CyberPower BR700ELCD-UK BRICs Series, 700VA/420W, 6 UK Outlets (3 Surge only + 3 with UPS and Surge), 1 USB Charging Port, AVR, Brick Format

I purchased the CYBERPOWER BR700ELCD-UK Line-Interactive UPS 700VA/420W, its is quite heavy, the lead acid battery will be most of the weight, the unit came with about 70% charge in the battery and after my initial testing the unit did have to run over night to be fully charged, yes on testing (switching power off at socket) the unit switched over to battery with no adverse affects to my PC. My own problem is the electrical power coming into my home goes off for 2 or 3 seconds and comes back on and could damage my PC in many ways. My set up is to protect my graphics design PC and 43 inch monitor, running at Idle consumes 80w and has a maximum load of around 200w from the wall socket, the Cyberpower unit takes under 3w to run when fully charged (2.4w in my case ), when the power has failed the Cyberpower unit sounds a two beep first alarm every 30 seconds or so and when the battery power is very low sounds a constant beep beep beep beep second alarm, with a constant 80w load (PC at Idle) my run time on battery is over 22 minuets between the first and second alarm and I still have time to shut down the PC beyond the sounding of the second alarm, when running on mains power the LCD panel on the Cyberpower unit indicates with my 80w power consumption my run time on battery will be 34 minuets but as with all electrical devices you have losses as indicated above with my real time testing. I am very happy with the Cyberpower unit and to have purchased one of the higher power units would have been a waste of money as 22 minuets will allow me to save my work and shut down the PC. 2.4watts at 29p/Kwh = £6.10 per year, small price to pay for safety backup device.

I liked the fact that I didn't have to sit for hours figuring out how to operate it. The device has features that I can and will explore in due course but I just plugged in and that was it. There is no noise, I feel it from time to time and it doesn't seem to generate any heat. This is a big safety plus. It has options for smart app, Internet etc I haven't looked into yet. The price is great for this solid device. Looking at it makes me feel I can trust it! I intend to buy another one soon for other devices in my home.

In common with most UPSs listed here, the runtime on battery isn't stated in the item description. I bought the smallest (420W) of these devices and at full power I'd expect 5 or 6 minutes of runtime. Enough for an immediate clean shutdown but not much else. As it happens, I bought this to protect my broadband and some other small items (smarthome hubs and a couple of raspberry Pis) so I'm mostly running at about 10% capacity and would therefore expect this to power everything for maybe 50 minutes. Long enough to keep going through the average power cut. Aside from battery capacity this seems like a decent unit. Plug it in, plug equipment into it, and off you go. The USB interface connects nicely to a Windows machine and the software lets you perform a clean shutdown when the power goes off. I actually have mine connected to a Pi Zero running Network UPS Tools, with the monitoring data fed into Home assistant. NUT lets you schedule shutdowns as you need, if you don't mind Linux-level config file hacking, and home assistant provides nice monitoring of power consumption and estimated runtime on battery. Overall I like this unit. There aren't many cheaper devices and there are a lot of more expensive devices, so this seems like good value for money to me. I've only had it for a few weeks so can't yet comment on long term reliability.

I bought this to provide backup power for a Synology DS923+ and my router. Took less than 10 minutes to plugin and setup. The Synology immediately identified the UPS. I simulated a power failure and the unit will provide 74 minutes of backup although I have set it to shutdown after 10 minutes. It’s very well built with a useful display to provide metrics.

Style Name: 700VA/420W Decided to buy UPS after recent experience of a power “brown-out” where the power fluctuated enough to cause devices to power up/down multiple times – not good for NAS (Network Access Storage) devices. I decided not to “sell myself up” with regard to power spec and try the lowest power output that would comfortably meet the needs of a clean shut-down for my NAS, hence 700VA version. Brick comes with a type-B USB cable for connection to a NAS. This enables the NAS to monitor the state of the UPS and determine if/when to start setting disks to standby. In my case I have a Synology DS212J NAS (quite old tech) but it recognises the UPS when connected and you can customise a delay time before placing the disks of the NAS in offline/standby mode. There are three sockets in each of two banks. One bank is Battery Backup+Surge Protection, the other Surge Protection only. It also provides a USB power output port and RJ45/RJ11 sockets in between the mains socket banks. I keep the protective packing film attached to stop dust entering these since the “brick” faces upwards in my installation. Although the brick has keyhole slots cut in the base for screws mounting vertically on a wall, I feel it might be safer (because of its weight) sitting on its feet in the horizontal position. I found the actual mains sockets quite stiff for inserting UK plugs, but since plugs will seldom be removed/inserted this is a minor criticism. Brief instructions were included on the box and a leaflet inside. Once the unit is switched on there is a second button to allow scrolling through the settings shown on an LCD display. The display cycles through power input Volts, power output Volts, charge remaining etc. Testing is simple once everything is connected. Switching off the mains supply to the unit, connected devices should continue to run undisturbed. A double beep sounds at intervals alerting that the mains power is cut and the unit is operating in backup battery power mode. Online advice seems to recommend not discharging the batteries too much. So the UPS is more suitable for allowing clean shutdowns than enabling continued use of devices during a power cut. If the latter is required a larger UPS would be needed. I feel a lot happier about protecting my backup data now in the event of any future power interruptions. “Fit and forget” tech once it is setup. Pleased with my purchase.

Bought this in the lowest rating option to power a NAS to protect it from outages and surges. Obviously the importance of units of this sort are more obvious over the longer term, 3 months tells you very little. But it appears to be well made and the display is a nice touch not seen on the lower spec APC units. All indications are it will run my 2 disk Synology DS223J for about 2 hours before shutting down. More than enough, I just need to avoid a hard shutdown if the power goes off. Only down side was that the mains lead is hardwired into the unit so placing it in a cupboard means cutting plug size hole in the back, why not a detachable kettle lead connection or Figure 8? In the end I chopped off the plug and fitted a C14 female kettle plug on the end (Amazon £3.50). Not ideal but at least it was a much smaller hole that was needed. Besides I had several spare kettle leads of various lengths so avoided using an extension lead. Cyberpower please consider this change, it would also make your unit compatible across different electrical outlet styles, just by changing the lead.

We live out in the country where power cuts are common, and we've just moved to internet phones. It takes our modem and router several minutes to recover from even the briefest power cut, and it was getting annoying - especially when we realised that we were without a phone, too. We bought this UPS - rated at about 10 x the total power draw of the equipment we intended to run through it - and just plugged everything in. Instant peace of mind! With phone, fibre box, router and phone adapter 'covered', we have about an hour to react to mains cuts - and they usually last for less than 10 minutes, except in dire emergencies. We can do without TV and Sky box (adding them would need a more powerful UPS) and they restart easily anyway. Job done!

Charged to 100% as per instructions. Downloaded s/w and connected up to laptop via USB cable. Waited for an hour or so as I was busy and then installed the software. No connection found which is correct as I'd not switched the UPS on yet. While NOT plugged into the mains, I switched the UPS on and the GUI for the power management s.w connected and reported 85% capacity left. So it had lost 15% switched off. That just can't be right!!. If I can't contact the seller, I'll need to return it as either defective battery or defective design. I appreciate the UPS itself puts a load on the battery while on but when only powering itself, it can not be right to show 85% When mains was applied, it went back to 90% so by any measure, 10% had gone in one hour while switched off. Thats a lot of power!!! I'll update later if I get sense from anybody.

Works a treat