12inch x 100 feet roll of Paper Transfer Tape with a Medium to High Tack Layflat Adhesive. Works with a Variety of Vinyl. Great for Decals, Signs, Wall Words and More. American Made V0821

When cutting with my laser, I need to tape the material to keep it from scorching. I use this tape all of the time. It's the perfect size. It goes on easily, and is easy to remove.You do have to watch it while it's cutting. Sometimes the tape will raise off the material and can cause it to burn.Note: the manufacturer has a disclaimer that it shouldn't be used with lasers because it can burn.I find that if you burnish it really well, it minimizes the risk of rising.

I originally had the Cricut transfer tape which let me tell you is good, too good is the problem though. It sticks and sticks hard to the vinyl. It’s overpowered to the point of not being able to get a solid transfer because it would cling so tightly to the transfer tape then would leave lots of residue to be cleaned after the fact. This paper transfer tape however grabbed just enough to make easy transfers and to top it off, no residue left behind to clean off the product I leave the vinyl on. The roll is perfect size in amount needed for the price you pay.

I really like this transfer paper. It does work very well. It’s easy to remove and does not leave residue on your vinyl. I do have the larger roll and the smaller roll and I just cut the size that I need. If you’re looking for a good transfer paper this is definitely One to use I think the cost could be a little less but it’s still a great value because it actually works

I'm using this to mask for laser engraving. First, I acknowledge that this isn't its intended use so I'm not giving it a terrible score, I'm just letting anyone else who might use it for this same purpose know what to expect.This tape will stick to most dry woods but it will not stick to any woods that have been oiled, like finished spoons or cutting boards. I've used it successfully on cedar, oak, walnut, cherry, maple and hickory. The For a good seal the wood needs to be pretty flat, especially if you're going to be spraying a paint or stain over it. It comes off easier than masking tape which is nice when you have lots of little pieces to remove after the engraving.

I recently purchased vinyl ease paper masking for my woodworking projects and I couldn't be happier with the results. This product is a game changer when it comes to preventing char and burn marks on wood while lasering.The adhesive on the vinyl ease paper masking is strong enough to stay in place during the laser engraving process, but also easy to remove without leaving behind any sticky residue. This makes it a breeze to protect the surface of my wood projects without causing any damage.Additionally, the paper is durable and can withstand the heat and intensity of the laser, ensuring that my designs come out clean and precise every time. It's also easy to cut and manipulate, allowing me to customize the size and shape of the masking to fit my specific n

I bought this to use with stencil vinyl and it worked well for me. I have also used it with permanent and removable vinyl, and is now my preferred transfer tape.. I like that the roll is large and lasts for a long time. It’s 12in wide so it covers the cricut mat. Be aware it’s not as sticky as cricut transfer tape, it is not see though and doesn’t have the graph lines.

This product left a sticky film and residue that will not come off my materials. I have tried soap, oil, WD40 nothing removes it. I placed this on multiple sheets of acrylic and glass that I cut and engraved and planned to paint the next day. After painting my items the next I went to remove the masking tape and every single sheet of material was left with this residue that wont come off. Some of my materials come masked with tape already those items were stored in the same area as these but none of those have this issue so this transfer tape is NO GOOD if left on for long periods of time.

This transfer paper has been a godsend for masking wood prior to laser cutting and engraving in my Glowforge. I wish I'd seen a review state this as bluntly when I was searching up and down Amazon for the right paper (you know, so I wouldn't poison myself by cutting the wrong material and accidentally release poisonous gas :) Easiest way to unroll I've found is to attach the end to a counter, unroll just a little bit more than you think you'll need, then place on wood pushing down the center firmly with a flat hard edge. Then I cut the end and finish pressing the paper from the center out. I've not had a single problem with getting it to hold on many different types of wood, whether it's sanded, stained or unfinished, as long as the material is completely dry and free of debris and it's pushed down with a firm flat object (like the side of a credit card). Waiting on my second roll and will order again.

This paper is the best for transferring! It is minimally sticky which makes it way easier for me. Not tacky enough for some people, just pay attention when pulling the backing off the vinyl to make sure everything sticks to the transfer paper… it’s zero fight compared to clear name brand transfers that are so sticky and leave residue on your cutout sometimes. Not this stuff. 5/5

Works perfectly with the circuit!

By far the best paper transfer tape I have ever used. This stuff saves me so much time when prepping my wood for the laser. Every project comes out flawless without the burn residue on the final product. The only thing I do not like is the price for the amount. You can go through it fast! Mind you, you can peel off access on other pieces and reuse! So glad I found this!

The adhesive isn't the best as it takes a couple of tries at pulling off the vinyl, sometimes but it's better than all the other competitors stuff out there. Not exactly the bang for the buck either. It is easy to remove at the end of the job, though

The roll is very difficult to peel making it difficult to use and keep straight and flat.Creases very easily and precutting is a challenge.It does exactly the job it is meant for though and has the perfect adhesion level for transferring vinyl.