amFilm3 Pack Designed for ASUS ROG Ally 2023 /ROG Ally X 2024 Screen Protector 7 inch, Tempered Glass, Transparent Ultra HD, Anti-Scratch, Anti-Fingerprint

Super easy to apply, fits perfectly, can still use the touchscreen function. Super nice that it comes with 3 in case you mess up an application or one breaks.

Fits perfect on my Rog Ally (black one) easy to install and good price for 3 protectors.

Works well. Bought this twice because friends wanted to use on theirs. Still holding up with no air bubbles. Fits even with my dbrand case installed.

Perfect fit for the Rog Ally X, easy to install if you have experience installing tempered glass screen protectors. I haven’t noticed any difference in touch sensitivity and it looks great.

The product comes with everything mentioned and the product is good when you finally install it for your liking. Heres the issue with it tho, the product itself when you mess up after line it up to your screen the adhesive is so strong that it seperated from the tempered glass so basically saying that if you mess up once the screen is gone. Overall, the product is good it does the job, and it feels amazing just be careful installing it. I wish this product came with an outliner or something to better place it on the ROG. Hovering over it and hoping for the best is not enough. I basically lost the whole pack because of the corners.

I just installed this today and wow it's really nice. It's really edge to edge. There really isn't any margin for mistakes. 😁 The edges are 2.5D! The clarity is awesome. You can't even tell that you have a protector on. Here are some tips below though.* Turn off any fan or AC.* Get a bright light over your Ally while it's turned off.* Clean off your screen with the wet one first then dry it right away. Use the microfiber cloth first though to wipe away any dust or so.* Cut off most of the plastic holders as you won't need them if you will be using the guide method instead.* Use the guide stickers. Two should be fine and tape the glass screen protector to the top of the Ally. Make sure you align it first before securing it. Also make sure the holder tabs that guy cut off are on the top while the pull tab is on the bottom side with the tab on your top left.* Put your glass screen protector up and away to the top. Now use Scotch tape or so to dust off the screen. Make sure not to touch the screen with your finger and only use one side of the tape while doing this. If you have tape dusters from other screen protectors you could use that too since these for some reason didn't come with any which are needed.* Make sure there is no dust left. Go ahead and grab your glass screen protector from the top again. Again the glass should be attached to your guide stickers with the Ally. While holding the glass around 45 degrees go ahead and pull the tab for the bottom layer. Don't go too fast or slow. Just medium speed will do fine.* Once the bottom layer is out then use your finger push down on it from the top middle to the bottom middle. This will spread thr protector out while not leaving any air bubbles.* Wait for the whole protector to fully sit first. Now use your finger and push down on the edges while going along them. Make sure you touch every single side and corners.* Now remove the top layer using the holding tabs that guy cut off earlier. Go upwards while taking off your guide stickers at the same time.* Lastly use your white microfiber cloth and secure all the edges again one more time. Enjoy your Ally with some piece of mind now!

Only one negative was the placement sticker, that had thumb tabs to hold onto, on the front of the glass, was not adhesive enough to stay on it while it was being set in place. The tabs to hold it had started pulling the placement sticker off before it was in place.Pro: Glass edges line up snuggly to the edge of the screen and the beveled edge makes it look fantastic! No glare and very crisp view!I found a a different protective glass that came with sticky tabs attached to the sides of the glass for easier installation. This way the glass would be set in place on the device and the sticky tabs would attach to the device on the long top edge, and make kind of a door with the sticky tabs being the hinges. Then, with the hinged sticky tabs in place, would open the "door" and remove the adhesive cover. Then, guide it back it into place with minimal lining up as the tabs did most of the work.This applicator doesn't have that feature so I used masking tape as the sticky tabs and ran through the process.

There are a lot of these knockoffs of screen protectors, because the "amFilm" brand knocks it out of the park every time; however, I, like many others, made the mistake of pre-ordering screen protectors for a device next to no one has heard of, and it gave a lot of third-party, cheap, new sellers an opportunity to sell incompatible protectors.These amFilm protectors from TechMatte fit the ROG Ally ***PERFECTLY*** - I'm talking edge-to-edge, bezel-included, tempered glass protection.There is one slightly inconvenient con, however, just to make you aware: for some reason, the film with the tabs used to align the protector had almost no static adhesion on any of the 3 protectors I applied - if you hold it above the device, the tabs start to be outweighed by the protector, and if you stay like that long enough, the protector WILL fall away before you get a chance to put it down. So, clean well, use the stickers to get the pesky flecks of dust, line it up (I highly recommend lining up the top and left edges), and place it down. Unlike the Nintendo Switch, the Ally's sticks will get in the way of your applicator tabs, so again, move quick.