ZB-L100K Handheld LCR Test Clip Universal Digital Bridge Kelvin Test Line SMD Chip use for DE-5000 LCR Meter

Well made item. The clips are sturdy and firm when clamped on component. The plug fits firm and secure. Easy to use without cable issues. Great value for the money.

I found it to be well made, true Kelvin clips. The part that plugs into the LCR meter has two sides to each tong that are insulated in the middle of each tong, and appropriately wired to the clips. Works perfectly with my ZOYI ZT-DQ02 so indeed will also work with the ZT-DQ01. I can easily recommend this product 👍

Nice. Great addition to my Electronics Laboratory Bench.

I'm giving this four stars ONLY because it doesn't have the exact size or retention features the Hantek 1832/33 meter wants. But it does fit the slots, and with some rubber retention cords, it will remain seated. This is the first time I ever used Kelvin clips. My primary use is in building RF circuits, where guessing component values will not work. To use these clips successfully on the Hantek (and probably other meters as well), it's first necessary to calibrate 'open' and 'shorted' clip conditions. I was very pleased with the stability of readings (for days) and being able to get sufficient accuracy even on low picoFarad capacitors and low microHenry inductors. The readings were hardly affected by re-positioning the clips. I might wish the leads were longer, but am aware there's a fundamental trade-off between length and stability.

Excellent add on to RLC meter

Buy it you will not be disappointed very accurate.

I've order these in July 2025. I have an East Tester 433 and Keysight U1733C handheld LCR meters. I tested them using the preset test frequencies of 100/120/1K/10K/100K on both meters. It did not give correct values at 100KHz. Nowhere close. Even after doing opens/shorts correction/calibration/compensation. The ET433 also has a preset frequency at 40KHz and that was OK. Since my projects are audio related, the 100KHz thing was not important to me. But three days ago, the leads stopped working. They pass the opens correction, but not the shorts correction. So I purchased a similar set of leads from Amazon from a place called BOCEUC. They look like the same product, but it works at all frequencies correctly.

As shown in my photos, the 3 flat PCB-connections that insert into your DE-5000 are too thick by 0.14mm, and they have no taper at the tip, which can make it impossible to insert without damaging the metal parts inside your DE-5000. The overall shape is larger and inferior to the DE-5000's included Tweezer accessory as shown in my photo. And even if you sandpaper down the PCB tips so they are tapered, you cannot do anything about the PCB thickness, and I worry it could cause my Tweezer accessory to become a looser fit over time. The manufacturer needs to address this because there are no other Kelvin Clips available for the DE-5000. I'm giving it 2 stars rather than 1 because the kelvin clips are very nice. It's the connection to your DE-5000 that is horrible.

Calibrates and works fine with DE-5000

Habe zu meinen DE5000 auch den TL21 mit den äußerst kurzen Anschlüssen. In den Bewertungen wurden auf das Problem beim Anschluss an das DE5000 hingewiesen. Habe mir das angesehen und dann die Anschlüsse so wie beim TL21 angeschliffen und es funktioniert. Die Kalibrierung läuft ja über das DE5000, somit ist man bei der Messung etwas komfortabler unterwegs. Mit den ca. 30 cm Kabel und den starken Klemmen kann man auch direkt an der Platine messen.

Too tight to fit then does not lock in like genuine unit does. Also does not contain a shielded wires as genuine unit does.

Seems well made and the DE-5000 auto calibration process found no faults.

Bought for use with my newly acquired Hantek 1833C LCR meter - it fits and functions perfectly!