iSonic P4820-WPB Commercial Ultrasonic Cleaner, 2.6Qt/2.5L, White Color, Plastic Basket, 110V

worked perfect, just like the one I bought 5 years ago.

Following the directions printing on the bottle, after 15 minutes in the ultrasonic cleaner, the 45acp casings looked new - there was no carbon or primer burns either inside the brass or in the primer pockets.Afterwards, the washing with clean water was straightforward without complications.I was so impressed with this product's results I decided to re-clean casings that had been "cleaned" with a different manufacturer's product.The results were startling. Using the recommended 1:40 ratio, the iSonic CSBC001 made the already cleaned brass significantly cleaner-brighter When finished, the solution in the ultrasonic tank went from clear to murky - and this, I repeat, was after cleaning brass casings that had been previously cleaned with a different brass cleaning solution..This product deserves 6 stars and I'm definitely re-ordering iSonic CSBC001.

I like the ease of use. Very simple. Put in water, cleaning solution based on what you are cleaning, turn on timer and heater if desired. I used it to clean hand guns. I field stripped the guns and put the parts in the iSonic. Remember to remove any lasers or anything with batteries. One revolver was too large to fit all the way in, so i had the handle sticking out above the water line. I didn't really need to clean the handle so that was ok. If I did, I would just turn it around and put handle in first and re run the iSonic. I plan to use this maybe every six months to do a thorough cleaning. It is important, vital, to lube and oil all the areas needed as this cleaner removes it all. The handguns need to have oil to protect the moving parts. Check on Youtube if you are unsure what areas need to be oiled. Great iSonic unit.

So, got this to clean titanium silencer baffles. 22LR ~600 rds, filthy as hell (btw, CCI 975CC is sick quiet!). Tried dropping them in the basket with a 50/50 mix of CLR and water, 3x 480 seconds with heat and it kinda sorta worked, but not very well. LOTS of carbon buildup still on the baffles, a bit less so on those right over the transducer. What worked amazingly well was:1) putting the baffles in an old fashioned glass2) add 50/50 mix of CLR and water3) fill the Basin with water only4) set the old fashioned glass directly on the transducer.Ran for 480 seconds, NO heat, and there was 0, ziltch, nada carbon at all on the baffles - like new! The transducer only really gets to those items directly over the transducer. Anything else in the basket really doesn't get touched at all. Now, let's see how long this cleaner really lasts before it craps out...

Funciona muy bien, tiene muy buena calidad

I destroyed the one that came with my HF sonic bath when I attempted to clean a brake part for my motorcycle in brake fluid. Brake fluid and plastic don’t play well. Lesson learned. I bought this basket as a replacement.

Wow for 9mm brass cartridge case cleaning. My 9mm brass looks like new! Clean inside, outside and even the primer pocket is shinny. Used directions on bottle: 40:1 mixture, rinsed cartridge immediately after cleaning in a HF ultrasonic cleaner. I also rinsed the ultrasonic cleaner and wiped dry with a towel. 2 ½ cups of tap water and 1 ½ tablespoons of this CSBC001 solution which just barely went over the minimum mark in my cleaner. 3 - 480 second cycles later I had over 75 perfectly cleaned 9mm brass. I did warm the solution up to around 125-130 degrees in my microwave and then used the heater function on my HF cleaner off and on to keep temperature in that range during the 3 cycles. Used a HF laser temperature measurer to check temperature. Perhaps next time I will poor the solution out after only one cycle and see how they look. Kind of hard to pull the HF short basket out of hot water, so poured the solution out of the cleaner. Very impressed with this solution. I first tried tap water and dawn dish soap and was not happy with the results. Will buy more of this when I run out.

Item as described