Water-Proof Junction Box PFA130-E for Dome and Bullet Camera

The home we just purchased came with old small junction boxes. These new upgraded boxes fit the bill nicely. The fact this came with all the hardware and tether to hang the cover while installing was a big plus. This was the perfect size to fit my Lorex cameras in my home. The tether allowed me to hang the cover and camera (already mounted) to finish up tidying the ethernet cables in the box itself. Once that was done I simply placed the cover and my camera and tightened down the screws. This made install quicker and easier for me. I would recommend if you have Lorex cameras!

Needed a universal box so I didn't have to spend four times as much on a manufacturer box for the cables that didn't have attic access. It was big enough for a full sized dome, and I was able to drill my own holes in the faceplate. I threaded the holes with a spare screw, and cut the screws I used extra short so they wouldn't protrude into the cable underneath. The 3/4" threaded holes made it easy to use a 1/2" adapter and 1/2" waterproof cable fitting, and I angled the hole downward to prevent water ingress. I did have to remove the screws and tether wire for space. Of the three boxes I used, all are working well, but make sure you double check the tightness of the threaded caps before installing.

I used 4 of these to for outdoor Lorax fusion cameras. I was very impressed with the heavy metal durability, compared to a previous plastic one I ended up returning. This box came with all the screws, hex tool and a set of basic anchors to make for a secure installation, however, you may need other anchors, depending on your install.i was alo impress with the metal hinges and cable, allowing you to:1. Mount the box first2. Remove the lid, and mount the camera to it, then3. Attach the lid to the box and screw in.This really is a quality box.The gaskets are on ALL included screws and covers, eliminating the worry of moisture entering the box and ruining your connection. The 3 holes on the cover lined up perfectly for my cameras. The box is a 3 hole mount, although you may only need 1-2 good holes with good screws.Be sure to mount the box at the correct spots for your particular camera field of view BEFORE you mount your camera. I had to re-drill a few holes in stucco once to achieve my desired camera angle.

This junction box is really poorly made and looks cheap. The design is way off and it takes a lot of effort just to close the box properly.

Writing a review that I wish someone else had already. This junction DOES fit the Amcrest IP4M-T1044 (dual lens dome) without any modification. I have not installed it yet. However, a preliminary test fit went smoothly and I feel like this will work well for my outdoor camera. There are orings/gaskets on the exterior screws in addition to a main gasket and seal on the housing. This should stay water tight for the life of the gaskets. Also, it includes the screws to attach the camera to the box (important as the holes are threaded for machine screws and most cameras come with wood screws). I'll update after I've installed it.Update: I installed the camera and junction box the other day. It's a right fit for all the wiring on my specific camera but I got it all crammed in. I think I will end up going back and wrapping all the use and unused connections in silicone tape as well as running a bead of caulk around the edge. It seems like it will be ok without all that but better to be safe than sorry.

Seems to be built pretty well. The screws provided have rubber gaskets to prevent water from entering. The top has plenty of holes to accommodate different mount arrangements. The screw holes for mounting cameras are not drilled completely through the top so it remains water-tight. Mounting hardware included.

This is a quality metal box that can work as a junction box or a table stand for bullet cameras with 3-hole bases (which would tip over if you tried to sit them on a table without an additional base). Just make sure it fits your camera. I have a variety of brands and it does fit my Reolink RLC-510WA bullet cam - but it does not fit my Eufy E330 bullet cam.

Works great.