Vehicle Awning, 4.6ft x 8.2ft, Rooftop Pullout Ripstop UPF50+ Side Awning, Reinforced Hinges & Poles for Jeep/SUV/Truck/Van

This awning is very well made and is very durable. Setting up and closing up the awning is simple and easy enough to operate by one person. The poles are durable and easily support the awning. The fabric seems durable as well. The size provides plenty of protection from the sun and the elements. The case for the awning is also well made.Mounting the awning on my rack took a some additional parts. I purchased some electrical pipe clamps and some unistrut which gave me something to bolt the awnings L angles to. Parts were inexpensive and easy to install.Overall this awning is well made, easy to use and a great value.

I bought this awning basically for shade on the beaches when I go fishing down in Hatteras. I’ve got the 8x10, and IMHO going large is better, at least for me. I would have bought the 270° unit, but didn’t want to spend the money. I’m sure at some point in the future I wish I had. In any event, this unit is very well made.I’ve read many reviews which complained about the bolts, not being right, SAMOUT not being responsive, cheap fabric, weak/undersized, poles, etc. Be advised, NONE of these reviews are accurate. I would dare say it’s not only untrue, but total disinformation; and I wouldn’t doubt they were paid or were provided by competitors. Let me assure you. That the bolts are a 270 stainless steel. The mounting brackets are heavy duty and powder coated. The poles appear to be engineered with the factor of safety, i.e. they’re more than satisfactory. The fabric is quite thick, is internally reinforced and if used properly with slope, I see no reason why it will not shed rain.I don’t know about you folks, but I’m so sick and tired of reading reviews which Trash a product for no reason. I can assure you that I looked at them all and made the decision to go with Samout over the competition for not using plastic in the corner clips, which is where all the stress is going to be.To mount this onto my truck cap, I have Yakima mounts with round Yakima bars. To connect to the bars, I purchased on Amazon round pipe connectors that are typically used to mount lights on top of a truck. These I placed on either side of the rack support as depicted in the picture. I elected to mount on the underside of my bars by turning the L bracket facing down. I did have to go and buy four 5/16” x 1 1/4” SS bolts, nuts and washers at the big box store because I didn’t want to utilize the long bolts nor did I want to cut them off. If you have a rooftop basket, they have short little pieces that mount horizontally on top of the basket and the brackets Mount below the basket. FYI. Installation took me about a half hour. The hardest part was fitting the sliding bolts into the bracket. On that I had to help of another person. Everything else I did solo.Now that I have the unit mounted, I wanted to see how hard it would be to set up by myself. Once you unzip the bag, the first thing you do is r the three retaining straps, unroll the unit about a foot and flip it over above and out of the way. Then you can reach in and grab the horizontal bars and pull them out past 90° so that you can unroll the shade without difficulty. Once the Shade is fully unrolled, I dropped both legs and extended them to about 6 feet tall and had them leaning away from the vehicle. Then I extended the horizontal sides, one at a time and attached them to the corner brackets and attached the side Velcro pieces. I didn’t bother staking the unit down, because I was just opening everything up to make sure nothing was missing or broken, and everything was fine. When I was through looking at it and taking the above picture, I disconnected the Velcro, disconnected the side members one at a time by pulling the pens out of the corner, brackets, and push them out past 90°. Then as I held the outside edge, I replaced the vertical SUPPORT legs back into their place and started rolling it up. You have to take care enrolling so that it rolls evenly all the way up, otherwise you may have a problem fitting the end into the bag. Once I got it close to the bag, I flipped it up over the rack, put the side members back into their respective slots, and re-strapped it starting at the center then zip it back up. it was that simple, I did have to roll it back out because I had rolled it up unevenly. And even with all that, it only took me about five minutes to set up and about five minutes to take down. It definitely would’ve been easier with two people, but it was easy enough for a man in his late 60s to do alone.I did contact the manufacture to find out if there was any concern of how far away from the attachment point (which in my case was at the horizontal bars) you could cantilever the unit away from the attachment. I did this because there was no information in the instructions. Samout responded to my email in less than 24 hours, so anybody that says the manufacture doesn’t get back to you is mistaken.If you’re like me and plan on using this at the beach, you may want to purchase some sand screws like the screws you use to hold a dog to its chain. I plan on using a couple of 5 gallon buckets filled with sand and attach the ropes accordingly. If I remember, I will come back on here at the end of the summer and provide a review after full use. Hope this helps.

While my expectations were not set very high being a prime day deal, I was very pleasantly surprised with the build quality. I needed a replacement for the awning on my van. The original one from 25ish years ago, broke the gear mechanism to wind it out. Due to age repairing was not possible. Similar awnings required a leg support being attached at the bottom of the van for support. I did not want to drill new holes for supports. It did take some pretty significant modification using pieces from the old awning to give a surface to bolt the new awning to. Once the surface was created, it was very easy to install. It's rather lightweight and I'm worried about it's strength in the wind. I use the van to tailgate at football games in the fall/winter and I may not be able to use it on days with not so great weather. It also definitely takes 2 people to set up and take down. The smaller sizes you might be able to do by yourself though. It is very easy to setup though. I was hoping to not have to use guy lines just cause of the hazard, but I don't think it's heavy enough to stay in place.Overall, I think it was a great value but it took 2 months to get delivered. Easy to install and setup. Seems pretty sturdy but lightweight and uses Velcro to secure the fabric. I would have given it 5 stars if delivery was faster and there was more pictures in add showing how it's mounted.

This awning works fantastic for such a great price! I honestly was fully prepared for it to be reasonably decent if annoying, but I used it nearly every day on my beach vacation. You just unzip the bag, unroll the awning, unfold and extend the legs, unfold and extend the horizontal bars and slot them in place, then there's Velcro to tie the awning edges to the horizontal bars and tent line and rent stakes for tie downs. It holds up amazingly well, was a great shade, and I was able to regularly set it up and take it down by myself.It'll mount to any roof rack, but the directions do want you to drill holes in your roof bars to then bolt the L brackets onto that hold the awning to the vehicle. I didn't really want to do that, so I actually used heavy duty zip ties (4 per bracket, each zip rated for 75lbs). I would recommend getting some basic hardware and simply making some clamps to attach the brackets to the car.

Finally had the awning attached to my rooftop basket. I ordered special brackets from a company called Anderson Design and Fabrication so I didn't have to drill into my roof top rack, etc. The brackets work brilliantly and allowed installation in less than 20 minutes.