WEN Miter Saw Stand, Collapsible and Rolling with 3 Onboard Outlets (MSA330)

The stand was simple to put together and a very inexpensive way of having a rolling stand for my miter saw. 10” cordless Bosch slide miter saw fits easily on the mounting brackets and is stable during use. Being a stand that folds down and has wheels makes it easy to move around the jobsites that I’m on. Having 8” rubber wheels helps with this. These wheels also make moving up and down stairs easier. The wingspan when extended is reasonable. The only disappointment I’ve had with this stand is that I can’t fold and store my saw in a vertical position on its own. Even extending the one roller near the wheels fully doesn’t make it stable enough. It might work with a smaller or lighter saw. Not the end of the world when strapped against my shelving system but I wish it could when on its own. For under $100, and 20 mins of my time to put together, this certainly wasn’t a dealbreaker for me. Having used the DeWalt dwx723 or horses/job tables over the years, I’m enjoying rolling my miter saw around for work.

Sturdy and strong. Very good value if purchased on sale. Even the wheels are high quality. Best assembly instructions I have seen in 10 years (intentional humor included). I had hoped to keep the miter saw permanently attached to the stand but found it was too unbalanced for transport or storage. I keep a 10 inch Metabo miter saw permanently attached to the mounting brackets and it turns out to be easy to carry this lightweight saw to and from wherever I set up the stand. Easy and quick to attach or detach the saw. Stand rolls easily and is simple to set up or take down. I am pleased with this purchase. Makes using the miter saw much more enjoyable.

Overall I am happy with the purchase. The stand is relatively well constructed and I was able to mount my SKIL 10" dual bevel sliding miter saw. The brackets are relatively beefy. I do have a few minor and one more serious issue: 1) Serious issue: As it is, the miter stand can't be stood up, even if you rotate the roller the other way so that the angle bracket rests on the floor. Following the advice from other reviewers, I added a 2x4 piece. I had to trim it a bit so that it's only 3" high (2x4's are normally 1.5" x 3.5"). I also made it slightly wider than the wheel base to add more stability. I drilled a couple of holes on the angle piece and permanently mounted the 2x4 in place. As it is, it doesn't interfere with the operation of the saw. This way I don't have to remember and locate the scrap piece of lumber. 2) The power outlet bracket (which also holds the wheels) are mounted with two hex head matchine screws but they didn't provide a hex key. It's 6 mm. So, find one before you start assembly. 3) Only one leg has a level adjustment screw and it's a bit squirly. You have to fiddle with it to adjust it and there is a plastic locking nut on it. 4) The power outlet cable is really short, so you really need to run an extension cable to it, I am planning on attaching an extension cable permanently to it. 5) The handle is a bit difficult to mount. You have to fold the legs on the handle side to have access to the bolt holes. 6) I highly recommend installing the mounting brackets to the miter saw outside as it's difficult to align things on the stand. Also, one of the bolts (the one near the locking lever) is hard to get to. You have to put the bolt in at the locking lever side first, then slide the bracket forward so that you can get to the other mounting hole. 7) They provided 4 bolts, 4 washers and 4 nuts. I would have preferred a wing nut. The washers were too small for the slots on the mounting brackets. You need larger washers. Overall, at below $100, this is a good value and certainly beats me building a stand myself.

Nice portable stand it works well with my DEWALT 60V Lithium-Ion 12 in. Cordless Sliding Miter Saw Model #DCS781B. I did replace the saw mounting bolts that came with the unit. I had stainless steel with acorn nuts on hand. The extension is plenty big enough. For trim, work, and votes nicely for storage or transport. Most of the reviews and reports were accurate representations, does not store standing up, but I don't know that I would want the weight of my saw hanging like that for an extended time on the camlocks. I would definitely recommend this over many others that I looked at and put my hands on in the box stores. Easy setup and easy store, assembly was quick and straightforward. 1/4" Allen wrench, 1/2" nut driver or socket and Large #2+ phillips screw driver. Good product and a good price!

The first thing you SHOULD notice is the Dual Tube extensions. This is twice the support of the single square tube designs and because it is ‘spread out’ about 6 inches, makes the support MUCH MORE stable and has ZERO want of ‘twisting!” Each tube has it’s own setscrew handle too. The stock support rollers are what we call in the Engineering World, “VERY Meaty” with a good design along with the simple permanent step that you use for a material ‘bump stop.’ The handy outlet is an ‘off the shelf’ triple plug and mine actually came with an extension cord. The wheels are decent and are held onto a solid shaft with an “E” clip instead of lesser quality means. The Saw mounting is simple and clamps FAST as well as solid. The clamp action is very easy work with a mounted saw AND the ‘clamping action’ is actually adjustable for wear or preference! You can also simply pop the clamp handles ‘up,’ slid it either way to give you more length on either side and pop the handles back down. The Legs are sturdy, one has an adjustment to ‘even the stand out' on the floor and the material holder ‘fold outs’ on the legs are pretty darn “beafy” too! The few things that would make it almost perfect are a couple washers for the wheels against the “E” clips and “Stop Nuts” (plastic insert style or locking nuts) for the Handle and the mounting of the wheels. The Wheel mounts with bolts that actually also mount the Outlet’s Plastic Housing. Structurally this is acceptable, but you can’t expect a “Lock Washer” to hold without backing off from Saw vibration or rolling the thing around the yard. Trying to use a Lock Washer to fasten plastic never works anyway as the more you tighten, the more stress on the plastic, then it breaks. I replaced mine with two bolts/nuts each which was a simple step to make it so much better. Other notes: Yes, you have to take the saw off to move it. My saw alone weighs 45 pounds so I would not even attempt to leave it in place. The Saw mounting bolts are pretty small and I replaced them for my Saw. The Side supports actually move up and down at an ANGLE so instead of trying to place them precisely, get them to height and THEN simply move the saw. The saw can be located anywhere on the main tubes and with the extended tubes you can get more than 6 feet from the saw. If you need more length, or a need more strength, or you’re a contractor, this is probably not the Stand for you. PS. This is about the same as “amazon’s choice” that's about $20 more!

Better than other wen products I have purchased and hated. I purchased a similar product, almost exact same design from a different brand. I was happy as I started assembling the stand until I realized the handle was broken. I returned that one and purchased the wen since I could tell they were almost exactly the same. Assembly was easy enough. Some parts of the powder coating were rubbed off even though the packaging was intact. Additionally one of the plastic screw handles was broken. I would rather epoxy this handle on the bolt than deal with returning the stand.

I just purchased a compound miter saw and also bought this stand as part of a package deal. This is my first power saw of this type and I wanted a good start. I’m quite pleased with this stand. It was easy to assemble and I was impressed with the quality of the materials and engineering from the get go. I love that it‘s foldable and equipped with wheels to make it portable. A great feature because my garage doesn’t have a lot of spare space. My Skil Saw mounts perfectly to the support rails and has a very solid feel. The electrical outlet on the frame is also a helpful feature. The price was very reasonable for such a quality piece of shop equipment. Overall, I don‘t think I could have found such a perfectly matching stand of this quality for this price anywhere else.

This thing is absolutely amazing. Well built, easy to put together and holds pur 12" compound sliding saw great. No issues at all. Highly recommend.

Nice Stand and fit my Miter Saw perfectly solid and strong and so much easier to cut on. I am very happy. I need some sides with rollers on it to hold longer boards, especially after they start cutting. But the ones that come with it do help most projects.

Es lo que esperaba y es la adecuada para mí ingletadora Craftsman

Le quedo perfecta a mi sierra ingletadora milwaukee, muy resistente.

Set up was super easy, solid stand, folds up nicely, more stable than I expected. The only thing that I didn't like was the flat washer that came with it were really thin and cheap. Used some thicker washer and mounted the saw nicely.

I had a saw for several years and needed a stand. I am still buying cheaper tools until I can afford the higher quality items. This stand works well for me. It’s very sturdy and built well. However it’s not as easy to fold as some stands at a much higher price. My advice is if you are just getting into tools for a hobby then this is for you. If you are experienced and have expensive tools, get something like a Dewalt folding stand instead. For the price, this is the best bang for the buck.