Thermal Grizzly - PhaseSheet PTM (50x40mm)- High Performance Thermal pad with Phase Change Material | Durable, not electrically Conductive | for CPU, GPU & Electronics Cooling

Has great thermal performance. But it is hard to apply. If you refrigerate it and remove the plastic layer(hardest part) then it is easy. But I did without refrigerator. Now my laptop (ThinkPad P15 Gen 2) runs in a stress test at 100 watts for 1st 5 minutes at average of 90°C compared to previously with cryofuze 5 where it would be 50 watts at 80°C . It would run for higher wattage but limitation of VR cooling limits the laptop. Got it is for ₹1699.

Amazing performance, it says to wait for 10 cycles for optimal temperature drop but as soon as I changed my laptop cpu temperature dropped from 90- 97c to 75 - 84c on heavy games. I bought it for 1.7k , it's pricey compared to other brands or sellers but you can rest assured of its authenticity and for laptops you can use it twice. P.s use tweezers to remove the protective films in top and bottom.

This thing slaps.

Best thermal upgrade I’ve done till now. GPU 59–65°C, CPU under 75°C and way less throttling. My LOQ laptop finally runs cool. Also, definitely keep PTM7950 in the fridge before application, tried applying it before cooling and it was a complete mess. 10/10 for cooling performance. 6/10 for application ease. Highly recommend

Amazing performances and thermals. Used both in laptop CPU and GPU. Good value for money.

I own a Lambda Tensorbook 2 (basically a Razer 15) for a few years now. Some days ago, I opened it up, and re applied thermal paste (MX-40) carefully on GPU and CPU. The improvement was significant, but it showed two hotter spots which were still causing some throttling. So I decided to try this product. I left it in the fridge about 10 minutes, cleaned the old paste, cut the sheet into two pieces for GPU and CPU, and applied the sheets over them. BOOM. 5 seconds. The peel is a bit hard to remove, technical tweezers helped. I cut it slightly bigger than the chips, and still got some left for a change in the future. TEMPS ARE INSANE! The PC sits now at 4300 MHz across all cores in PL2 (boost mode) with avg temp around 80 (more or less 20 seconds boost, 90 W), and at 3700 all cores in PL2 at about 60 degrees. ZERO THERMAL THROTTLING. The GPU couldn’t get hotter than 61 degrees in 5 minutes of test load. My fans are now basically never on. I am very happy with the purchase.

Excellent getting 30c to 70c on hotspot watting for inbeding on a rx9060tx gpu 30c to 45c have got a few heat sinks an the back plate thou.

Excellent cooling. CPU maintained at 38C at idle versus 46C with cryosheet which found has uneven clamping when replacing to phaseshift.

Suggerita dall AI e Utilizzata per cambiare la pasta termica della mia Xbox series X ormai secca e inutile dopo 5 anni e devo dire davvero efficiente ! Già dalla prima accensione tira fuori un calore che ricordavo solo a console nuova! Non è molto difficile da applicare, bisogna prendersi il giusto tempo e magari guardare un video su YouTube prima. La console è tornata silenziosissima ed in previsione dell estate e considerando le condizioni della pasta termica originale ormai asciutta è completamente fuoriuscita di sicuro ne salvaguarderà la durata e lo stato di salute a lungo. Consigliatissima! Raccomando di metterla in freezer 8/10 minuti come consigliato dal produttore per poterla tagliare con precisione e di fare qualche ciclo di mezz ora accesa/spento per portarla a regime .

Normal termal macunlar kadar dereceleri düşürüyor ama diğer macunlar 1 hafta iyi, 1. ay bittiğinde üzmeye başlardı. Bu ise çok daha uzun süre dereceleri koruyacağı belli. Paranız yoksa da biriktirin bunu alın, uzun vaade de çok daha iyi olacak. Uygulaması zor, videolarını izleyin.