had some scratches on my Cajun boat. Prepared surface and sprayed this diamond finish on and wow. Covered the scratches with high gloss, just what I wanted. I'll but more of this. It's very easy to work with!

I don’t recommend buying the spay can. I ended up repainting multiple times. A few notes:1. When the clear coat cures, it creates yellow color unevenly, and / or cloudy texture. I used this in a garage that’s about 50-60F.2. I figured the cause of this discoloration is due to:- Fragilely cured parts- Clear that got mixed with the base. I cured the base coat ~1 week.3. I sanded the yellow / cloudy area carefully but the hight of low quality parts is 100% unpredictable. “Just sand down” cannot fix the problem.I believe the product “can work” in a good environment and I suspect that’s why this has good reviews (vs just blatantly useless).This is why I review this spay can as “unreliable” that it requires too much to the user to get the best results.

Bought 4 of these to clear coat my old half ton truck. Did it with three cans with one to spare. Covers a large area and looks great when dried.

I liked it.

I was hoping this would coat my polished bronze clearly and smoothly. Removing this lumpy yellow goo was irritating

Application easy.

Diamond painting