Berlinzo Premium Clear Ice Cube Maker Mold - 8 Large 2.1-inch Crystal Clear Ice Square Cubes for Whiskey and Cocktails - Easy-to-Remove Ice Cubes Mold - Storage Bag & 24 Ice Prints Included, Black

The process is a little clunky, and it can sometimes be frustrating but with a little practice and patience, you get beautiful, crystal-clear ice cubes every time. I gave this ice cube maker 5 stars because it is relatively inexpensive for what you get, the materials are high quality with good fit and finish. The drawbacks (such as taking 30 hours to make only 2 ice cubes) are really a function of thermodynamics rather than the product itself. (See the end of this review for the TLDR "how it works".)I have been using this ice maker for around 18 months now and here is the process I use to get crystal-clear cubes every time:1) Start by cleaning and drying all the parts. If any of the parts are wet when they go into the freezer, the unit can be extremely difficult to open up and can result in the corners of the ice cubes being chipped. Also, if you're refilling the ice maker after using it, make sure there is no residual ice chips or drops left in the mold.2) Assemble the components. First, make sure the foam insulator is pushed all the way down into the plastic shell and then the plastic reservoir is pushed all the way down into the foam insulator. These parts all fit very nicely together and it will be apparent from the way the lips of each piece connect when they are properly assembled. Leaving a gap between any two of these pieces will result in substandard ice.3) Fill the reservoir to the indicator mark. I use reverse-osmosis (RO) filtered water but I've also used tap water successfully. Use lukewarm water for best results.4) Assemble the silicone ice mold and then slowly let it settle into the reservoir. Don't push the mold into the reservoir or you'll end up with incomplete or malformed ice cubes. A small amount of water should bubble up out of the 2 vent holes in the mold. Make sure the mold is completely settled into the reservoir before proceeding - again, the parts fit together nicely so it will be obvious when settling is complete. Use a towel to dry any standing water on top of the ice mold.5) Use two hands to lift the entire assembly and place it upright in the freezer. Lift it by the side handles. Do not squeeze the assembly (by lifting it with one hand) or you'll end up with incomplete or malformed cubes. The goal here is to have no additional water bubble out of the vent holes as you put the assembly into the freezer. Leave the mould in the freezer for 30 hours.6) Pull the silicone mold out of the reservoir, pull the two halves apart and gently remove the ice cubes. Cubes can be stored in the included silicone zip-lock bag (the bag holds 6 cubes) for several weeks. Cubes can be stored in regular freezer Ziploc bags for a couple of weeks but longer than that and they start to degrade. Use warm water to remove the ice in the bottom of the reservoir. Dry all the parts and you're ready to start again.How it works: the key to the process is the insulating layer on 4 sides plus the bottom of the mold. The mold orients the cubes with one corner up (the non-insulated side) which is exposed to the ambient air in the freezer. This orientation along with the insulation forces the water in the mould to freeze from the top down. As the water freezes, it pushes the entrained air (and any impurities) down into the reservoir, leaving crystal clear ice behind in each cube. (The reservoir holds about 3x as much water as needed to make the cubes. This extra space give the water with entrained air a place to go as the cubes freeze.) The insulating layer is a bit thin but using warm water in the mould ensures that the process proceeds properly. The whole assembly is kinda bulky and it would be quite a bit bulkier if the insulation was thicker so I think this is a good design trade-off.

My first purchase of this kind and it was simple to use and works great. Makes perfectly clear ice. Going to buy other products of theirs.

Makes perfectly clear ice cubes every time! My Manhattans taste even better. Easy to make big ice cubes and much cheaper than buying them at the grocery store. The unit does not leak in my freezer--as long as I don't overfill the water in the holding tank. Ice cubes are easy to remove from the silicone molds. Great product!

Works pretty well BUT it’s not that perfect craft ice. It’s also pretty big for a couple cubes but I guess that’s what is needed to make the big bubble less cubes

I have purchased 4 or 5 of these kind of clear ice cube maker. This one works really good. The cubes are the the easiest to get out of the Molds. They are definitely over 2 inches. The only down side is that in my small mancave bar freezer, it takes at least 18 hours to freeze. The base is long do make sure you have room in your freezer. In 3 days, I have 16 nice cubes. Sometimes I get a weird deformed cubes. I suggest that you rotate the unit after about 12 hours. Cheers!

Love this clear Ice maker. Ice is crystal clear and last longer than cloudy ice, I don't know why, but it does. What I do know is that your drink tastes better with the clear ice because the impurities that make the ice cloudy sink to the bottom leaving a clear and higher quality product. I use hot water in mine straight from the tap. I fill it up just past the divider, insert the ice mold, then fill three mold the rest of the way up. My freezer takes 24 hours and it's perfect every time.

Ice quality is good , is a long process to get 4 ice cubes.Secondly , it is hassle to remove the 4 ice cubes which are like sediments on bottom of the box each time.Takes a long time to take them out prior to freezing another set for ice.

excellent, does ice perfectly, release from the rubber mold is easy and clean