Westinghouse Ceiling Fans 78158 Turbo Swirl One 76 cm Six Indoor Ceiling Fan, Opal Frosted Glass, wood, Titanium Finish with Light Maple Blades

The fan is well made, seems very durable, and easy to construct and fit. The hardest part was getting a good fixing, I had to go into the loft, dig around the awful insulation, and add some timber support, to give something solid to screw into. I didn't use the supplied fixings for the bracket, instead opting for some hefty 5x70mm wood screws for peace of mind. I wanted to use an existing wired wall switch for the light and was able to separate the live wires for the light and fan, and use a wago to connect the light to the light switch. (Using a multimeter to work out which wire was which.) We initially installed without the rod due to relatively low ceilings, but the fan performance was poor and the AC hum transferred into the joist, so it was a little noisy the first night (but we had no problems sleeping.) Next day I installed the rod, fan performance was dramatically better, and quieter too, as the rod hangs from the bracket rather than being directly attached. One minor issue was some initial rattling, but adjusting some screws on the lower base of the unit got rid of this. Installing the rod may also have helped with this and we've not had any problems since.

We installed the Westinghouse fan & light pendant just today so, for now, our review will focus on the installation we did rather than how it works out long term. I will say from the outset that I can see it operating just fine for quite a while. It seems solid and gives off an air of competence in its manufacture, but only use will determine the facts of that aspect. I'll look at 1/ Things that came up during installation (inc. remote unit) 2/ How it looks and works as a new unit 3/ A few observations 4/ Definitive info about a suitable bulb Short-form review. 1/ It can be a real fiddle to install if your wiring isn't perfect. 2/ Looks nice, fairly quiet, some nice features. It blends. 3/ Needs work if you want to carry on using your existing simple wall switch. 4/ You can angle the bulb holder to get a choice of bulbs to fit. Just don't do it too often. But first, please remember this if you plan to fit this yourself and you're not an electrician. Dying to fit your fan? Installation could be short and painful if you don't switch off the lights circuit at the consumer unit/fuse box. The light switch alone is not enough, since the lighting circuit in the ceiling is always live, and the wire to your lightswitch just makes interrupting the circuit for that particular room's light easier - the wires for the rest of the lights remain active (otherwise switching off one light would switch off every other light in the house!). So kill the lights circuit at the consumer unit with its switch, or pull the appropriate fuse. 1/ Installation I'd like to say that it is a "breeze", but despite the bad pun, it isn't. I had a terrible time with the ceiling wiring because the instructions assume that you will only switch the fan using a remote control and not from your old wall switch. They also assume your ceiling wiring will be neat. Ha! If you simply can't live without it being wall switchable using your old fitting, you will need to split out some of the wiring at the ceiling rose to make that separate switchable circuit. In my case, I was pretty irritated about this assumption on the part of Westinghouse and will get an electrician to get that working as we'd like. The online versions of the specs and installation guides don't mention this problem because the instructions expect you to do things Westinghouse's way, and not necessarily how you'd prefer it to work! That niggle aside, we did manage to get it working along with the wireless remote we'd also ordered first time, no problem. Installation was still a "monumental faff", even so. Most of the work needs to be done up at the ceiling and, if you are fitting the optional wireless remote as we did, you have twice as much to do. First of all, though, you must have somewhere very solid to mount the fan, either a concrete ceiling (in which case I advise getting better, longer, screws for the unit, and suitable fixing points for the concrete) or find the central line of a ceiling joist. If you have a drywall ceiling I don't see a heavy unit like this staying up there for longer than a week unless it is attached through to a joist. If the people that built your house were even halfway competent, the ceiling wiring should come down adjacent to a joist. Westinghouse organise their own cabling quite nicely, with snap-together cable connectors complete with alignment arrows for orientation (between fan and remote), but if your ceiling cables are short and plentiful, connecting to the mains can be a pain. With a light in the middle of a typical ring circuit you'll have nine wires from the ceiling, 3x earth/live/neutral, and a fiddly little chock-block to push the copper into. The chock-block is also a little deeper than most I've ever used, so if the stripped parts of your wires are in any way short, you might want to ensure that there is enough copper beyond the shielding before you try pushing them all into place and screwing them in. Things can get a bit tight and, for laughs, Westinghouse instructions just show single cables going into the chock-block! If you're installing the wireless remote, the next paragraph covers this, otherwise you can skip it. Installing the optional remote receiver (the part that goes inside the ceiling rose) ought to be easy, but in our case the bundle of wires exiting the ceiling was slightly obscuring the slot in the ceiling mount into which the remote receiver is pushed, so in our case it was a pain trying to get it past the bunch of cables, and because wires emerge from the unit on each side, it only pushes through one way. My advice would be to put the ceiling attachment in such a position that the wiring emerging from the ceiling comes up *beside* the mounting bracket and is positioned right next to the chock-block, and not through the hole in the centre of the ceiling bracket, and also to one side of the gap in the bracket into which the remote receiver is slotted. The large Westinghouse ceiling rose will be large enough to accomodate this. Some people have mentioned that it is a nuisance fitting the blades, especially fitting them last! Well, yes and no - there is a slot in the lowest section of the fan that allows a screwdriver to pass through to the fan disk (which isn't the bit with the light on it, but the bit above that), so provided you have a magnetic screwdriver that can hold the screw to itself while you feed it through the lowest section, you'll be okay. These screws are already in the fan disk and need to be removed, and then screwed back in when the blade has been positioned properly. With 2 screws per blade, this makes a fair bit of time working over your head. The blades have metal attachments that use the 2 screws mentioned to attach to the fan disk, and three more decorative screws per blade with very tight felt washers. These can take a while to prepare (threading washers onto the screws) so a willing helper can take that job on! 2/ How it looks and works In situ, the completed fan looks great, with a contemporary look that is very easy on the eye. For something considerably larger than most ceiling shades, it does a great job of disappearing once you get used to it. It is very quiet in operation, although with my good hearing I can clearly tell whether it is running even with my eyes closed, even on the lowest setting. That said, it is an unobtrusive hum that could actually help people that are woken by the slightest noise because it raises the background noise a little and might hide a few of the quieter sounds. On the high speed setting the blade/wind noise is more than the motor noise - there is a distinct "rush" of air with the motor almost buried beneath it. It is still not overbearing, and may even help people drift off to sleep. If the unit is not mounted completely immobile, you may find that small imbalances in its rotation can set up rhythmic creaks. Ours does this a little on high speed, but we can live with this because the high setting would be very seldom used. Even the mid setting is rather breezy. The switchable direction for the fan is a stroke of genius for winter use, when heat gathers up at the ceiling and needs to be encouraged to circulate a little more. 3/ Observations If your remote doesn't seem to operate the light but runs the fan just fine, try switching on the light using the pull cord, after which you can use the remote for dimming. It is a bit of a bind that we can't carry on using our wall switch (until we get out an electrician to split the wiring and make it work that way), and I was a bit surprised that the lighting remote button didn't work until I'd pulled the lighting cord. It seems to need to be switched on by both the cord and the remote together. The bulb we fitted would also only be switched entirely off by the pull cord. Using the dimmer, the bulb (a LED dimmable one) would go to a minimum brightness and just carry on glowing if switched off, and dimming similarly went from bright to this muted glow, so for now we will need to use the pullcord until we figure this one out. Some dimmable devices have a "minimum brightness" setting that can be adjusted, but I'm pretty sure that this unit doesn't have that very handy feature. 4/ Compatible bulb sizes. Some reviewers also complain that it is hard to find bulbs that are small enough. I've just installed a Diall E14 bulb bought from B&Q, which is 107mm end-to-end. This is possible because the glass shade has a wide point after which it narrows down into its inverted dome, and by angling the light bracket that holds the bulb so that it is inclined slightly down-angled from the ceiling, the tip of the bulb will fit into the shade at its widest point. Going anywhere beyond 107mm would be pushing your luck, though. It is a tight fit. We will look for an E14 bulb that is shorter and fatter next time, and will also see whether all LED bulbs have this problem of not switching entirely off on the Westinghouse dimmer remote. (See updates below) Sorry if this is all rather long-winded for you, but the laughable Westinghouse instructions really almost require consumers to fill in all the missing bits, and the tips & tricks. I will come back to this review after a summer of use and mention how we got along with it (gotta use these calendar apps for *something* useful!). Until then, stay safe. 4/4/17 After two weeks of use the fan is now settled in. Initially it would cause creaking sounds from the ceiling on top speed. It no longer does that. Another aspect we noticed the first time we ran the fan together with the light is that there is light spillage up to the ceiling, and this causes shadows of the fan blades to flicker on the ceiling (the fan is on the short extension tube, not flush-mounted). While we were okay with this, we thought it should be mentioned since the subtle strobing effect could disturb some people who are sensitive to flickering light. 18/4/17 Last update for a while. We ended up switching the LED bulb to a halogen one. Although the LED E14 bulb worked "okay", the only way to stop it glowing was to switch it off using the pull-cord on the ceiling unit. Couldn't be done from the remote, it would just go to a pale glow due to the efficiency of LED technology, which can produce viable light from the very tiny amount of current from a lighting circuit that is switched off! This was proving to be annoying, so we switched to halogen and the dimmer (remote) works a treat now. With the LED bulb, minimal settings were still putting out a lot of light, and switching off would still have the bulb glowing. With halogen, "off is off", and if we use the on/off button on the remote it comes back on at full brightness. If we switch back on using the dimmer button, it comes back at the last dimmer setting. Really nice to use. On the plus side, if you can live with the LED quirks, dimming the LED doesn't result in it flickering (we used a Diall E14 candle LED bulb from B&Q - we switched to Diall halogen at 107mm long end-to-end. Edit 2-Sept-2017: Still loving this unit, which has seen us through a few sultry summer days in quite a lot of comfort, even if it has sometimes meant interrupting things and going to the fan for a cool-down and a rest. We may need at least one more, maybe two, for other rooms. We thought we'd never have need of the most forceful setting but have used it now and then when we've woken feeling too warm - it knocks the heat back really well. Most summer nights we've left it on setting 1 and had a very comfortable time. It might actually be too effective to use in winter, when we like to move air around to keep the room feeling fresh. In the months we've used it I can't say I've ever forgotten that it is there, which I thought I'd probably do. It's very unobtrusive but still a bit of a presence in a low-ceilinged space (our ceiling is about 7ft 6in/228cm from the floor). The only possible gotcha with these units is the risk of inadvertently putting fingers or arms up into the fan disk. This might sound a bit suicidal - you might wonder why someone would do this. Just try pulling on a t-shirt nearby - it can be that easy to get your hands awful close to the fan disk just by doing something else that you do without thinking. If there's a risk like this, you might need to consider mounting the fan over something else that stops you standing anywhere near or beneath the fan. In our room the fan disk is about 6 inches in from the foot of the bed, which is also wide enough to keep us away from the blades from either side too, so we're okay. I've had a couple of close shaves though, so this is something that definitely must be borne in mind. It either needs to be mounted high enough to be out of reach of outstretched fingers, or sited so that you have advance notice that you're getting rather close to the blades. It's too easy to forget the fan when you're doing something familiar such as pulling on a shirt. Apart from that caveat we're still loving it. July 2021 - Heatwave. This fan has been wonderful during the heat warnings in the Southwest this year, and we're now very used to it. I've occasionally awoken with dryish eyes due to the breezes overnight, but this can be fixed either by using the winter setting (where it runs in reverse to push the warmer air at the ceiling down around the walls and onto you!) or arranging to sleep in a position that avoids you facing the breeze. During exceptional heat it's been a real pleasure to have had a damp flannel to hand, and dabbing on some water on face, shoulders, arms. The cooling doesn't last forever, but it does help to get skin temperatures down quickly. May 2024 - automation! With the arrival of a bit of light home automation we now switch and dim the ceiling light using voice commands. There is now also a greater choice of compact bulbs on the market, including small more spherical ones that fit more comfortably inside the glass diffuser/shade. You would still need a remote for the fan if you didn't want to use the pull-cord on the fan itself. It's safe to say that we've never once regretted installing this fan, and if the climate carries on as it is, we may install others in other rooms.

After a couple of problems with ordering this the fan arrived this morning and is now in place and working. Unfortunately the Westinghouse RF Remote which I had ordered with the fan did not work so I am now waiting for a replacement remote. The fan itself is a very neat unit, well suited to the small double bedroom where it is installed. There is a bit of mains hum in evidence whilst the fan is on, this is independent of the fan speed setting and the installation instructions say this should disappear after a 24hr running in. There are no rattles or noises other than that. Installation was simple once a suitable joist had been located and wires from the previous ceiling rose were drawn through. The installation manual is multilingual so there is a lot of flicking backwards and forwards. It pays to read it through before you start though. I decided to fit the blade mounting brackets to the main assembly before attaching the unit to the ceiling as this seemed more sensible than working upside down at a later stage. I followed the example of a previous reviewer in adapting a 5w led candle to fit the small screw light fitting; this doesn't give enough illumination for a primary light source in the room but no doubt purchasers will make their own decisions on lighting options. In a bedroom where the light is not on for long periods a led bulb is only going to give a modest saving in monetary terms and, assuming that I get a working remote, which has a built in dimmer, I may well opt for a halogen bulb. Later- Amazon replace the faulty remote and this is now installed and working. As anticipated, the light dimmer control is not suited to led lamps. On the plus side, the fan control electronics seem to reduce the operating hum quite significantly. I also added some noise absorbing pads on top of the mounting plate and thick rubber washers under the mounting screws so the fan is now virtually silent apart from the actual airflow.Had this been achievable on the initial installation, I would have given 5 stars.

Purchased this fan after much searching and for its good reviews. Very good quality fan and quite heavy, bought for our pointed ceiling caravan. Had it professionally fitted by electrician. Opted for flush fit to ceiling as limited head room. Although fan looked fabulous, good light and perfectly fitted in with our decor, there was hardly no air flow and the fan was very noisy on the higher speeds. We were very disappointed thinking we had made a bad decision on purchase. However, we were wrong. The electrician suggested he fit the extension rod as perhaps there was not enough air flow above the fan to make it work. This he did, and wow what a difference. Even on speed 1 the air flow is good, but on speeds 2 & 3 the air flow is excellent. Also it has eradicated the noise. All in all, we are absolutely thrilled with the fan. My only advice is fit it with the extension rod. We were pleased we went for professional fitting as we are not so good at DIY. Also it does take 2 people to fit it (my husband helped the electrician). My only query now is that the fan wobbles when on high speeds. I have asked the Amazon community a question just to see if this is normal, although it would not put me off purchasing this fan.

Great product, have fitted 4 so far. Pre-build blades on motor and wiring through shaft then sit on box supplied in, makes installation easier, just hook on and connect. Fix to beams in ceiling as they are heavy if possible. Wiring is simple

I bought 2 of these fans and installed them in 2 south facing bedrooms. During the warm weather I tested them and the product quality is markedly different. One functions beautifully and emits a 32db noise level which is acceptable. The other has a very noisy motor (57db) and it "hunts" to maintain a constant rpm. I complained about the PERFORMANCE TO Westinghouse and they wanted video and sound files before dropping all interest and telling me to return via the retailer! HOW CAN THIS BE DONE WHEN THERE IS A 30 DAY RETURNS WINDOW, NO PACKAGING AND NO INTEREST in Customer Service from the Manufacturer???? Let battle commence to get a fan that works according to acceptable parameters preferably before winter!

Thos is the second Wesringhouse fan I have bought.The first is almost 14 years old and only now showing signs of fatigue. This new one is a quantum leap in its appearance over the original and looks absolutely superb in place. It operates in near silence with only the sound of the air audible. The bracketry supplied to attach it to the ceiling has an ingenious plug that allows installation without the weight of the fan hampering your efforts and the unit can be flush mounted or lowered depending on your own requirements. The maximum wattage for an incandescent bulb is 60 so we have paired it with an LED e14 bulb to maximise light and still only use 9 watts. So if you are looking for quality, reliability and good looks then you wont go wrong with a Westinghouse fan.

Well made, fairly easy to assemble as long as you are ok on a step-ladder, it's not a light weight but manageable. Wiring is ok if you have enough mains cable to pull through once the ceiling rose is removed. If not you'll need to use a connector block to extend the cable to the fan and reconnect the on-going circuit and the wall switch. (This is all assuming you are replacing an existing pendant light). With the fan running it can be liable to wobble slightly if it's only held in place with the supplied bracket. It is still safe in that it's not going to fall on your head, however, I sorted this easily by adding a third small bracket on the outside of the fan casing and the ceiling 45 degrees around from the existing fixings. This stopped any wobble and made the whole thing quieter too. There are two pull cords, one for the light and the other for the fan and speed. A side switch controls fan direction. Could you sleep with the fan running? Well, I can, but then I can sleep through a disco giving it welly. All depends on how light a sleeper you are, obvious really. The fan is quiet, but not silent, it works very well and I love it. I hope my installation comments don't put you off, better to get a sparky to fit it if you are unsure, and have the use of this good value for money bit of kit. It's almost a breeze :)