Westinghouse 7840900 Industrial 56-Inch Three-Blade Ceiling Fan with J-Hook Installation System, White, Wall Control

I've bought quite a few products lately to try and combat the heat here and this fan is one of them.Our main issue is we just recently had a baby and the nursery is above the garage. Being above the garage and having a traditional attic, that room gets very hot and is not easy to cool down.When we built the house we did make sure the garage was fully insulated, so all walls and the ceiling. I have done a few thing to help the garage not heat up as much and I am working on modem insulation in the attic as well.What I did with this fan though was put it in my garage. Right now there isn't much else I can do with my garage other than air condition it and I have no plans to do that. So, I mounted this fan ok the ceiling in the area that would be about center to the nursery above the garage.The thought was that during the day the heat builds up in the garage and rises to the ceiling which in turn heats up the floor of the nursery. Putting the fan there will help pull the heat off the ceiling and keep the garage a more uniform temperature. It also helps to cool down our car after driving it and then parking it in the garage which helps prevent the car from heating up the garage as much as it normally would. I also plan on moving the yard equipment and things out to a storage shed so that I can put up cabinets and put down a floor coating to make the garage a cleaner place to work on things. So this fan will help make working in there more bearable once I am finished with all that.So far I think it has helped. I wasn't expecting huge results since it's just blowing around the same hot air but, for $70 it was worth a try. It also wasn't necessarily about saving money each month as much as it was about making that room easier to cool down. Because as it is now, on the hottest days, we can't get the room down below 76-77 and it hasn't its own dedicated thermostat for that room. So if my bill stayed the same but I could cool that room better I'd be very happy.I tried to measure the temperature of the floor before the fan and after and it seems to be about 3-5 degrees different than before. It's hard to get concrete results because the temperate and humidity etc....have not been exactly the same but they've been close. The temperature before was around 80-85 depending on where and now it's around 77-81 depending on where.As far as the fan itself, it is probably the easiest fan I've assembled and put up. We just recently put up one in the nursery that was not as simple.My control box looks quite a bit different than others, I'll post a picture, so I did not replace it as it's not too bad looking.When cranked all the way up, this fan moves a ton of air! I can see why people said it was loud. It's not the fan operating that's loud, it just blows so much air its like a planes propeller on our ceiling!Because mine is in the garage I could not use the long rod it came with as mine is in between the ceiling and garage door. So I just cut down the rod, drilled two new holes and reassembled. The holes I had to drill hold in the small metal bar which is what secures the ball joint that mounts to the bracket on the ceiling, so it's very important to be able to drill those two new holes before you cut up the pipe.Because I cut it down, I wasn't able to use some of the decorative shrouds that hide the wires, but that's ok since it's in the garage.Assembling the blades was a piece of cake and so was mounting. Just throw a couple screws to the mounting bracket and ceiling and then hang the fan. Once it's hung you can splice the wires and you're done!Now, where I put this fan was not designed to have a fan or even a light, it was just a smooth ceiling. All I had was two outlets on the ceiling which power my garage door and my remote garage door opener. It's one we got from our security company so we can open and close the garage from our phone.In order to make this work, I bought a two outlet adapter, from Amazon, so that the fan and or remote sensor could be plugged into the one outlet. I wasn't worried about load on the circuit since the remote opener barely uses any power.Next, I took an extension cord (VERY IMPORTANTLY A THREE PRONG GROUNDED CORD) and wired it to the fan wires. Because this has no light it would've been an easy white to white, gray to gray and black to black wiring. However, this also comes with the control unit that needs to be wired in. Again, since this fan wasn't traditionally wired, I had to come up with another way.So, I bought 18 gauge wire, the same as the fan wiring, and used it to wire the switch. All you have to do is splice on wire to the black wire coming from the fan and then splice another wire to the black wire coming from the extension cord. Those two wires are ran along my ceiling to the back wall where I wired them into the switch. There are two connections labeled A and F that you screw the wires into. F is the wire coming from the fan, A is the wire coming from the power. Once those were connected and the fan plugged into the outlet it worked like a charm!So far I am very pleased with how everything is working. The fan moves a ton of air which was the goal, it doesn't wobble or make noise, was affordable and easy to install. All in all a great product that I would definitely buy again and would highly recommend.

These are really solid fans, you really need to put them in a room with at least 10 to 12 ft high ceilingsI was going to use these in rooms with 8 ft ceilings that's just a little too tight outside of that these are awesome for the price

I bought this fan for my shop. It works well and I did not notice the loudness others have noted. The included switch works well and is fitting in a shop however it would look terrible in side a home. Air movement is great.

I bought four of these for a customer to install in their laundry mat. It had harbor breeze home units that had died. These looked more like something that would be in a commercial setting with metal fan blades.The install was very simple. Not much to assemble other than putting the fan blades on the motor. I departed from the instructions on that step and installed them before hanging the fan on the bracket. Being only three blades gave me plenty of room to get the wiring done. Installing them after it was hung would have been more difficult because you would have to put the screws in from the topside without as much space or visibility.Since they were Westinghouse brand I had hoped they were made in North America. I hoped in vain. Made in China. Other than that they installed easily and worked fine.We will see about longevity

After a month of 24/7 use, I now have some experience. By far the best ceiling fan at any price. At $55, it moves more air and looks more contemporary & sleeker than any $500 designer fan. Same fan as the brushed nickel model so read those reviews as well. Set to the lowest speed, it moves as much air as some residential fans move at their highest speed.I have it mounted above my bed. On the highest speed, it moves so much air it blows the Sunday paper apart & off the bed. Standard installation will lower the fan blades almost 2 ft so if you have 8ft ceilings, it's too dangerous for residential installation. The blades are metal, move at an incredible speed & could probably slice a tomato. You do not want them clipping your hand. BUT ... the down rod can easily be cut in half (with only modification being to drill a new cross mounting hole in the rod, keeping the blades safely above 7ft. Have never had to sleep with the fan set to "high" but the dogs love sleeping under it on hot days and I find that it takes minutes to cool down the room before bed if I turn on the A/C + the fan on high for a few minutes, then back to second lowest speed when I crawl into bed. Saves running the A/C in there all day.To address, other writers' criticisms:- the motor itself is whisper quiet. Quieter than many other brands. But it is impossible to move that much air without hearing the sound of rushing air. Set on "high" there almost a slight "helicopter chop" sound but that's not the motor, that's the metal blades slicing thru the air. But remember, for me, the blades are only 4 feet above the bed. Mounted from a 14 ft ceiling, you might not hear it at all. To me it's "white noise" that drowns out other sounds (but not the TV) but again, I have never had to set it higher than "medium" to stay cool at night. Your choice: strong quiet motor that blows a lot of air that creates some wind noise set on the highest when you really need it, or suffer thru a hot night when you are dying for a breeze.- Lot of criticism of the old fashion looking surface mount box switch. So much so that I ordered a slide dimmer at the same time. But at time of installation, I read NOT to use an electronic dimmer (why, I don't know). And know from other installations, some dimmers can cause the motor to hum. If you have a row of switches, the standard surface box switch could present an installation challenge. In my case, the fan switch is by itself. So rather than risk a potential humming noise, I used the provided switch. After 2 days, I got use to it. It looks like a regular thermostat. Bid deal. Plus I like that the switch "clicks" from one speed to the next, as opposed to sliding. So each position is always the same speed, which matters because since this fan is powerful, it can take a minute or more for the motor to get the blades spinning at the speed you set. There's no second guessing if you set it to the correct speed like there would be with a sliding dimmer switch.- And there is no "reverse switch". Again, big deal. Google the web and you'll find some expert opinions that the "winter" & "summer" settings for ceiling fans is a marketing myth. It doesn't matter if the fan pulls the cold air up or pushes the hot air down, once you've got the air circulating, there are no longer any different temperature zones in the room. The pros just say to use low or medium speeds in winter to avoid a "wind chill" effect.Lastly, easiest fan I've EVER installed. All others have required a second pair of hands to hold it while I connect the wires.Suggestion:- mount the blades PRIOR to lifting the motor onto the socket. When it's fully assembled all you have to do is lift the motor with blades and place the ball into the socket holder. That's it. No more holding a heavy motor. Then do the wire connections. There are only 3 blades, easy to work around them connecting the wires and beats trying to climb even higher later to mount the blades from the top.- Use rubber, even plain old weather stripping between all screw connections, between the holding bracket & the junction box, even between the ball & the socket to dampen any vibration noise. During the first week, I would occasionally hear a rhythmic "clicking noise" if the fan was set too long at the same speed. It had no relation to the speed of the fan (so I knew it wasn't the fan blades hitting anything) and it disappeared if I slightly rocked the based of the fan (carefully) while it was spinning. After trial and error, I discovered it was the electrical wire nut covers tapping against each other inside the junction box. Wrapping them with insulating foam and electrical tape solved the problem.