ICBEAMER 34.6" Sunroof Wind Deflector, Fits 30-33" Sunroof, Dark Smoke

This is on my 2013 Lexus ES350 and it fits perfectly!! It appears to be a good quality product, not flimsy. Take measurements before you buy!! Clean the area thoroughly before you apply. I removed the protective adhesive strip entirely and eyeballed it into position.. it adhered instantly and looks great!! Try to get it right the first time as adhesive tape will lose its adhesion if you stick/unstick frequently.. and you may have to replace adhesive tape >> I recommend Gorilla 2 sided tape!! Im a DIY and hate to send items back and wait for replacement item so I just make it work. If your roof curves are extreme, I suggest you reinforce with more 2 sided tape on both ends to help keep it in place. Overall, I'm happy with the product/results and expect it to last and stay in place for a long time.

Looked great but started coming off after only a few weeks, the double sided tape included isn't the strongest I put mine back on with gorilla tape been holding good since

Not only was this deflector cheap, see through, and so flimsy it bends in the wind... but as you can see from the photo, after a month of normal driving in above 60º temps, the deflector is detaching from the adhesive strips. I followed every step and you can see that it's not detaching from the car but from the deflector itself. Don't waste your money with this product as it's trash and they won't refund you until you take the time to ship the piece of trash back to them. 0 out of 5 stars.

The product arrived on time but it had 2 superficial scratches on it. I applied some rubbing alcohol to the scratches and the scratches disappeared. The product looks nice on a car but I would STRONGLY advise that you do the following in order to ensure proper adhesion to the roof of your vehicle: (1) CLEAN the roof of your vehicle with rubbing alcohol in the area where you will apply the adhesive tape in order to ensure that the area is free of dirt. (2) Use a heat gun (on the lowest setting) to soften the tape for about 12-15 seconds (I replaced the factory adhesive tape with thin 3M double-sided tape [$8] because 3M makes the best tape). However, I still used a heat gun to heat the 3M tape to maximize strength adhesion. (3) Apply the deflector to the car roof and press firmly down on all edges of the deflector to ensure adhesion. (4) Use a heat gun again for a couple of minutes to go all around the adhesive edge of the deflector to reheat the tape underneath it so that it will create a strong bond between the metal of your car, the tape, and the plastic deflector when the tape cools (chemistry students know how heat effects molecular bonds). (5) Do not move the deflector for 2 hours (preferably 6-8 hours) to allow the tape adhesive to cool and bond. This should provide a long lasting bond that should hold the deflector in place. Please remember that you can always go back and uninstall a problem adhesive area of the deflector simply by reheating the area with a heat gun and re-applying some additional tape or simply pressing down on the existing tape once the tape becomes soft as a result of the heat. If you fail to follow the above instructions then your deflector may fall off of your car because the force of wind is at it's greatest force on the roof of your car as you drive.

The top of your vehicle is contoured so best to do these in the heat. follow the instructions after you get it centered and exactly where you want it. take a maker and mark where the back ends on each side go, make sure both ends are attached firmly where you want them. then do corners to center. press down and a bit back on bend. Look to makes sure your tape is touching. the straightness of the shield will bow up in middle so viewing the actual adhesive tape contact, continue pressing till it has no gaps.. I then sat my vehicle in direct sunlight to help the shield to adhere to the contour of my vehicle. an hour later i took for spin in 20mph winds and it held nicely..... if you clean the surface with windex, IT WILL STICK.

Product is good but adhesive is not very good. The deflector comes off all the time so I had to purchase # M heavy duty tape. Maybe the manufacturer should switch adhesive tape

Great customer service! I ordered the wrong size and they exchanged it with the right one. The wind noise is down and looks great! Not to mention about $30 less than a retail auto parts store!

looks great easy installation, perfect fit, adhesion stays solid. great buy all around

i used it to cover the missing part on my sunroof for explorer fort 2014

物だけみるとチープ感が否めないなぁって感じでしたが、つけてみるとそれほど気にならないかな、、？ 付属の両面テープで簡単装着出来ましたが、耐久性にはやや不安があります。

وصلني المنتج مكسور تماما

All good it fits perfectly😀

Product Quality is fragile . Need to return .