Blue PU Pneumatic Tubing Air Hose, 6mm OD x 4mm ID, 32.8ft

This product arrived boxed with the following content: 1x roll of 39.4" blue ¼" O.D. tubing 2x of each of the quick lock fittings 1/4" O.D. Y 3-way connector T 3-way connector Elbow Connector Straight Connector 2x ¼" O.D. quick lock to 1/8" NPT thread male 4x ¼" O.D. quick lock to 1/4" NPT thread male 1x short roll of Telflon tape ½" or 12.67 mm wide 1x Black Tube Cutter with triangle blade and round groove in back for removing/uninstalling tubing from fitting Everything can as described. And the tubing was easy to cut and install. The fittings, tubing, and the included cutter all worked great together. I have no air or water leaks from using this set. The tubing was the correct size and fit the fittings very well. The blue ¼" O.D. tubing is flexible and sturdy. The trick to these fitting is to push them all the way in then tug back a bit to lift the collar to lock and seal. If the collar around the tubing stays down or tubing itself not seated all the way, this could cause leaks. On another note, the Cutter Triangle Tube Blade is removable. It's replaceable but the replacements are not cheap. Perhaps, the blade could be re-sharpened once it's dull. This kit provide great value for the cost and work flawlessly. I've gladly recommend.

Ran this polyurethane tubing throughout my pickup truck to feed air fittings and an air horn and after putting it through everything a truck environment throws at it — heat cycles, vibration, routing around tight bends and sharp edges — this stuff just keeps performing like it was installed yesterday. The 8mm OD with 5mm ID is the sweet spot for pneumatic accessories on a vehicle build. Enough flow capacity to feed an air horn without the pressure drop that ruins the dramatic effect, and flexible enough to route through the tight spaces a truck firewall and engine bay love to throw at you. Because nothing says "fun install" like trying to snake tubing through a factory grommet at an angle that defies geometry. Polyurethane construction is the right material choice over standard vinyl or rubber for a vehicle application. Handles temperature extremes without getting brittle in cold weather or turning into a wet noodle in a hot engine bay — both of which are real problems with cheaper tubing that ends up cracking or kinking after a season. This stuff bends where you need it to bend and stays put where you route it. Push to connect fittings seat on the 8mm OD cleanly without any leakdown under pressure. Ran the air horn through a full test cycle and pressure holds solid with zero weeping at any connection point. Quality is consistent throughout the entire length — no thin spots, no surface defects, no concerns about a weak section failing somewhere inconvenient. For truck air system builds, onboard air setups, or any vehicle pneumatic application, this tubing is the right call. Highly recommended and my air horn agrees.

Nice air kit

Very good

Great product. Used for repair of water line on refrigerator. Complete kit with cutting tool ,various fittings and tube. Priced well versus buying all items separately

Had to replace the airline in my plasma cutter and this worked great.

This kit is great and enabled me to replace the compressed air line on my Marshalltown Enforcer texture sprayer at an affordable price. Marshalltown does not sell the blue polyurethane air line separately but bundles (as spare part # 10406) it with the mud hose, which I did not need, not to mention that "spare part" costs about $70 (not including shipping costs and applicable sales tax). Note: On the back of the box it states "Do Not Use for Drinking Water system" (for example the water line on a refrigerator). This tubing is made of Polyurethane and is NOT safe for potable water.

Fittings worked well for me and the tubing fixed my air leaks, the tubing cutter is a bonus

Produit de qualité selon mon utilisation domestique. De plus, ce tube viens avec un coupe tube ce qui est très pratique.

bueno

Super easy and quick to install Very clean job Just make sure you push the hose completely in and you are all set Super satisfied

The pipe is not as described, I use it for ARB compressor which has only 150 psi pressure and it burst all the time

Es muy útil al incluir los conectores.