amFilm Ultra Glass Screen Protector for Samsung Galaxy Note 10 Plus, UV Gel Application, Compatible with UltraSonic FingerPrint Scanner for Galaxy Note 10 Plus(2019), Tempered Glass, 2 Pack

Hello all!First time posting in a while, so forgive me if I'm a bit rusty. I just got my Samsung Galaxy Note 10+ yesterday, and my amFilm Ultra Glass Screen Protector today, so I thought I'd write up a little review. Sorry for no pics, but I was busy installing and trying to keep things dust-freeI've used Whitestone in the past but was disappointed with both my Note 8 and 9 installs, primarily because of the LOCA spiderwebbing on the edges. I figured I'd give another brand a shot, so I went searching here and found the amFilm Ultra Glass Screen Protector. A quick trip over to Amazon, and $40 later (for a full kit including *2* protectors) and here we are!PACKAGING: The box is nice - wider and flatter than the WS product. It's clean and simple, but professional looking. Plus their website and install video are well done also. Inside the outer box are three smaller boxes. The largest contains the plastic frame, screen protectors, and wipes (I think). The medium size box contains the UV light and the MicroUSB cable. It appears to be identical to the WS product, but I don't know this for a fact, so take that for what it's worth. The smallest box contains the LOCA (2 tubes), extra absorption pads, plastic pin, tabs to place over the speaker, a bubble level, and a weight. Everything you need comes in this kit, including plenty of wet and dry wipes, microfiber cloths, and dust removal stickers. On the packaging is a QR code to go to the install video.PRODUCT: Everything seems to be on the same quality scale as the WS product, with a few minor changes - 1) there is no LOCA applicator "bridge", you have to aim and dribble the solution by hand, 2) the pin is different - there's no more tilting the entire phone to move the liquid into position - the pin is angled and sets the glass down at an angle, and 3) the "fingerprint" weight (more on this later). Otherwise, if you've done the WS before, this isn't significantly different.INSTALLATION: **REMINDER** REMOVE the factory plastic screen protector and clean your screen THOROUGHLY before proceeding! I ALMOST forgot, which would have been a disaster! I watched the video twice and didn't see any mention of this, so amFilm, here's a tip for you Anyway, installation is straightforward -put the little feet on the bottom of the phone to bring it flush with the pins inside, make sure the screen is 100% clean, install the sticker over the speaker, apply the liquid (making sure to absorb any "splatter" before proceeding!), peel the protective film off the glass, place it, and pull the pin. Once the liquid starts to spread, put the weight where the fingerprint sensor is and let it settle and "ooze" for 3-ish minutes. (NOTE - it's hard to locate the fingerprint scanner, so you might want to mark the frame in advance with a Sharpie (another tip for amFilm - marking that plastic with some kind of raised bumps or hash marks might be a good idea, or maybe a film for on top of the glass that marks where to place it - just a thought). After that, it's bake-time under the UV light, then you're done.RESULTS: I'm very impressed so far. The glass appears to be nice and clear, and I can't even see the little "spots" in the corners others mentioned. I lucked out this time and no dust specs at all. No bubbles, etc. the fingerprint scanner appears to be working fine, although I haven't re-registered anything. It DOES require a little extra "umph" to scan, but that's not a big deal. Part of that could be me getting used to an in-screen scanner. There was minimal over-oozing, and the pre-installed pads absorbed everything fine. Barely needed a wipedown afterward.FITMENT: There appears to be no flaws in placement using the guide, or in the fitment of the glass. It sits flat, and lines up exactly where it should. The cutout for the front-facing camera is exactly where it should be, and it's not overly-exaggerated in size. The edges leave plenty of room for putting the phone in a case (I've tried 4 so far, all fit without touching the glass edge, so there's no worry about case push on the glue). The bottom edge is just a tad bit short, maybe a 1/16", but that could be allowing for larger cases (I don't use the big bulky ones, so IDK).OVERALL ASSESSMENT: 4.5/5 Stars - Great product, especially for the price. I'll keep you posted on long-term wear & quality, but for now, I'd say it's a great deal versus the competition.

I THINK THESE ARE THE BEST FOR PROTECTION. I DO HIGHLY DEFFINATLY FOR SURE RECCOMEND FOR ANYONE WANTING BEST PROTECTION FOR THEY'RE PHONE ITS AN INVESTMENT.

Overall a great product with no real alternatives still available, but there were some difficulties with the installation.1. The list of included components and the provided installation video made note of a dry wipe meant to be used between the wet wipe and microfiber cloth cleaning steps, but my package did not include this dry wipe.2. A tiny sliver of the adhesive bottle flaked off during the application of the adhesive, and I didn't notice until after the screen protector was applied. It's not particularly noticeable, but it is definitely there and more or less permanently installed on my phone now.3. The adhesive spread far more than in the provided installation video, perhaps due to a temperature difference. This meant that the "ramp" used to lower the screen protector onto the adhesive did not allow it to make contact with the adhesive until the very end, which meant that the spread was inconsistent and created air pockets.4. Said air pockets were quite simple to gently work out to the edges, but doing so caused some of the adhesive to escape the jig. Because the UV light is directed from above, I was able to simply wipe away the uncured adhesive from the edges after installation.5. The installation video showed silicone leveling pads for the back of the phone, but the pads provided were made of foam. Removing these pads after installation tore the foam and left bits of glue and foam stuck to the back of my phone.I wish the installation video had made note of the potential for the glue to spread quickly and interfere with the application, that the adhesive bottle had not flaked off bits of plastic, and that the included pads had been the silicone ones from the video.