Zulkit Junction Box ABS Plastic Dustproof Waterproof IP65 Universal Electrical Boxes Project Enclosure with Fixed Ear Black 3.94 x 2.68 x 1.97 Inch (100 x 68 x 50 mm) (Pack of 1)

Good box well made perfect for my project

It is a good quality box. It only has a few standoffs so most of the space is free for holding components. Solid construction and cover comes off and goes on easily. Bought 2 more today.

I used one of these to create a waterproof switch box for our outdoor cat shelter's heated floor. The ample size gave me plenty of room for what I needed, which was just space for 2 switches and the main power entry point. The included pre-drilled holes/mounting points are a welcome touch as well. There are numerous spots inside for stand-offs or mounting items inside, although I didn't utilize any of them. Being made of ABS, it will obviously be brittle, but working with care, you can easily avoid any accidental cracks/breakage. I used a combination of my drill and dremel to cut out the openings for the 2 power switches and the actual power cable's female port. The seal/gasket material that is included was more than enough, and I've found that as long as you tighten everything down EVENLY, it creates a very good seal.

This project box is exactly as described. Dimensions are accurate, and it feels about as sturdy as one would expect for the price. Inside there are a few molded stand-offs and a pair of brass threaded inserts for mounting things if you need them. A nice touch is that the cover is held in place by machine screws, with threaded inserts pressed into the box - other project boxes use self-tapping screws that thread directly into the plastic. The only thing I didn't like that much is the fact that the waterproof seal was not a gasket or an o-ring style continuous seal. Instead what you get is a "noodle" type that has to be trimmed to fit then glued together (for best results.)

I bought the "Junction Box, Zulkit Project Box Waterproof Dustproof IP65 Universal Electrical Boxes Enclosure with Fixed Ear Black 4.5 x 3.5 x 2.2 inch (115 x 90 x 55 mm)(Pack of 1)"Bought this to house a LED wireless controller attached to my spa. I needed the box to be outside of the spa because of where the low power was installed and length requirements of the low voltage wiring to LEDs. Anyway, this box did the trick.I drilled 2 holes for the wiring on the bottom and used grommets. The generic LED controller (one of these cheap small china made controllers) fit nicely in it. I put the cover on with the supplied rubber spline for the seal. The box has a little channel to insert the spline. You want to make sure you install it correctly and not leave any gaps. The supplied strews were nice as well.As you see from the attached picture, this box sees plenty of water. From rain and the spa itself. I open the box the other day and it was bone dry. Perfect.The box itself feels solid and sturdy. For under $10, it's does the job.We'll see over time if the seal holds and if the box fades at all. Only been a few months.

This year I wanted to line the sidewalk up to my house with a string of RGB smart Christmas lights. I put each light on a stake that pushes into the dirt and aligns level with the sidewalk. However, the length of my sidewalk was such that I had to buy a longer string of lights than I had sidewalk, so I had about 17 extra lights that had nowhere to go. So I purchased caps where I could remove the bulbs and cap off the sockets - mistake. I should have removed the bulbs BEFORE I purchased the caps and would have noticed that the light itself is not part of the bulb. The bulbs are just caps themselves, the light is built into the socket and cannot be removed. So I returned the caps and wondered how I could solve this.I thought that maybe a waterproof box where I could hide the extra 17 lights inside would work so ordered this. This box is plastic, a rectangular shape with no holes on the top or sides except for the screw holes. It comes with a piece of elastic gasket that you can easily insert into a groove on the edges to help keep it waterproof when the top is screwed on. I checked to see that the 17 lights would fit and seeing that they would, I then drilled a 1" hole into the side of the box with a spade bit (very easy) then fed the 17 lights/bulbs into the box. I screwed on the lid and hid the box in the grass next to the last lit bulb on the sidewalk. Because it's black, one can hardly see it. There's still the issue of the hole in the box where I fed the lights being open to the elements or bugs climbing in, but I plan to use a gasket or waterproof tape to block that off. When I remove the lights after the season is over, these 17 will just stay in the box, ready for next year.This box worked great for my Christmas light needs - especially because I was doing a sidewalk, so I could hide the box in the grass. If I were doing a roof line and had extra lights it might be a challenge to hide the box but I guess it's not impossible. Nevertheless, this turned out to be a great solution to having too many lights on the line.

I bought one of these to house an ESP32 development board on an ElectroCookie ESP32 Terminal Block Shield Kit (ASIN: B092H9FM3R, pictured). I was impressed enough by the quality that I bought another to house electronics and connections for my cistern sensors. The second two photographs show how I mounted an ultrasonic sensor and electronics for a pH probe in it. The ABS material is strong and easy to work with. The gasket and screws with metal bolts make me confident that they will work in an exposed location. This would be my choice if I needed another project box.

Pretty standard ABS box. The seal supplied seems to work well and was easy to install. It worked well with my project. I would buy it again.